|
dma on xp pro
|
|
AfterDawn Addict
|
15. February 2005 @ 09:34 |
Link to this message
|
|
i have just installed new pc,with xp sp2,i have ran a nero info tool check,and both dvd drives have dma enabled
but where else can i check this?
i am just finding my feet with xp,but cant find dma settings.
i am used to using windows2000 me,and found it no problem
with kinds regards from a stupid hursty
also can anyone tell me the difference with using nero's aspi layers from the conventional
|
|
Advertisement
|
|
|
|
AfterDawn Addict
|
15. February 2005 @ 12:07 |
Link to this message
|
|
It depends how you have the DVD drives connected, in your computer. But, for now, go the My Computer/Control Panel/System, then click on Hardware. Next, click on Device Manager and click on the + to the left of IDE ATA/ATAPI Controllers. Then, right click on Secondary IDE Channel, and select properties. Click on Advanced settings and look under Current Transfer mode. Both Device 0 and Device 1 should read Ultra DMA Mode 2. If one of your DVD drives is a Plextor 716A, it will show as Ultra DMA Mode 4.
Report back what you see.
Life is good!
GrandpaBruce - Vietnam Vet - 1970 - 1971
Computer: Intel Core i7-920 Nehalim;Asus P6T Deluxe V2
|
|
ScubaBud
AfterDawn Addict
|
15. February 2005 @ 12:35 |
Link to this message
|
|
For reference hursty:
My Burner is at Ultra DMA 4 (Asus DRW-1604P)
My DVD-Rom is at Ultra DMA 2 (Memorex)
|
AfterDawn Addict
|
16. February 2005 @ 09:03 |
Link to this message
|
|
spot on.cheers for that,both on ultra dma 2.
with kind regards hursty
|
|
ScubaBud
AfterDawn Addict
|
16. February 2005 @ 09:13 |
Link to this message
|
|
Great. So this new PC is a bit fast then your old one with the Crank on the side huh? :)
This message has been edited since posting. Last time this message was edited on 16. February 2005 @ 09:13
|
AfterDawn Addict
|
16. February 2005 @ 09:31 |
Link to this message
|
just a bit.hehe.........still havings problems connecting on AD though...
just having a few problems with security at the minute
still a few things i cannot do,like update dvd identifier,which is a pain.just bought 3 sorts of dvd and it wont recognize one of them.
not to mention lost most of my software installed in old pc.Nero restore is cobblers
with kind regards hursty
|
|
robtwilk
Member
|
16. February 2005 @ 17:06 |
Link to this message
|
|
GrandpaBW - why just the secondary IDE channel? I have always done the primary and secondary - Am I doing too much work?
|
|
ScubaBud
AfterDawn Addict
|
16. February 2005 @ 19:01 |
Link to this message
|
|
robtwilk
Your optical drives are usually on the Secondary Channel.
|
AfterDawn Addict
|
17. February 2005 @ 05:22 |
Link to this message
|
|
robtwilk, ScubaBud is correct. The opticals SHOULD be on the Secondary Channel.
Life is good!
GrandpaBruce - Vietnam Vet - 1970 - 1971
Computer: Intel Core i7-920 Nehalim;Asus P6T Deluxe V2
|
|
robtwilk
Member
|
17. February 2005 @ 07:35 |
Link to this message
|
|
Currently my primary has device 0 at Ultra DMA 5. My secondary has device 0 and 1 both at Ultra DMA 2.
What does the primary channel handle? My hard drive?
|
|
ScubaBud
AfterDawn Addict
|
17. February 2005 @ 07:58 |
Link to this message
|
|
That's correct. Device 0 is always the first device and device 1 would be the second on that particular ribbon cable.
|
|
robtwilk
Member
|
17. February 2005 @ 08:44 |
Link to this message
|
|
"Niphilim" told me I should have one burner on the primary cable and the other on the secondary cable. That's if I want to use two burners in the same PC.
Is it possible to connect a DVD drive to the cable connecting the hard drive?
I will probably add another hard drive in the near future to upgrade from my current 250 gigs, so I can't see attaching my DVD drive to the primary cable.
