|
Kryptview A780
|
|
|
situl2005
Member
|
19. September 2010 @ 10:47 |
Link to this message
|
|
ok so I did factory default, rebooted box. did net scan, still comes up saying 1 already exists, etc slowly. Do i need the ethernet cable in when scanning?
|
|
Advertisement
|
|
|
|
AfterDawn Addict
3 product reviews
|
19. September 2010 @ 10:51 |
Link to this message
|
|
no you dont but you do need to be on direct feed no splitters on your cable
|
|
situl2005
Member
|
19. September 2010 @ 11:12 |
Link to this message
|
I tried direct feed, I've done exactly as you've said. factory default, reboot etc. It still says 1 already exist and slowly gets to 10 then only scans 11 channels, a few fta and a few sub channels which all appear to work. It seems box has got into some loop, where its not clearing the list of net id's. I.e after factory default, I assume the box clears memory of netId's etc. I'm totally lost as what to do now. The thing is I'm ordering more boxes for friends and I cannot recommend this box from my experience.
|
|
situl2005
Member
|
19. September 2010 @ 11:13 |
Link to this message
|
|
is there someway of doing a hard reset? i.e. removing an internal battery etc. I'm using version 3.6.
|
AfterDawn Addict
3 product reviews
|
19. September 2010 @ 11:19 |
Link to this message
|
|
when you are doing a full factory default do you then switch the box off at the back if not do that and then start again by what you are saying it seems to me that there is a problem with your cable feed or you are not scanning on your correct provider or you are trying to scan on ALL and not NETWORK
|
|
situl2005
Member
|
19. September 2010 @ 11:57 |
Link to this message
|
|
yes I do factory default, then switch it off and on again. Then go to auto scan select TW and press green button on network scan. This starts at 1 already exist, then goes upto 10 really slowly, then starts to scan and picks up only 11 channels. before I would get may be 1 exist then it would stream the net id and providers, but not now. I tried this without splitter using direct feed and with. It seems like something has bugged the box during power search mode. because as i said before some of the channel names have odd character eg. test 43 is now est 43 with t missing, also some have a % or ? or / where there should be a letter. I work with epos terminals and usually funny characters mean memory corruption. This could happen to others, so It may be worth speaking to developers, suppliers or contacts you know. This may be something that just happened to me, but what if this happens to others.
|
AfterDawn Addict
3 product reviews
|
19. September 2010 @ 12:01 |
Link to this message
|
|
ok could be a faulty box you have i suggest you contact supplier as i have not seen any other reports
|
|
situl2005
Member
|
19. September 2010 @ 12:25 |
Link to this message
|
I tried downgrading the box, but hasn't helped either. my supplier is mycable box, so I don't know if they would take it back with ver 3.2 firmware on it, unless I say it did it automatically during power search mode.
|
AfterDawn Addict
3 product reviews
|
19. September 2010 @ 12:35 |
Link to this message
|
|
why not try the box at a different house and see what happens
|
|
situl2005
Member
|
19. September 2010 @ 12:38 |
Link to this message
|
maybe I might try that, I don't suppose you know where I can get the fta firmware from?
|
AfterDawn Addict
3 product reviews
|
19. September 2010 @ 13:32 |
Link to this message
|
|
as far as i know there is none but i will have a look and see what i can find for you
|
|
BernieA
Newbie
|
19. September 2010 @ 17:03 |
Link to this message
|
I'm considering buying a KV780 to replace my now defunct Eurovox. Isn't it just a matter of time before Virmin or Sly block the websites which update Nags?
|
|
situl2005
Member
|
19. September 2010 @ 18:40 |
Link to this message
|
|
There are 4 pairs of pins board in the box, I wonder if putting a jumper on one of them might short it and reset the box, like in the jtag days
|
|
Advertisement
|
|
|
|
no1raj
Newbie
|
25. September 2010 @ 21:45 |
Link to this message
|
|
Hi all,
I just wanted to say that i've been rfeading various threads, and e45, u r the man!!!
You should be proud of urself cos ur always ready to help!!!
no1raj
|
