|
Can't burn DL media w/ Nero, DVD Shrink or DVD Decrypter
|
|
AfterDawn Addict
|
29. July 2005 @ 13:08 |
Link to this message
|
i would beg to differ on the Memorex media~ :) the approach everyone here are taking is fairly close, i too have used DVD Decrypter iso read then iso write w/ no problems...when you THINK about the problem NOT lying with media, it USUALLY is the media that is the problem. :)
memorex media sucks and with the DL, their saga of poor media quality continues...as others have stated, try the Verbatim ones...the quality is FAR superior to the memorex, on sale, they are evenly matched in pricing..might as well go with the better one~
good luck
Recommended Media:
Taiyo Yuden 4x dvd-r TYGO1/ 8x dvd-r TYGO2/ 8x dvd+r YUDEN000T02/ 16x dvd+r YUDEN000T03
Verbatim 8x dvd+r MCC003
Verbatim dvd+r DL (MKM001)= flawless no compression backups
"Do Yourself A Favor, Use The Good Stuff
TY & Verbs 4 Life~ :)" ~docTY~
"Its better to be quiet and appear stupid, then to open your mouth and remove all doubt."
I am always prepared to recognize that there can be two points of view - mine and one that is probably wrong - John Gorton
|
|
Advertisement
|
|
|
|
AfterDawn Addict
|
29. July 2005 @ 16:43 |
Link to this message
|
If you ripped your files in iso read mode then just switch to iso write mode and burn your file. Arrow should be pointing at mode not tools.
This message has been edited since posting. Last time this message was edited on 29. July 2005 @ 16:44
|
|
Bruce999
Member
|
29. July 2005 @ 19:22 |
Link to this message
|
|
PRCOQUI:
>>>Are they able to copy without shrinking the movie so it will be 1.1 copy. <<<<
Correct. The reason some people are spending the additional cash to buy the more expensive dual layer discs is to avoid any compression (or shrinking) at all, which yields a backup copy that is identical in quality to the original.
These people may be in the minority, but some people are viewing their DVDs on very large screens, and the loss of quality that some users never notice suddenly becomes horrible when you magnify the picture to 65, or 93, or 110 inches. Added to this, some people are extremely picky about the quality of image, having been spoiled by viewing a lot of high definition television.
Hope this helps,
-Bruce
|
|
Bruce999
Member
|
30. July 2005 @ 21:52 |
Link to this message
|
|
PRCOQUI:
>>>>So why use a D/L 8.5. are you loosing the rest?<<<
No. Nothing is lost.
>>>Those program will shrink you copy.<<<<
Yes, the programs you mentioned will "shrink" the files, but this also means that they are reducing the quality of the picture, if the original was a dual layer commercial disc. And, the reduction is often noticable, and sometimes unacceptable, especially for some people.
>>>Are they able to copy without shrinking the movie so it will be 1.1 copy. <<<
Yes.
You might do a search on "dual layer" to get a better grasp on this.
-Bruce
|
Member
|
12. August 2005 @ 13:19 |
Link to this message
|
|
Dear friends I discovered (at least I hope) the correct way to make full copies (unfortunatelly) from the original one's. I'm using clone DVD with anuDVD running in yhe backround for making the .iso images and then with the same tool burn the dvd's with this method i dropped one out of five dl fiscs since now (bad media prompted from clone DVD). Since now I could'nt find a way to reauthor the compilation, such as dropping menus and extras which I don't have to see them over and over again since they are already in the original. And/or combine more movies on the same dl disc.
|
|
ACMaveric
Newbie
|
17. December 2005 @ 12:52 |
Link to this message
|
Hey all,
Here is my method with DVDShrink:
***Don't Compress, Re-Author to get 100%***
1. Cold Boot.
2. Disable AntiVirus and Network Connection.
3. Rip disc - When you hit Backup, Select ISO Image from Drop-Down.
4. Reboot.
5. Disable AntiVirus and Network Connection.
6. Open Nero, Select Open, then Select Image.
7. Burn at HALF the speed the media is rated at.
This works well with both Single and Dual Layer.
|
AfterDawn Addict
|
17. December 2005 @ 16:12 |
Link to this message
|
Quote:
4. Reboot.
5. Disable AntiVirus and Network Connection
Just out of curiousity why are you rebooting between step 3 and 6 why not just burn with Nero after you have used Shrink?
