|
BenQ Installation trouble (Theres more)
|
|
Newbie
|
22. September 2009 @ 07:45 |
Link to this message
|
Hi basically when I open jungleflasher it says no comports were found, ive been told to ignore this as its for Lite Ons but when I look for my drive in the ports list its not there, anyone know how to get it to appear? Im using Windows Vista 32-bit and heres everything ive done so far:
bought a VIA VT6421 and installed it to my PC, then I went and followed a guide to remove the drivers to stop an error occuring so when I look at it in my hardware section its there but its got an explaination mark beside it.
Connected the Sata cables from my PC to the xbox 360
Installed PortI/O and the frameworks required
Got jungleflasher and the firmware in the firmware folder.
Turned on xbox 360
Opened jungleflasher to see the error
When I look on the port like the 4 VIA VT6421 ports are there but they all say no drives found
Anyone see something im doing wrong?
|
|
Advertisement
|
 |
|
|
Newbie
|
22. September 2009 @ 08:16 |
Link to this message
|
Sorry couldnt find an edit button, I just tried doing it with the drive half open and it still didnt find the drive.
Also when installing the VIA card I plug it into a PCI port then plug the sata cable that came with it into the card and then into the motherboard right?
Then I connect a 2nd sata cable into the free port on the back of the VIA and connect that to my 360? (thats what I did, is that correct?)
|
Member
|
22. September 2009 @ 08:24 |
Link to this message
|
|
ok i take it you've read the tut either from the JF site or Leerage's? both are really well written but my fave is Leerage as he explains it in laymans terms. if you need it then leerages tut is in his sig.
have you got it in vendor mode yet? a couple of my drives needed me to reboot the pc before the drive would register. now i got myself a CK3 pro things couldn't be simpler.
|
Member
|
22. September 2009 @ 08:27 |
Link to this message
|
Originally posted by Magatame:
Sorry couldnt find an edit button, I just tried doing it with the drive half open and it still didnt find the drive.
Also when installing the VIA card I plug it into a PCI port then plug the sata cable that came with it into the card and then into the motherboard right?
Then I connect a 2nd sata cable into the free port on the back of the VIA and connect that to my 360? (thats what I did, is that correct?)
no you only need 1 sata cable from the pci card to the DVD drive.... wow your set up must look like the spaghetti junction :)
|
Newbie
|
22. September 2009 @ 09:07 |
Link to this message
|
Okay having a new issue now, got it to find the BenQ drive and clicked to unlock BenQ, then as far as I could see it was successful, after that was done I clicked "Read" but that failed and now it cant find the drive again :S
|
AfterDawn Addict
2 product reviews
|
22. September 2009 @ 09:09 |
Link to this message
|
|
Can you please post the log? Thanks.
|
Newbie
|
22. September 2009 @ 09:15 |
Link to this message
|
|
Uh I just restarted my computer if I put it on and save the log again can you look at that? :\
|
AfterDawn Addict
|
22. September 2009 @ 09:16 |
Link to this message
|
make sure you plug the drive into sata port 1. it should be the one closest to the front of your PC.
Come talk with us on efnet at #elitemods !!! or just click ME
ALSO, DO NOT SEND ME MESSAGES ON LIVE REGARDING MODDING CONSOLES, OR HOW I PLAYED A CERTAIN GAME EARLY. I WILL NOT RESPOND. I WILL INSTEAD DELETE YOUR MESSAGE, AND BLOCK ALL COMMUNICATION FROM YOU. JUST SEND ME A PM ON HERE. |
Newbie
|
22. September 2009 @ 09:25 |
Link to this message
|
|
Okay got it going now, Just clicked "Write" and its frooze on "Writing Bank 0" how long should this part take?
|
AfterDawn Addict
|
22. September 2009 @ 09:27 |
Link to this message
|
|
should only take around 5 seconds or so. i hope you saved your FW when you dumped it, other wise you are screwed. you can try sending the outro, putting it back in vendor mode and attempting the write again. if that doesnt work, then you're going to have to use dosflash.
Come talk with us on efnet at #elitemods !!! or just click ME
ALSO, DO NOT SEND ME MESSAGES ON LIVE REGARDING MODDING CONSOLES, OR HOW I PLAYED A CERTAIN GAME EARLY. I WILL NOT RESPOND. I WILL INSTEAD DELETE YOUR MESSAGE, AND BLOCK ALL COMMUNICATION FROM YOU. JUST SEND ME A PM ON HERE. |
Newbie
|
22. September 2009 @ 09:29 |
Link to this message
|
I saved some sort of firmware would the filename be: BENQ-OFW ?
|
AfterDawn Addict
|
22. September 2009 @ 09:31 |
Link to this message
|
|
that would be what you need. good thing you saved it.
