|
Help...flashing a lite-on 74850C
|
|
|
eazyrider
Junior Member
|
26. November 2009 @ 01:45 |
Link to this message
|
can someone please help me.. i've followed all the tutorials but still having problems..
-i have a sata raid 6421 controller
-xtractor pro w/ probe
-newest version of jungle flasher
so i do what everyone one says, desable the sata board, erase the driver, enable sata board, reboot..
go into jungleflasher, and find the port.
only problem is; my sata board comes up, but not my drive..DRIVE IS undetected..tried in the xtractor reader as well,,
i'm plugging my xtrator in with the USB, instead on a serial..and there was a time it would go to in jungleflasher COM 3, usb!!
but i can't figure out whats happening, or maybe i just need to try with a serial cabler..
any suggestions????
|
|
Advertisement
|
 |
|
|
AfterDawn Addict
2 product reviews
|
26. November 2009 @ 02:04 |
Link to this message
|
Have you tried a different SATA port on the card?
|
|
eazyrider
Junior Member
|
26. November 2009 @ 02:20 |
Link to this message
|
|
yes..i have one on the inside, and one on the top of the card..
tried both of them
|
|
asjb69
Newbie
|
26. November 2009 @ 02:38 |
Link to this message
|
go into your bios setup try using legacy instead of native on the sata chip
This message has been edited since posting. Last time this message was edited on 26. November 2009 @ 02:39
|
|
eazyrider
Junior Member
|
26. November 2009 @ 02:50 |
Link to this message
|
how do i do that??
Quote:
go into your bios setup try using legacy instead of native on the sata chip
|
|
eazyrider
Junior Member
|
26. November 2009 @ 02:52 |
Link to this message
|
you don't think if i tried a serial cable it would make a difference?
i heard the xtractor pro is made more for a serial than a usb..
i just wonder why i can't get jungleflasher into Com 3, so it recognizes my USB..
its like its not recognizing my usb connection. and i've installed usb drivers, unless, i installed the wrong ones?
|
|
eazyrider
Junior Member
|
27. November 2009 @ 03:12 |
Link to this message
|
i'm using a maximus xtractor..and my guess is my comp is recognizing it, hence not recognizing my drive...
any suggestions???
|
|
big_green
Junior Member
|
27. November 2009 @ 14:40 |
Link to this message
|
Have you tried installing the correct portIO drivers?
|
|
jf1981
Suspended due to non-functional email address
|
28. November 2009 @ 03:00 |
Link to this message
|
hi, (sorry didn't want to make new thread) is it possible to flash a benq drive with SIL3112 chipset?
|
|
hanna21
Suspended permanently
|
28. November 2009 @ 15:48 |
Link to this message
|
|
This message has been edited since posting. Last time this message was edited on 28. November 2009 @ 17:27
|
AfterDawn Addict
|
28. November 2009 @ 16:27 |
Link to this message
|
Originally posted by hanna21:
all tutorials and videos in this forum www.yahooomood.com injoy
How many times you gonna post this BS.
PRIVATE MESSAGES ASKING FOR HELP WILL BE IGNORED, USE THE FORUMS TO ASK YOUR QUESTIONS!!! |
|
big_green
Junior Member
|
28. November 2009 @ 16:37 |
Link to this message
|
Originally posted by sicdude:
Originally posted by hanna21:
all tutorials and videos in this forum http://i'manmidiot.com edited by ddp injoy
How many times you gonna post this BS.
Seriously, it's spam at this point. If you have the tuts available on your forum that could help the OP, then post the info here.
- OP, I had some troubles with JungleFlasher recognizing my connection, what I did was I used my ck3 with a serial connection and installed the PortIO drivers without restarting my comp. When I restarted the original drivers kept getting restored automatically.
This message has been edited since posting. Last time this message was edited on 28. November 2009 @ 17:28
|
|
Advertisement
|
|
|
|
ddp
Moderator
|
28. November 2009 @ 17:30 |
Link to this message
|
|
sicdud, can you edit your post to reflect what i've done about hanna21?
|
