|
burning 360 games and veryfiying layer??
|
|
|
broughsta
Suspended permanently
|
3. March 2010 @ 09:20 |
Link to this message
|
hi all
i have a quick question. when ever i burn a 360 game imbgburn always crashes when verifying the disk.
looks somthing like this
I 13:30:13 Verifying Session 1 of 1... (1 Track, LBA: 0 - 3697695)
I 13:30:13 Verifying Track 1 of 1... (MODE1/2048, LBA: 0 - 3697695)
I 13:30:13 Verifying Layer 0... (LBA: 0 - 1913759)
and stops. the games seem to work fine in the xbox, sometimes i have issues with it saying the disk is dirty when its not and i have to reset which is annoying.
thus i tend to install the game on the ardrive to prevent this, other then that i dont have any problems. so im wondering why im getting this error when burning games.
|
|
Advertisement
|
|
|
|
Senior Member
|
3. March 2010 @ 09:23 |
Link to this message
|
Right, What firmware do you have? LT? also do you use the Wave patcher?...Games that are copied need to be wave patcher or use the activate.iso to boot if you dont have LT.
Also it could be a problem with your burner.. Check around this forum to see if its a suitable drive.
Hope this helps
Ayame, i live for you xxx even though the sight may fade the feelings shall always remain
Ayame, i owe you my life but thats all i have to give to you as you already have my love and my heart
forever yours Joe xxxxx
|
|
broughsta
Suspended permanently
|
3. March 2010 @ 09:23 |
Link to this message
|
i burn at 4 speed, and use these disks.
I 13:30:13 Source Media Type: DVD+R DL (Book Type: DVD-ROM) (Disc ID: RICOHJPN-D01-67) (Speeds: 4x, 6x, 8x)
|
|
broughsta
Suspended permanently
|
3. March 2010 @ 09:29 |
Link to this message
|
my moded xbox is only 6 months old, i was given an active iso disk with the console but becuase all my games are before wav4 i havent needed it of as yet. all i got is halo 3 and resident evil so far.
i have PIONEER DVD-RW DVR-218L with the latest 1.02 firmware.
|
|
broughsta
Suspended permanently
|
3. March 2010 @ 09:33 |
Link to this message
|
|
i havent needed to patch any games of yet, so im wondering why my burns are hanging when being verfied ?
|
|
tigerland
Newbie
|
3. March 2010 @ 09:41 |
Link to this message
|
|
burning at 4 speed, could be causing these errors read the idiots guides to burning that should help you out
HULL CITY fan and proud
|
|
broughsta
Suspended permanently
|
3. March 2010 @ 09:46 |
Link to this message
|
|
ok, but my media wont let me burn at 2.4 i get a message saying tried to get 2.4 maanged 4.
|
|
kgscnc
Suspended due to non-functional email address
|
3. March 2010 @ 09:50 |
Link to this message
|
I just burned a xbox 360 game on imgburn. When I put it in the game system it read the disc then said, "this disc must be played in a xbox 360 console". What am I doing wrong?
|
Senior Member
|
3. March 2010 @ 10:25 |
Link to this message
|
Did you manually set the layer break in the catalogue?
i dont know the number but its something like 191736 etc but yeah you need that..absolutley vital...ill see if i can find the number
Ayame, i live for you xxx even though the sight may fade the feelings shall always remain
Ayame, i owe you my life but thats all i have to give to you as you already have my love and my heart
forever yours Joe xxxxx
|
Senior Member
|
3. March 2010 @ 10:26 |
Link to this message
|
|
L0 = 1913760
Where it says "LBA: 0 -" change the number to 1913760
and make sure its the first layer only!
