|
having trouble with jungle flasher 1.70
|
|
|
N0_0ne
Member
|
25. January 2010 @ 19:02 |
Link to this message
|
Ok, so I put original fw back on my lite on, updated on live. Now Im trying to put liteon lt firware on my drive and I get failed verification at the end. Do I use the auto feature on jungle flasher? Im going by this tutorial because I cant find a 1.70 tut.
http://forums.afterdawn.com/t.cfm/f-152/...ncluded-781857/
|
|
Advertisement
|
 |
|
|
|
N0_0ne
Member
|
25. January 2010 @ 19:13 |
Link to this message
|
|
no I get "no drive detected" no matter which i/o port I choose. Did I ruin my drive?
|
AfterDawn Addict
2 product reviews
|
25. January 2010 @ 20:33 |
Link to this message
|
Does the drive still eject?
Make sure you have your DVDkey etc before continuing.
Connect it back up to the same SATA port you were using and make sure the same I/O Port is selected in JF. Click LiteOn erase and click OK to the next 2 prompts. Once you see the dots go across the bottom, disconnect the power cable from the back of the drive for 1 second and then plug it back in. If you are using a connectivity kit, you can shut it off and then turn it back on. You should get 0x72 status and you can write the firmware now.
|
|
N0_0ne
Member
|
25. January 2010 @ 22:39 |
Link to this message
|
|
ok now for some reason as soon as I click my drive on with my ck3 my cursor freezes so I cant open jf, have you ever heard of that?
|
|
N0_0ne
Member
|
25. January 2010 @ 22:43 |
Link to this message
|
|
it wont eject with the ck3 and wont eject when put back in the 360
|
|
N0_0ne
Member
|
25. January 2010 @ 23:22 |
Link to this message
|
so if my drive is infact bricked, I have a samsung and I have all my info from my liteon, is there a tutorial for swapping the two? Or better yet can I buy a brand new liteon and put my old liteon info on it, I checked ebay and couldnt find anything, any suggestions, thanks
|
Senior Member
|
26. January 2010 @ 00:49 |
Link to this message
|
I doubt your drive is bricked, it's probably stuck in vendor mode but jungleflasher is crashing on you. I would disconnect all your other non-essential devices, swap sata ports and try from the top all over again. If you can get into jungleflasher again and can't get the drive to detect send the intro manually.
"All drives should be updated to Lite Touch + (LT+) firmware if playing on XBOX live. Samsung drives and pre-78/79 Hitachi drives do not utilize AP 2.5. All other drives are considered to be detectable by Microsoft (YMMV). Make sure all rips are ABGX verified, contain SSv2, and patched AP2.5 (where needed). XGD3 must currently be burned on new drive with PC Burner Max firmware for 100% rip. All modded consoles can be potentially unsafe for use on XBOX live."
|
|
N0_0ne
Member
|
26. January 2010 @ 06:23 |
Link to this message
|
|
well I hope you're right man, but Im not sure how to send the intro manually, Im a bit of a noob with jungle flasher. Been using that mod disc since 1.5. Is there a tut for that?
|
|
N0_0ne
Member
|
26. January 2010 @ 06:28 |
Link to this message
|
and as for swapping sata ports Im using one on a via card I bought a while back. Although my mb has via chipset. So are you saying I should even disconnect the ide devices?
|
|
Kelewan
Member
|
26. January 2010 @ 08:00 |
Link to this message
|
Dude, use the edit button instead on double/triple posting. Have you uninstalled the via drivers for your MB. I read that this can cause issues.
|
|
N0_0ne
Member
|
26. January 2010 @ 08:27 |
Link to this message
|
if you mean removing these "viamraid.sys" or "vsmraid.sys" then yes, but I will double check as I did this a while ago
sorry about the multiple posts
ok turns out the via.sys was still in the drivers folder, I got rid of that and put portio32.sys in the folder. rebooted. I tried erasing the drive again but it said returned to 0x7F device intro failed. the good news is jf isnt crashing anymore. So since then I clicked intro/deviceID in the flashing tasks and device still failed. Drive is still not being detected.
I noticed theres a FTD2XX.dll file in the jungleflasher folder, should I be copy pasting that somewhere?
This message has been edited since posting. Last time this message was edited on 26. January 2010 @ 09:55
|
|
360lifer
Member
|
26. January 2010 @ 11:41 |
Link to this message
|
You can't brick a liteon. If JF can't fix the issue than you can always just use the dos method to write the firmware.
|
|
Advertisement
|
|
|
|
N0_0ne
Member
|
26. January 2010 @ 13:52 |
Link to this message
|
|
Good to know, well I have found a tutorial for dos32 I cant seem to find a download for it, having trouble connecting to xbins, is there another alternative you know of?
|
