|
The Box t
|
|
|
07batty
Newbie
|
2. April 2009 @ 16:00 |
Link to this message
|
|
Hi,
Can anybody assist, came home this evening and found all channels gone on the box t I have.based in north cork.
The version have is the Box T API:501e_E Boot Version 7.0 12 december 2007
Reception is through an aerial on the roof and again this is from ***rus
Any ideas???
|
|
Advertisement
|
 |
|
|
Junior Member
|
2. April 2009 @ 16:22 |
Link to this message
|
|
im the same only rte 1,got it sorted last time off this site hang in there
|
|
amigo2007
Newbie
|
2. April 2009 @ 17:54 |
Link to this message
|
|
Hi Lads
Im the same ere, in blesso only gettin rte 1
can anyone help?
|
Newbie
|
3. April 2009 @ 06:25 |
Link to this message
|
i'm the same and have read a load of other threads and this is what i found.
if you upload the latest firmware using the serial to serial cable on your starview box-t and then scan the channels you may get it to work.
otherwise you will have to purchase the kryptview box which works on nagravision 3.
hope this helps
www.youtube.com/watch?v=rF50OkMweWk
|
|
glog
Junior Member
|
3. April 2009 @ 06:37 |
Link to this message
|
|
iraelite,
I think you need to do more research.What you have quoted is incorrect.
gLog
|
Member
|
3. April 2009 @ 07:00 |
Link to this message
|
spot on Glog, to correct him- no box will work on N3.(Yet)
@ 07batty, if updateing your firmware does not work, manually enter the newest 'Kxxx' needed for it to work!
Get out of that garden!
|
|
giggsy07
Junior Member
|
3. April 2009 @ 07:41 |
Link to this message
|
|
Well guys i entered the new Kxxx manually and still no joy.Box-T by the way..tried flashing the lot...
|
|
darst
Member
|
3. April 2009 @ 08:20 |
Link to this message
|
|
make sure key emu is on after you have entered and SAVED the k. also when the cas menu is accessed the provider id that you will see is 5401 for n**, scroll right till you get 5E01 for c****s then enter k and save
This message has been edited since posting. Last time this message was edited on 3. April 2009 @ 08:21
|
Member
|
3. April 2009 @ 08:29 |
Link to this message
|
Originally posted by darst:
make sure key emu is on after you have entered and SAVED the k. also when the cas menu is accessed the provider id that you will see is 5401 for n**, scroll right till you get 5E01 for c****s then enter k and save
hi darst.i tried manual entering k-ys for my neighbour,doesnt work.tried everything.i think they did a little more than roll k-ys ?.
jvob
|
|
darst
Member
|
3. April 2009 @ 08:42 |
Link to this message
|
well all i can tell you is mine autorolled and is working fine. are you sure you entered them in proper provider id and saved them after entering, then check key emu is on.when you exit back to tv if data updating stays at 0% try turning box off atthr back for a minute then back on. it should work and worth a try
|
|
mickymac
Junior Member
|
3. April 2009 @ 14:14 |
Link to this message
|
Originally posted by 07batty:
Hi,
Can anybody assist, came home this evening and found all channels gone on the box t I have.based in north cork.
The version have is the Box T API:501e_E Boot Version 7.0 12 december 2007
Reception is through an aerial on the roof and again this is from ***rus
Any ideas???
|
|
mickymac
Junior Member
|
3. April 2009 @ 14:19 |
Link to this message
|
Hi go to fixya .com for codes for boxt cant post codes here.type in what your looking for.when you get codes go to menu type in 1570 go to nagravision make sure provider is chorus and the emu is switched on then type in codes this worked for me in the last hour good luck
|
AfterDawn Addict
|
3. April 2009 @ 14:29 |
Link to this message
|
if u dont have the latest firmware on ur box,why do u expect it to work,everybody was told to update their box and now everybody in a panic,all tuts and firmwares in eamos library
|
Member
|
3. April 2009 @ 16:12 |
Link to this message
|
Originally posted by darst:
well all i can tell you is mine autorolled and is working fine. are you sure you entered them in proper provider id and saved them after entering, then check key emu is on.when you exit back to tv if data updating stays at 0% try turning box off atthr back for a minute then back on. it should work and worth a try
thanks,got it sorted.
jvob
|
|
Advertisement
|
|
|
Senior Member
|
3. April 2009 @ 16:33 |
Link to this message
|
Originally posted by iraelite:
i'm the same and have read a load of other threads and this is what i found.
if you upload the latest firmware using the serial to serial cable on your starview box-t and then scan the channels you may get it to work.
otherwise you will have to purchase the kryptview box which works on nagravision 3.
hope this helps
Just to clarify something, the Kryptview does not work on Nagra3, but it works on Nagra2 which is what is being used at the moment before a full migration to Nagra3.
Whatever you say, say nothing when you talk about you know what for if you know who might hear you, you know what youll get. Youll be sent off to you know where for you would not know how long. Maybe I could search through the threads so you dont have to ??
|
