Originally posted by keter1234:

---

Originally posted by snag:

---

Originally posted by jerry52uk:

---

The Freq for Mansfield is 7550 or 7390 and the Symbolrate is 6952. Let me know if this has helped you to do the full scan. Regards

---

hi im from mansfield and have a dbox 1 that ? had all channels untill the kids messed it up, now no channels , can u help

thanks

---

hi ther just wondering if you got all your channel back on on yourdbox1 because iv got the same problom

---

Originally posted by gwapo:

---

Hi does anybody know where I can get the latest keys please?

I can't find them anywhere on this forum.

---

Originally posted by mgb17:

---

Originally posted by gwapo:

---

Hi does anybody know where I can get the latest keys please?

I can't find them anywhere on this forum.

---

http://forums.afterdawn.com/thread_view.cfm/531363

---

Originally posted by nad786:

---

hi i am a new meember on this forum i need some help on programming my funcard for my dbox 1 i still get the fta channels but the programmer it came with which i use to attach a nine volt battery to has nacked up so i decided to go back to the guy i bought it from cant find him i have bought a duolabs programmer and a new fun card 5 but need some help on programming the card i have read the thread by zappp64 but still need some help understandig it any help or an easier tut would be much appreciated!!
thanks nad
after reading the thread a gain i realised i need Any old version 4.3 6in1 flash and external EEP
5) ISVEdit for adding keys to the 6in1 external EEP file
can any one direct me to these thanks in advance nad

Originally posted by mgb17:

---

The theme of this thread is cable not satellite.
There is no chance to get sky via satellite without a sky box with valid card.

---

Originally posted by zappp64:

---

what you'll need is:

1) A DBOX1 with the cable tuner.
2) The Dr Jamal 2003 firmware loaded
3) The Irdeto cam patched with anon 5.4
4) Any old version 4.3 6in1 flash and external EEP
5) ISVEdit for adding keys to the 6in1 external EEP file
6) dvbedit for downloadin and uploading channel listings to/from the DBOX1
Getting a working card
---------------------
First of all you need to get the fun 6in1 hex version Flash4.3 (not 4.4 as it doesn't work so well) and any old EEP (external eeprom file) for 6in1 (one should come with the zip file). Do a search for xamuh or jettyboy 6in1 and you should get some hits. You also need the ISVEdit editor which you can get from google too.
1) Load the EEP hex into ISVEdit
2) Select Editor, then select the Nagra tab.
3) Check the boxes next to Provider 1, key 0 AND key 1. IT IS IMPORTANT THAT YOU DO THIS
4) Enter the current keys for your area into the Provider 1 key 0 and Key 1 boxes.
5) Click the Write To Memory button.
6) Click close
7) Save the hex file
Program a funcard with the Flash4.3 into the flash and the EEP file into the EXTERNAL eeprom. If you don't know how to do this then you won't get far I'm afraid.
You should now have a good 6in1 file to use in your dbox 1. Stick the card into it and leave it.
Finding/Getting the channels
---------------------------
1) You need to go into the tuner menu and do a search on each transponder frequency (There should be a services.xml file for the dbox2 that you can pick up the freqs and symbol rates for your area from. Simply enter the freq and symbol rate then hit 9 (search)
NB: Only the first 4 digits of the freq are entered i.e. 579.25MHz should be entered as 5792
2) Add any channels found on each frequency to the channel line up
3) Once you have searched all the transponders, save the channel list using dvbedit and a null modem lead to your PC. You can find dvbedit via google.
4) For each and every scrambled channel you need to do the following
a) Change to the channel
b) You now need to manually tell the DBOX1 to use the nagra EMM (1800) on each and every scrambled channel
When on the selected channel, go into the jamal menu to do an emm & ecm search. (Menu (blue) - C (Red) then 0, then 1 to select the emm - ecm pair.
Note that FTA channels do not need this and will give an error when you do an emm & ecm search, just leave the FTA as is and skip to the next channel.
c) You now need to replace the old channel with this new EMM one - Go to (Menu (blue) - 7 (PIDS) - A (YELLOW) - 3 (REPLACE)
(The reason you have to do this is that you cannot set (AFAIK) the jamal software to autodetect nagra EMMs (1800) it will only auto detect irdeto (0602) thus you have to force it to decode nagra EMM manually for each channel (total bummer)
5) Once you have done this for every scrambled channel download the list again using dvbedit and the null modem lead.
(You can then use this file for any other dbox that you want to use without going through this tortuous process again)
6) Rearrange your channel list on the PC using DVBedit then send it back to the dbox.
7) You should now have free tv!
Hopefully some members with old DBOX1s will find this useful.
Good Luck!
mrbmcg (Modshack)
Instructions for 9600 users only!:
**********************************
1. upload dvb2000 firmware to nokia (DVB1848K.bin)
2. Use either Dvbmem.exe or Vgrabber 7.7 to upload the subroutine file. (DVBK87.sbr)
3. use * Fun or Ds9 card
4. Make sure following are set within the channel lsitings PMT=Auto and PID's=Auto or you can manually set them via the "Pids menu" in dvbk.
NB. For those who donot have scsi connection, you can upload sbr files now via serial port using DVBmem.exe.
* Xamuh's and Satkoos file works very well with 6in1 cards
loading procedure:-
*******************
Upgrade Nokia software to DVBK.
First make sure that ur baudRate is set correctly in dvb2000.
On ur remote handset press following buttons:-
Guide(blue button)-->9"Expert Menu"-->A(Yellow)"General Setup"-->6 Com:38400 Baud And press OK to store
Make sure it is set to 38400, if it is not then press 6, this toggles through different baudrates.
Now check baudrate matches with DVBEdit software.. Open dvbedit-->File-->Preferances-->serialsetting-->speed-->38400
* Also set ur Comport here, depending on which serialport u wish to use Com1 or Com2.
Now we are ready to start:-
1. upload dvb2000 firmware to nokia (DVB1848K.bin) using DVBedit.
Open DVBedit -->serial-->Upgradefirmware-->"here find the folder where u stored the download file "DVB1848K.bin"
2. Upload the subroutine file. (DVBK90.sbr) using DVBedit
Open DVBedit -->serial-->Send subroutine-->"here find the folder where u stored the download file "DVBK90.sbr"
3. Program your Funcard with Xamuhs file

