|
Please help. Cannot burn ANYTHING anymore.
|
|
|
msb1981
Newbie
|
20. August 2005 @ 20:25 |
Link to this message
|
|
Ok here's the deal, I know what I'm doing with computers. I work at a computer repair shop, but this problem has me stumped. It started a few months ago when I started having troubles burning CDs and DVDs. Well eventually I re-installed windows (xp pro) and installed a copy of Ubuntu Linux. Well I can rarely successfully burn a disc (CD or DVD, with either of my burners) in either XP or Linux. I have checked the IDE cables, I even replaced them. My burners (CD-RW and DVD+RW) both have their jumpers set correctly and both OSs are identifying them correctly. I have tried changing media, changing burn speed, changing every option available in almost every burning software out there, and still nothing. I have defragged my hard disks, changed the burning software's temporary cache location. There is nothing wrong with the operating systems, nothing wrong with the burners, and nothing wrong the the burning software, but I still have a problem.
When I try to burn it messes up different every time. Some times it looks as if the whole disc is burnt successfully, but then you turn the disc over and nothing is written on it! And the OSs still say they're blank. Other times they get to about 94% then have a write error, other times it's a write error right away. Other times the machine just locks up completely (and I do mean completely locks up, both in Windows and Linux) There is no pattern to the madness, and as far as I can tell NOTHING is wrong, yet it's only about 1 out of every 10 tries that I can actually burn a CD or DVD.
Please guys if you can think of anything I would appreciate it, but as far as I can tell everyone is working perfectly.My burners both used to burn perfectly even on cheap media at maximum speed, now I can crank out only coasters at minimum burn speed. Please what is wrong?
|
|
Advertisement
|
|
|
|
|
ddp
Moderator
|
20. August 2005 @ 20:40 |
Link to this message
|
|
is your dma enabled??
|
|
msb1981
Newbie
|
20. August 2005 @ 20:45 |
Link to this message
|
|
yes dma is enabled, I tried disabling with the same results.
|
|
ddp
Moderator
|
20. August 2005 @ 20:50 |
Link to this message
|
|
can you try the drives on another computer to see if the problem follows or not. also try another psu to see what happens.
|
|
msb1981
Newbie
|
20. August 2005 @ 20:56 |
Link to this message
|
|
i assume when you say psu you mean power supply? correct?
I don't have any other computers around here that are modern enough to be capable of burning a CD.
|
|
ddp
Moderator
|
20. August 2005 @ 21:01 |
Link to this message
|
|
power supply yes. right now it could be the motherboard causing the problem or the psu & unlikely both drives tho.
|
|
msb1981
Newbie
|
20. August 2005 @ 21:17 |
Link to this message
|
|
think there is any way of just testing the secondary IDE of the motherboard since I don't really have any other computer to try them in right now?
|
|
ddp
Moderator
|
20. August 2005 @ 21:24 |
Link to this message
|
|
disconnect 1 drive at a time to see what happens in burning. try putting either the cd burner or dvd burner as slave to the hd. switch the drives around so that the burners are on ide1 & the hd is on ide2.
|
|
msb1981
Newbie
|
23. August 2005 @ 11:10 |
Link to this message
|
|
well I haven't tried switching primary and secondary IDEs yet, but I just hooked up my CD-RW burner only. And the same thing happens. It says it burns successfully, and it reads regular CDs just fine, but when I close the drive after the burn the newly burnt CD shows up as blank.
One quick question, is there a specific windows service that needs to be enabled for CD burning to work properly? I optimized my system by disabling lots of services that were uneeded, and I checked on them fairly well. Also this would not explain why burning a CD locks up linux.
(As a side not I just opened Nero and did Disc Info, it showed up with one session that was open, I tried to close the session and got a disc fixation error at the end. The one error that seems to happen the most often throughout all of this is that the burning process messes up with the fixation. What can I do to fix this?)
This message has been edited since posting. Last time this message was edited on 23. August 2005 @ 11:19
|
Moderator
|
23. August 2005 @ 12:12 |
Link to this message
|
Ddp asked me to have a look at this one. have read the thread, and good to see you've tried something different, ie linux, to try and sort this.
However I'm guessing bad media, possibly old firmware, but sounds like a puzzler. How 'bout posting last section of your Nero log, its in c:\program files\ahead\nero\nerohistory.log. Do not post your derial number which usually begins with 1a21 or similar.
