Mobile/PDA About Us Advertise here
User User name Password  
  Not registered yet? Register here.
Lost your password? Click here. 		 
  Home   News   Guides   Downloads   Glossary   Hardware   Profiles   Forums   v4  
 Advertise at AfterDawn.com     Link to us!     Private messages     Compose a private message     List of all updated threads     Threads without replies     Search messages
Sunday 24.8.2025 / 09:53
Search AfterDawn Forums:        In English   Suomeksi   På svenska
afterdawn.com > forums > consoles > xbox 360 - modding & hacking > 93450c jungle flasher issue
Show topics
 
Forums
Forums
93450c Jungle Flasher Issue
  Jump to:
 
Posted Message
Dindi304
Suspended due to non-functional email address
_ 		18. August 2010 @ 04:49 _ Link to this message    Send private message to this user   
Alright so I have already modded one of these systems useing the ck3 + probe2 soderless kit so I know my set up is right but Im lost to why this one 93450 drive I have doesnt work. I got the key off of it in Jungle flasher and then after I went back and repaired the cuts useing a Circuit Writer pen the drive doesnt want to show up. I tryed all the tricks of turning it off and on but the drive just doesnt wana detect. Another note the drive also wont eject or respond to anything but does have power and does read when I used my multimeter on it. Any suggestions are greatly needed.


PS: To add to what I have tryed I removed all the glue. And was able to detect the drive again in JF useing the probes. I flashed it and then again after repairimg it with the glue I get no drive detected or drive action.
[ + quote]

This message has been edited since posting. Last time this message was edited on 18. August 2010 @ 05:22
Advertisement
_ 		__
peluynati
Senior Member
_ 		18. August 2010 @ 09:14 _ Link to this message    Send private message to this user   
there are 3 fuses on that board i would suggest that you check each one of them to make sure one has not blown, also check your trace repairs and make sure they are not grounding out.
[ + quote]
MrGreaser
Senior Member
_ 		18. August 2010 @ 10:09 _ Link to this message    Send private message to this user   
Originally posted by peluynati:
 there are 3 fuses on that board i would suggest that you check each one of them to make sure one has not blown, also check your trace repairs and make sure they are not grounding out.
peluynati, what fuses are you speaking of? Diagram?
[ + quote]
"All drives should be updated to Lite Touch + (LT+) firmware if playing on XBOX live. Samsung drives and pre-78/79 Hitachi drives do not utilize AP 2.5. All other drives are considered to be detectable by Microsoft (YMMV). Make sure all rips are ABGX verified, contain SSv2, and patched AP2.5 (where needed). XGD3 must currently be burned on new drive with PC Burner Max firmware for 100% rip. All modded consoles can be potentially unsafe for use on XBOX live."
Dindi304
Suspended due to non-functional email address
_ 		18. August 2010 @ 10:20 _ Link to this message    Send private message to this user   
I dont understand what grounding out means what excatly am I looking for? What do I do to test that and if so how do I fix
[ + quote]
peluynati
Senior Member
_ 		18. August 2010 @ 12:30 _ Link to this message    Send private message to this user   
a short is grounded out, the fuses are not above the board there are in line fuses if you look on the board they have --->] a symbol similar to that.
[ + quote]
Dindi304
Suspended due to non-functional email address
_ 		18. August 2010 @ 19:28 _ Link to this message    Send private message to this user   
How to I fix that issue
[ + quote]
Modking30
AfterDawn Addict
_ 		18. August 2010 @ 20:21 _ Link to this message    Send private message to this user   
I see no mention of a multi meter. Did you even use one to check your traces?
[ + quote]
Dindi304
Suspended due to non-functional email address
_ 		18. August 2010 @ 23:42 _ Link to this message    Send private message to this user   
Originally posted by Modking30:
 I see no mention of a multi meter. Did you even use one to check your traces?

My first post said I used a multimeter. The full board has power after the glue. And yet it doesnt detect in JF. But everytime I remove the glue and probe it JF picks it right up. Im really at a loss. Is the glue not good enough maybe? But if thats true I dont understand why the glue worked on the last one. Any more ideas?
[ + quote]

This message has been edited since posting. Last time this message was edited on 18. August 2010 @ 23:43
Advertisement
_ 		__
 
_
peluynati
Senior Member
_ 		19. August 2010 @ 08:50 _ Link to this message    Send private message to this user   
what i would suggest is to do one trace with the glue, then try it in JF if it reads you know you have a problem with the other trace, does that make sense? it is obvious that one of the traces is getting grounded out, once you find which trace is causing the problem, then you can look closer into fixing the correct problem.
[ + quote]
afterdawn.com > forums > consoles > xbox 360 - modding & hacking > 93450c jungle flasher issue
 

Digital video: AfterDawn.com | AfterDawn Forums
Music: MP3Lizard.com
Gaming: Blasteroids.com | Blasteroids Forums | Compare game prices
Software: Software downloads
Blogs: User profile pages
RSS feeds: AfterDawn.com News | Software updates | AfterDawn Forums
International: AfterDawn in Finnish | AfterDawn in Swedish | AfterDawn in Norwegian | download.fi
Navigate: Search | Site map
About us: About AfterDawn Ltd | Advertise on our sites | Rules, Restrictions, Legal disclaimer & Privacy policy
Contact us: Send feedback | Contact our media sales team
 
  © 1999-2025 by AfterDawn Ltd.

  IDG TechNetwork