:) hope this helps
Ayame, i live for you xxx even though the sight may fade the feelings shall always remain
Ayame, i owe you my life but thats all i have to give to you as you already have my love and my heart
forever yours Joe xxxxx
|
|
kgscnc
Suspended due to non-functional email address
|
3. March 2010 @ 10:36 |
Link to this message
|
|
Thanks i see where you put the number in but how do make sure it is the first layer only. thanks so much for you help.
|
Senior Member
|
3. March 2010 @ 10:52 |
Link to this message
|
Layer break should set it to burn in first layer only... IMGburn will tell you that your burning on the first layer only... Make sure you read the error..
it'll say "Hey, I've noticed your only burning to the first layer and its a dual layer DVD, because of how good i am do you want me to set this to burn on two layers?"
or something like that..Just make sure you read it...Even when you set it correctly... ti still writes 0's to the 2nd layer so when you see that been burnt dont panic :P
Ayame, i live for you xxx even though the sight may fade the feelings shall always remain
Ayame, i owe you my life but thats all i have to give to you as you already have my love and my heart
forever yours Joe xxxxx
|
Senior Member
|
3. March 2010 @ 11:12 |
Link to this message
|
MUNKYEARS - What you said in that last post only applies to burning the activate.iso disc, not Xbox 360 games.
Also, this is correct: -
Quote:
LBA: 0 - 1913759
Because 1913760 is the next number following on from that, which denotes the start of the second layer.
There's no issue with your settings broughsta. It could just be that your burner can't read that particular media too well. Try using Verbatims.
|
Senior Member
|
3. March 2010 @ 11:40 |
Link to this message
|
|
Sorry yeah, Im thinking of a different post at the same time :) but thanks for the correction
Ayame, i live for you xxx even though the sight may fade the feelings shall always remain
Ayame, i owe you my life but thats all i have to give to you as you already have my love and my heart
forever yours Joe xxxxx
|
|
kgscnc
Suspended due to non-functional email address
|
3. March 2010 @ 11:45 |
Link to this message
|
i did everything you said but still saying the samething . does it matter that this is a brandnew xbox
|
Senior Member
|
3. March 2010 @ 11:49 |
Link to this message
|
|
Just to clear things up...
Has it been flashed?
i know it sounds like im thinking your a fool, but its a common mistake for people who just think they can burn discs and expect it to work.
Sorry but had to be asked
Ayame, i live for you xxx even though the sight may fade the feelings shall always remain
Ayame, i owe you my life but thats all i have to give to you as you already have my love and my heart
forever yours Joe xxxxx
|
|
kgscnc
Suspended due to non-functional email address
|
3. March 2010 @ 11:53 |
Link to this message
|
|
ask anything you want. lol.I'm a single parent trying to get this to work for my 12 year old son. it came straight out the box from Walmart. how do i flash it.
|
Senior Member
|
3. March 2010 @ 12:01 |
Link to this message
|
Good job i asked :P...
Right, I'm sure someone has wrote a guide on this forum, its around here somewhere...
Flashing it, means to replace the software on the DVD drive in the xbox to allow it to read copied games... Keep the copies of your games safe, they will keep till later after the flashing process.
For a start your gonna need to do two things. I dont know how technical minded you are at this but ill do my best to make it easier for you.
heres an outline of how this will need to be done:
1: break open the xbox.
2: Pull the xbox dvd drive out
3: Buy a ki called the CK3 Pro/lite either will do.
4 connect it to a computer, Download a program and retrieve the DVD password from the drive.
etc...
Sorry its a brief outline...
Ill see if i can dig up the drive
Hope this helps a little
Ayame, i live for you xxx even though the sight may fade the feelings shall always remain
Ayame, i owe you my life but thats all i have to give to you as you already have my love and my heart
forever yours Joe xxxxx
|
|
kgscnc
Suspended due to non-functional email address
|
3. March 2010 @ 12:13 |
Link to this message
|
|
how much does the kit cost and where can you get it from.
|
|
kgscnc
Suspended due to non-functional email address
|
3. March 2010 @ 12:25 |
Link to this message
|
ok. here's my last question if i have the xbox flashed can my son still go online with his xbox live.
|
|
Advertisement
|
|
|
Senior Member
|
4. March 2010 @ 04:15 |
Link to this message
|
|
Anywhere online. Just google it. :)
Yes and No. You need to burn a game in a certain way so he wont get detected. Something called stealh patching. We can help with that when we get you flashed up.
It may be easier and cheaper to let someone do it for you.
Ayame, i live for you xxx even though the sight may fade the feelings shall always remain
Ayame, i owe you my life but thats all i have to give to you as you already have my love and my heart
forever yours Joe xxxxx
|