Come talk with us on efnet at #elitemods !!! or just click ME
ALSO, DO NOT SEND ME MESSAGES ON LIVE REGARDING MODDING CONSOLES, OR HOW I PLAYED A CERTAIN GAME EARLY. I WILL NOT RESPOND. I WILL INSTEAD DELETE YOUR MESSAGE, AND BLOCK ALL COMMUNICATION FROM YOU. JUST SEND ME A PM ON HERE. |
Newbie
|
22. September 2009 @ 09:33 |
Link to this message
|
Okay I tried the outro thing and it said this:
Sending Vendor Outro to port 0xC800
So I assumed it was done and click and unlocked it to BenQ again.
I then clicked Read and now its sitting at
Reading Bank 0: ................
Reading Bank 1: ................
Reading Bank 2: ................
Reading Bank 3: ................
and nothing is happening, what should I do?
|
AfterDawn Addict
|
22. September 2009 @ 09:38 |
Link to this message
|
|
if you already have dumped the FW theres no need to read it again. just make sure you have your source and your destination FW correct (the page that JF takes you to when you click yes on autoload). then just proceed on writing the FW again.
Come talk with us on efnet at #elitemods !!! or just click ME
ALSO, DO NOT SEND ME MESSAGES ON LIVE REGARDING MODDING CONSOLES, OR HOW I PLAYED A CERTAIN GAME EARLY. I WILL NOT RESPOND. I WILL INSTEAD DELETE YOUR MESSAGE, AND BLOCK ALL COMMUNICATION FROM YOU. JUST SEND ME A PM ON HERE. |
Newbie
|
22. September 2009 @ 09:39 |
Link to this message
|
It worked! Heres the log if your interested:
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
JungleFlasher 0.1.66 Beta
Session Started Tue Sep 22 14:37:04 2009
This is a 32 bit process running on 2 x 32 bit CPUs
PortIO is installed and running.
Found 4 I/O Ports.
Found 0 Com Ports.
Found 8 windows drives C: F: G: H: I: J: K: L:
Found 2 CD/DVD drives J: L:
Sending Vendor Outro to port 0xC800
Sending Magic Keys to Drive on port 0x0xC800
..........................................
Done!
Sending Vendor Intro
Requesting Device ID
Manufacturer ID: 0xC2
Device ID: 0x11
Flash Name: MXIC(MX25L2005)
Flash Size: 262144 bytes
Loading Source File C:\Users\John\Desktop\BENQ-OFW.bin
Inquiry string found
Identify string found
DVD key found @ 0xC040 key is 2DCC0132262C58A422D9E412283E7EF8
Firmware is Benq OSIG: PBDS VAD6038-64930C
Firmware type is: Stock
Auto-Loading target file C:\Users\John\Desktop\JungleFlasher v0.1.66 Beta (49)\firmware\ix16-benq.bin
Target File MD5 hash is: f36c85c5bfba325b283417f8643d7c27
Genuine Benq iXtreme 1.6
Inquiry string found
Identify string found
DVD key found @ 0xE030 key is 77777777777777777777777777777777
Firmware is Benq OSIG: PBDS VAD6038-64930C
Firmware type is: iXtreme v1.60-12x-FINAL-VAD6038
Spoofing Target
DVD Key copied to target
Inquiry strings identical
Identify strings identical
0xFF00 area copied for Benq to Benq
Target f/w saved as: C:\Users\John\Desktop\Benq_CFW3.bin
Getting Status from port 0xC800
SPi flash found with Status 0x73
Sending Chip Erase to Port 0xC800
Writing target buffer to flash
Writing Bank 0: ................
Writing Bank 1: ................
Writing Bank 2: ................
Writing Bank 3: ................
Flash Verification Test !
Reading Bank 0: ................
Reading Bank 1: ................
Reading Bank 2: ................
Reading Bank 3: ................
Write verified OK !
Sending Vendor Outro to port 0xC800
Now gotta put the 360 back together again XD
|
AfterDawn Addict
2 product reviews
|
22. September 2009 @ 09:40 |
Link to this message
|
|
Looks good.
|
Newbie
|
22. September 2009 @ 09:43 |
Link to this message
|
|
BTW thanks for the help I prob would have bricked my 360 if it wasnt for your help! <3
|
Newbie
|
22. September 2009 @ 10:13 |
Link to this message
|
|
:'( I put everything back together and tried a game and it didnt work.. I just realised that I left the disk drive unplugged.. It takes me forever to open this thing up lol .. Damn
|
Newbie
|
22. September 2009 @ 10:38 |
Link to this message
|
|
Okay so I put everything back together again and put in an old game I had, it reads it for a few seconds then gives me the open tray message again, like theres no game in the drive? Any ideas?
|
Newbie
|
22. September 2009 @ 10:42 |
Link to this message
|
|
False alarm, the disc must of got damaged at one point or another in the past week. :(
|
|
Advertisement
|
|
|
Member
|
22. September 2009 @ 10:44 |
Link to this message
|
Originally posted by Magatame:
False alarm, the disc must of got damaged at one point or another in the past week. :(
ok :) glad you got it all sorted in the end
|
