jungle flasher wont open when i conect my xbox 360

Advertise at AfterDawn.com

Link to us!

Private messages

Compose a private message

List of all updated threads

Threads without replies

Search messages

Friday 19.9.2025 / 01:30

Search AfterDawn Forums:

afterdawn.com > forums > consoles > xbox 360 - modding & hacking > jungle flasher wont open when i conect my xbox 360

Browse by topic

Forums

Start a new thread

jungle flasher wont open when i conect my xbox 360

Jump to:

Posted

Message

yucafien2

Junior Member

31. December 2009 @ 18:12

Link to this message

when i connect my xbox 360 and put it into b mode i try to open jungle flasher or iprep and it doesnt apear.the same when i try to install port1o32. can any one help me i need to mod this xbox.
thxs
yucafien2

ps. i have a compatable sata chip set and i am running on xp

[ + quote]

yucafien2

Junior Member

31. December 2009 @ 20:46

Link to this message

anyone please? i need help

[ + quote]

metalguy

Junior Member

1. January 2010 @ 02:51

Link to this message

Originally posted by yucafien2:
when i connect my xbox 360 and put it into b mode i try to open jungle flasher or iprep and it doesnt apear.the same when i try to install port1o32. can any one help me i need to mod this xbox.
thxs
yucafien2

ps. i have a compatable sata chip set and i am running on xp

did you install the drivers for your sata card? Because you're not supposed to.

also if you can't even open iprep make the bootable drive then you might be missing .framework 2.0 or an update for it. Check to see if you have all the updates for it.

Since you talked about mode b i'm guessing you have a hitachi drive? if so i don't know if you need to power cycle it but you could try that.

[ + quote]

This message has been edited since posting. Last time this message was edited on 1. January 2010 @ 08:28

yucafien2

Junior Member

1. January 2010 @ 15:06

Link to this message

no the computer came with the driver already installed.and i have made the bootable drive i jus need to make the firmware for my benq

[ + quote]

metalguy

Junior Member

2. January 2010 @ 00:47

Link to this message

Originally posted by yucafien2:
did you install the drivers for your sata card? Because you're not supposed to.

also if you can't even open iprep make the bootable drive then you might be missing .framework 2.0 or an update for it. Check to see if you have all the updates for it.

Since you talked about mode b i'm guessing you have a hitachi drive? if so i don't know if you need to power cycle it but you could try
that.

no the computer came with the driver already installed.and i have made the bootable drive i jus need to make the firmware for my benq

Maybe you should tell me the steps you have taken so i can get a picture of what you're doing.

Here's how it should be done for iprep

download benq ixtreme firmware
install portio drivers
open iprep
select your compatible sata controller (if your using onboard its probably nvidia if not then via 6421)
write down primary port number(this is the port you will plug your benq into)
select a com port(if you have portio installed your usb should be in the list)
pick a target device (usb drive?)
Load the ixtreme firmware in the benq tab
check the box "format and make bootable"
after that hit start

if you did all of the steps i mentioned then you should be ready to flash your drive. let me know if you've gotten that far.

Also, are you sure your sata controller is compatible? if its onboard then you should not need to uninstall the drivers and your benq should show up in device manager. try plugging it in and going to device manager then hit refresh and see if your drive pops up. If not then your on-board controller may not be compatible.

[ + quote]

Start a new thread

Related forum topics	Posts	Last post	Forum room
Microsoft finally discontinues Xbox 360	1	22. April 2016	News comments
Motorola unveils new series of Moto 360 smartwatches	2	5. September 2015	News comments
Microsoft makes 'Forza Horizon 2: Presents Fast & Furious' free for Xbox One, Xbox 360	7	31. March 2015	News comments
Moto 360 coming soon in gold and with a new leather band?	1	1. November 2014	News comments
Buying 'Destiny' for PS3, Xbox 360? Bungie giving vouchers to upgrade to current gen for free	1	8. September 2014	News comments
Best Buy leaks Motorola Moto 360 price, specs, features	1	18. August 2014	News comments
Google shows off prototypes of Moto 360 and LG G Watch	4	4. June 2014	News comments
Xbox 360 FLASH MOD HELP	6	2. June 2014	Xbox 360 - Modding & Hacking
Dismantled my 360 to repair Disk Drive - Now Controllers won't sync (wired & wireless)	3	1. June 2014	Xbox 360 - Modding & Hacking
Have 60GB hard drive on original 360, can put bigger hard drive in 60GB casing?	8	10. May 2014	Xbox 360 - Modding & Hacking

afterdawn.com > forums > consoles > xbox 360 - modding & hacking > jungle flasher wont open when i conect my xbox 360


		User name	Password

		Not registered yet? Register here. Lost your password? Click here.