|
|
|
Bricked Xbox after flash Liteon 83850C
|
|
|
daoliveri
Newbie
|
16. August 2010 @ 13:40 |
Link to this message
|
After 3 months of buying an Xbox Arcade and a nice size hdd off amazon (did the xbox live update) I decided it was time to flash. I read up and used jungleflasher OLD WAY without the probe. Using the onboard sata and the console to power the Liteon drive. I successfully flashed the drive but now it won't eject and there is a steady green blinking light on the console. Every once in a while i'll cycle the dvd drive power and it will open or close and then i get nothing. I thought it was a firmware issue but now i'm thinking that it is a console issue also. Jungleflasher still reads the drive but LO83info fails every time. Dosflash won't read the drive (never did). I do still have all of the files saved.
Although i have a modded xbox 1, i'm pretty new at the whole flashing scene. Do I now have an expensive paperweight?
|
|
Advertisement
|
 |
|
|
|
coorva
Suspended due to non-functional email address
|
16. August 2010 @ 15:49 |
Link to this message
|
no,,you cant brick liteons,,try and reflash the drive again,,but this time dont read the firmware,,since you allready have the orig firmware,,just go ahead and flash it using the hacked firmware,,are you using lite touch,,its the newest out there,,maybe the first flash didnt take right,,follow the tut to flash not to read the firmware,,see if that works,,cheers
microsoft after a ban wave |
Senior Member
|
16. August 2010 @ 17:15 |
Link to this message
|
|
You can always buy a spare drive and flash that one with the original key...then try with the spare...you'll have your answer on whether you dumped it correctly. Here's to hoping you did.
"All drives should be updated to Lite Touch + (LT+) firmware if playing on XBOX live. Samsung drives and pre-78/79 Hitachi drives do not utilize AP 2.5. All other drives are considered to be detectable by Microsoft (YMMV). Make sure all rips are ABGX verified, contain SSv2, and patched AP2.5 (where needed). XGD3 must currently be burned on new drive with PC Burner Max firmware for 100% rip. All modded consoles can be potentially unsafe for use on XBOX live."
|
|
daoliveri
Newbie
|
16. August 2010 @ 21:34 |
Link to this message
|
JungleFlasher 0.1.75 Beta (152)
Session Started Mon Aug 16 21:18:59 2010
This is a 32 bit process running on 2 x 32 bit CPUs
portio32.sys Driver Installed
portio32.sys Driver Started, thanks Schtrom !
Found 6 I/O Ports.
Found 1 Com Ports.
Found 3 windows drives C: D: H:
Found 0 CD/DVD drives
Loading firmware file D:\JungleFlasher v0.1.75 Beta (152)\Dummy.bin
MD5 hash: dffca742d79dc79dd7eb08e0e13f607b
Inquiry string found
Identify string found
Drive key @ 0xA030 49E2260580FA30F4C5272B25860FE129
Firmware Osig: [PLDS DG-16D2S 8385]
Firmware is: LO83info Extract
Loading firmware file D:\JungleFlasher v0.1.75 Beta (152)\firmware\ix-lt-838v2.bin
MD5 hash: 7381f964ffef44da7bf94aa1dc067fb2
Genuine iXtreme Lite-Touch
Drive key @ n/a 77777777777777777777777777777777
Firmware Osig: [PLDS DG-16D2S 8385]
Firmware is: iXtreme LT
Spoofing Target
DVD Key copied to target
Target is LT - ID strings not copied to Target
Serial data copied from Source to Target
No Calibration data in source
Lite-On-Erase NOT sent
Sending Lite-On-Erase request to port 0xFF00
..............
Drive returned Status 0xD0
....................
Device Intro failed!
Sending Lite-On-Erase request to port 0xFF00
..............
Drive returned Status 0xD0
...............
Serial flash found with Status 0x72
Manufacturer ID: 0xC2
Device ID: 0x11
Flash Name: MXIC(MX25L2005)
Flash Size: 262144 bytes
Getting Status from port 0xFF00
SPi flash found with Status 0x72
Sending Chip Erase to Port 0xFF00
Erasing:............
Writing target buffer to flash
Writing Bank 0: ................
Writing Bank 1: ................
Writing Bank 2: ................
Writing Bank 3: ................
Flash Verification Test !
Reading Bank 0: ................
Reading Bank 1: ................
Reading Bank 2: ................
Reading Bank 3: ................
Write verified OK !
Sending Vendor Outro to port 0xFF00
After Outro, Jungleflasher only reads the drive if i power cycle. The dashboard loads up fine. However the drive won't open, that annoying green light is still blinking, and the dashboard is stuck on opening drive
|
|
daoliveri
Newbie
|
16. August 2010 @ 23:36 |
Link to this message
|
|
also...if this makes a difference...this console was a refurb that i got from best buy
|
Senior Member
|
17. August 2010 @ 05:28 |
Link to this message
|
|
So you can eject while flashing...that is, getting into half-tray position?
"All drives should be updated to Lite Touch + (LT+) firmware if playing on XBOX live. Samsung drives and pre-78/79 Hitachi drives do not utilize AP 2.5. All other drives are considered to be detectable by Microsoft (YMMV). Make sure all rips are ABGX verified, contain SSv2, and patched AP2.5 (where needed). XGD3 must currently be burned on new drive with PC Burner Max firmware for 100% rip. All modded consoles can be potentially unsafe for use on XBOX live."
|
|
peluynati
Senior Member
|
17. August 2010 @ 08:31 |
Link to this message
|
|
what you have is a stuck tray, when you eject and the light is flashing smack the top of the box a few times just over the drive it will pop right out. this is caused by many different things, the rubber band sometimes gets dried out, the tray is misaligned, or there is some debris in the casing that is causing it to get stuck, since it worked before you flashed, and not after i would look at how i put it back together, also check the magnate and make sure it is not stuck to the spindle.
|
|
daoliveri
Newbie
|
17. August 2010 @ 11:56 |
Link to this message
|
|
i can manually move the tray to whatever position it needs. After my first flash, however, it stopped working
|
|
peluynati
Senior Member
|
17. August 2010 @ 14:50 |
Link to this message
|
|
i think you should use a meter and check the trace cuts and make really sure you have them connected properly
|
|
Advertisement
|
|
|
|
daoliveri
Newbie
|
18. August 2010 @ 12:25 |
Link to this message
|
ok, so i dumped everything correctly. Is this a power problem? Everything is hooked up correctly. Is there a way to flash the original firmware of the drive and bring it back to stock? Will that at least give me a working xbox and let me reflash the drive? I don't believe the drive is broke because every once in a while i will power cycle and it will respond with opening or closing the drive. Other times it doesn't respond at all. I'm at a loss
|
|