What problems would arise if both burners were on the secondary IDE channel?
Thanks!!
|
AfterDawn Addict
|
17. February 2005 @ 13:02 |
Link to this message
|
|
Nephilim would only say this if both burners were the same make and model, I think.
No way would you want a burner slaved to the same IDE channel as your hard drive. You hard drive performance would take a big hit.
If your hard drives are SATA, then your primary IDE channel would be free for other things like burners.
Life is good!
GrandpaBruce - Vietnam Vet - 1970 - 1971
Computer: Intel Core i7-920 Nehalim;Asus P6T Deluxe V2
This message has been edited since posting. Last time this message was edited on 17. February 2005 @ 13:04
|
|
ScubaBud
AfterDawn Addict
|
18. February 2005 @ 03:58 |
Link to this message
|
Actually Niphilim was correct when he told you that you can add a optical to a HD IDE, without suffering any speed loss, since this depends on your MB chip being able to support independent device timing along with the devices you will be using.
http://www.storagereview.com/guide2000/ref/hdd/if/ide/confTiming.html
Here is a good article written on the why's and how?s of setups/combinations. Many changes have been made to the tasking of IDE devices and chips that control them. I suggest you read it completely and then decide how you would like your PC to be setup today or for in the future. Be careful not to just read one paragraph and then not finish the page or article. Many things overlap each other.
Good luck :)
This message has been edited since posting. Last time this message was edited on 18. February 2005 @ 04:01
|
|
robtwilk
Member
|
18. February 2005 @ 14:32 |
Link to this message
|
|
GrandpaBW - I have an ultra ATA hard drive.
ScubaBud - I will read the link and see what sense I can make of the information - thanks!
Does this really matter if I just use my old burner (Sony DRU-700A) for playing movies and ripping DVDs? I would use the new drive as my burner.
|
|
ScubaBud
AfterDawn Addict
|
18. February 2005 @ 15:40 |
Link to this message
|
|
robtwilk
Since you stated that you will eventually add another HD to your system, just do what most do and leave your Primary for the HD's and the Secondary for the Optical drives. This might be, (will be,) less confusing since most are setup that way. Good luck either way.
|
|
robtwilk
Member
|
18. February 2005 @ 15:44 |
Link to this message
|
|
Yeah - that's where I'm headed. I'll give it a try and go from there. Thanks!
|
AfterDawn Addict
|
18. February 2005 @ 18:32 |
Link to this message
|
Quote:
Actually Niphilim was correct when he told you that you can add a optical to a HD IDE, without suffering any speed loss, since this depends on your MB chip being able to support independent device timing along with the devices you will be using.
http://www.storagereview.com/guide2000/ref/hdd/if/ide/confTiming.html
Here is a good article written on the why's and how?s of setups/combinations. Many changes have been made to the tasking of IDE devices and chips that control them. I suggest you read it completely and then decide how you would like your PC to be setup today or for in the future. Be careful not to just read one paragraph and then not finish the page or article. Many things overlap each other.
Good luck :)
Thanks for that link, ScubaBud. You can teach an old dog new tricks, afterall. I just learned something new. :)
Life is good!
GrandpaBruce - Vietnam Vet - 1970 - 1971
Computer: Intel Core i7-920 Nehalim;Asus P6T Deluxe V2
|
|
ScubaBud
AfterDawn Addict
|
19. February 2005 @ 02:15 |
Link to this message
|
|
You and me both GrandpaBW, you and me both!!!! :)
This message has been edited since posting. Last time this message was edited on 19. February 2005 @ 02:43
|
|
Advertisement
|
|
|
AfterDawn Addict
|
19. February 2005 @ 04:18 |
Link to this message
|
hi
yup never to old to learn! i have 2 burners on the primary master slave! always have - no probs here, i do have sata raid though a total of 6 drives! that tokk some fitting in my system! hehehe 1 HD is floating on wires! hehehe....
could do woth an 8 bay tower for my next mobo of dual raid! wow.......
Nothing here to see, move along folks.
 |