---

Originally posted by kolet123:

---

Originally posted by zappp64:

---

what you'll need is:


hi i have a nokia d box it possible to send it to you for upgrading
it sY NOT CHANAL FOUND ON THE SCREEN WHAT CAN DO?PLEASE HELP

1) A DBOX1 with the cable tuner.
2) The Dr Jamal 2003 firmware loaded
3) The Irdeto cam patched with anon 5.4
4) Any old version 4.3 6in1 flash and external EEP
5) ISVEdit for adding keys to the 6in1 external EEP file
6) dvbedit for downloadin and uploading channel listings to/from the DBOX1
Getting a working card
---------------------
First of all you need to get the fun 6in1 hex version Flash4.3 (not 4.4 as it doesn't work so well) and any old EEP (external eeprom file) for 6in1 (one should come with the zip file). Do a search for xamuh or jettyboy 6in1 and you should get some hits. You also need the ISVEdit editor which you can get from google too.
1) Load the EEP hex into ISVEdit
2) Select Editor, then select the Nagra tab.
3) Check the boxes next to Provider 1, key 0 AND key 1. IT IS IMPORTANT THAT YOU DO THIS
4) Enter the current keys for your area into the Provider 1 key 0 and Key 1 boxes.
5) Click the Write To Memory button.
6) Click close
7) Save the hex file
Program a funcard with the Flash4.3 into the flash and the EEP file into the EXTERNAL eeprom. If you don't know how to do this then you won't get far I'm afraid.
You should now have a good 6in1 file to use in your dbox 1. Stick the card into it and leave it.
Finding/Getting the channels
---------------------------
1) You need to go into the tuner menu and do a search on each transponder frequency (There should be a services.xml file for the dbox2 that you can pick up the freqs and symbol rates for your area from. Simply enter the freq and symbol rate then hit 9 (search)
NB: Only the first 4 digits of the freq are entered i.e. 579.25MHz should be entered as 5792
2) Add any channels found on each frequency to the channel line up
3) Once you have searched all the transponders, save the channel list using dvbedit and a null modem lead to your PC. You can find dvbedit via google.
4) For each and every scrambled channel you need to do the following
a) Change to the channel
b) You now need to manually tell the DBOX1 to use the nagra EMM (1800) on each and every scrambled channel
When on the selected channel, go into the jamal menu to do an emm & ecm search. (Menu (blue) - C (Red) then 0, then 1 to select the emm - ecm pair.
Note that FTA channels do not need this and will give an error when you do an emm & ecm search, just leave the FTA as is and skip to the next channel.
c) You now need to replace the old channel with this new EMM one - Go to (Menu (blue) - 7 (PIDS) - A (YELLOW) - 3 (REPLACE)
(The reason you have to do this is that you cannot set (AFAIK) the jamal software to autodetect nagra EMMs (1800) it will only auto detect irdeto (0602) thus you have to force it to decode nagra EMM manually for each channel (total bummer)
5) Once you have done this for every scrambled channel download the list again using dvbedit and the null modem lead.
(You can then use this file for any other dbox that you want to use without going through this tortuous process again)
6) Rearrange your channel list on the PC using DVBedit then send it back to the dbox.
7) You should now have free tv!
Hopefully some members with old DBOX1s will find this useful.
Good Luck!
mrbmcg (Modshack)
Instructions for 9600 users only!:
**********************************
1. upload dvb2000 firmware to nokia (DVB1848K.bin)
2. Use either Dvbmem.exe or Vgrabber 7.7 to upload the subroutine file. (DVBK87.sbr)
3. use * Fun or Ds9 card
4. Make sure following are set within the channel lsitings PMT=Auto and PID's=Auto or you can manually set them via the "Pids menu" in dvbk.
NB. For those who donot have scsi connection, you can upload sbr files now via serial port using DVBmem.exe.
* Xamuh's and Satkoos file works very well with 6in1 cards
loading procedure:-
*******************
Upgrade Nokia software to DVBK.
First make sure that ur baudRate is set correctly in dvb2000.
On ur remote handset press following buttons:-
Guide(blue button)-->9"Expert Menu"-->A(Yellow)"General Setup"-->6 Com:38400 Baud And press OK to store
Make sure it is set to 38400, if it is not then press 6, this toggles through different baudrates.
Now check baudrate matches with DVBEdit software.. Open dvbedit-->File-->Preferances-->serialsetting-->speed-->38400
* Also set ur Comport here, depending on which serialport u wish to use Com1 or Com2.
Now we are ready to start:-
1. upload dvb2000 firmware to nokia (DVB1848K.bin) using DVBedit.
Open DVBedit -->serial-->Upgradefirmware-->"here find the folder where u stored the download file "DVB1848K.bin"
2. Upload the subroutine file. (DVBK90.sbr) using DVBedit
Open DVBedit -->serial-->Send subroutine-->"here find the folder where u stored the download file "DVBK90.sbr"
3. Program your Funcard with Xamuhs file

---

---