This message has been edited since posting. Last time this message was edited on 17. December 2005 @ 16:13
|
Member
|
18. December 2005 @ 02:49 |
Link to this message
|
I have not produced any more double layer coasters since I used:
(1). Verbatim or Philips +R DL discs.
(2). Writting in 2.4X usually (which is the certified) or 4X speed and never at maximum.
(3). Using CloneDVD which removes successfully the layer break of the source disc(s).
Theese are my suggestions only!
|
|
qid
Newbie
|
19. December 2005 @ 02:06 |
Link to this message
|
|
Well it is always good to burn disks (for music/movies) at the lower speeds. If burning the data disks max is ok....[Experts says it not me ;)]
|
|
ACMaveric
Newbie
|
19. December 2005 @ 09:23 |
Link to this message
|
|
I reboot to clear RAM.
I have noticed multiple times that I get much better results by 1. Disabling the Network and 2. Disabling AntiVirus.
Lastly, after I Rip the DVD I then Reboot for the Burn.
I suppose I am especially paranoid with the Dual Layer media since it is still around $2+ a Disc.
My Puter is an old Athlon 2000+ with a Gig of PC 2100 RAM; of course it would help to get a new computer.
|
|
edzo77
Newbie
|
4. February 2006 @ 16:49 |
Link to this message
|
I have a LG burner and I too am having problems burning DL discs.
This is the sequence of messages I get.
Generating DVD high compatibility borders
Session Fixation error
G: HL-DT-ST DVDRAM GSA-4163B
Could not perform end of Disc-at-once
Burn process failed at 2.4x (3.324 kb/s)
I'm using Nero 7.0.1.4
Ridata DVD+R DL discs, I have 4 beautiful coasters.
I'm not looking forward to a set of 6.
Any help or idea will be appreciated.
I have had varying failures. Some half burn, some fail to close disc,
some at the start.
I use DVD Shrink to rip DVD to HD and Nero to burn.
Firmware is latest.
|
AfterDawn Addict
|
5. February 2006 @ 04:12 |
Link to this message
|
|
|
ACMaveric
Newbie
|
5. February 2006 @ 08:40 |
Link to this message
|
|
edzo77,
This is the most important:
1. Cold Boot.
2. Disable AntiVirus & Network Connection.
3. Burn at HALF the Speed the Media is Rated at(or Slower).
4. ***Choose ISO from the Drop-Down in DVDShrink.*** (You will see this Option when you hit BackUp.)
What kind of Computer do you have?
|
|
dr_no
Member
|
5. February 2006 @ 11:50 |
Link to this message
|
edzo77,
Here is some good advice for you.
For DL media, Verbatim is the only one I can recommend.
For burning, if possible try ImgBurn from an ISO file, Nero is not the best handling the layer break.
|
|
qid
Newbie
|
6. February 2006 @ 03:28 |
Link to this message
|
|
|
Member
|
6. April 2006 @ 18:18 |
Link to this message
|
|
Today I was having a problem with ridata dl dvd-r and I found out by upgrading my firmware on my nec 3550a, I solved the problem. It might be worth checking, to see if their are any updates out there. Try cdfreaks and see if they have any upgrades.
This message has been edited since posting. Last time this message was edited on 6. April 2006 @ 18:19
|
|
jimdabo
Inactive
|
7. April 2006 @ 03:40 |
Link to this message
|
Hi, im having problem burning a dvd i copied to my computer today with DVD Decrypter. My dvd burner is a Samsung TS-H552B and the dvd is a 2 disk set they are both about 7Gb each disk. I tried alchohol 120% and DVD Decrypter to burn it to disk but it says not enough space (obviousl). Are both disks duel layer? If so how can i burn it or split the files and burn to 2 dvd's?
ps. my blank dvd's are TDK DVD-R 4.7Gb single sided.
|
|
Advertisement
|
|
|
AfterDawn Addict
|
7. April 2006 @ 03:59 |
Link to this message
|
|