Main PC ~ Intel C2Q Q6600 (G0 Stepping)/Gigabyte GA-EP45-DS3/2GB Crucial Ballistix PC2-8500/Zalman CNPS9700/Antec 900/Corsair HX 620W
Network ~ DD-WRT ~ 2node WDS-WPA2/AES ~ Buffalo WHR-G54S. 3node WPA2/AES ~ WRT54GS v6 (inc. WEP BSSID), WRT54G v2, WRT54G2 v1. *** Forum Rules *** |
|
PJ2U2
Suspended due to non-functional email address
|
23. August 2005 @ 12:37 |
Link to this message
|
|
I do Electronics and computer repair as well. Sometimes the most simple thing gets by us. I had something similar once , the discs were bad. Let us know when you find it.
|
|
msb1981
Newbie
|
23. August 2005 @ 12:53 |
Link to this message
|
Don't worry if I ever get this sorted out I'll be sure to let everyone know how I did it.
An update, I finally upgraded the firmware on my DVD+RW and tried to burn a DVD, burn went fine (although nero kept mis-reporting the remaining time and the drive's buffer jumped around a LOT). When I put the disc into my player, nothing, back into my DVD+RW drive, nothing. It doesn't pop up the blank disc thing, but nothing is on it.
Here is a link to my nero history log, serial # has been removed, and it shows several attempts including some that were suppossedly successful and some that were unsuccessful.
http://cajunads.panicnow.net/nerohistory.log.txt
This message has been edited since posting. Last time this message was edited on 23. August 2005 @ 12:54
|
Moderator
|
23. August 2005 @ 12:57 |
Link to this message
|
|
That link domt work, paste the log here...
Main PC ~ Intel C2Q Q6600 (G0 Stepping)/Gigabyte GA-EP45-DS3/2GB Crucial Ballistix PC2-8500/Zalman CNPS9700/Antec 900/Corsair HX 620W
Network ~ DD-WRT ~ 2node WDS-WPA2/AES ~ Buffalo WHR-G54S. 3node WPA2/AES ~ WRT54GS v6 (inc. WEP BSSID), WRT54G v2, WRT54G2 v1. *** Forum Rules ***
|
|
msb1981
Newbie
|
23. August 2005 @ 13:08 |
Link to this message
|
|
try now, the link is working fine for me. I didn't want to paste it here since it's REALLY big.
|
Moderator
|
23. August 2005 @ 13:28 |
Link to this message
|
from last section of your logfile -
Quote:
DiskPeripheral : IBM-DPTA-371020 atapi Port 0 ID 0 DMA: On
DiskPeripheral : WDC WD1600JB-00EVA0 atapi Port 0 ID 1 DMA: On
CdRomPeripheral : DVD+R/RW DX082D atapi Port 1 ID 0 DMA: Off
- DMA's falled off again..
Quote:
Last possible write address on media: 2295103 (510:01.28, 4482MB)
Last address to be written: 2286020 (508:00.20, 4464MB)
- for info, you're burning to outer edge of disc, should set target size to 4300MB to stay away from edge of disc
Quote:
Recorder: DVD+R/RW DX082D, Media type: DVD+R
- burner isn't recognising the media correctly. the latest firmware's on there now but the firmware is about a year old, so can't recognise this media correctly
Main PC ~ Intel C2Q Q6600 (G0 Stepping)/Gigabyte GA-EP45-DS3/2GB Crucial Ballistix PC2-8500/Zalman CNPS9700/Antec 900/Corsair HX 620W
Network ~ DD-WRT ~ 2node WDS-WPA2/AES ~ Buffalo WHR-G54S. 3node WPA2/AES ~ WRT54GS v6 (inc. WEP BSSID), WRT54G v2, WRT54G2 v1. *** Forum Rules ***
|
|
msb1981
Newbie
|
23. August 2005 @ 13:39 |
Link to this message
|
well if it's from the last section of the logfile it should be from before I disabled DMA to flash the drive with the new firmware. So do you think that means it's an error or something?
And as for your last comment I don't understand. It says media type: DVD+R, I am using DVD+R discs, so how would that be not recognizing the media properly. I don't think I understood you on this part.
|
Moderator
|
23. August 2005 @ 13:47 |
Link to this message
|
Trust me I know my Nero logs. There should be 3 lines for the media description, you only have that one line so your media is too new for the burners firmware to rwcognise. I can't use the pc just yet to paste you an example as I'm burning a dvd. Am having to use my handheld to reply for now
Main PC ~ Intel C2Q Q6600 (G0 Stepping)/Gigabyte GA-EP45-DS3/2GB Crucial Ballistix PC2-8500/Zalman CNPS9700/Antec 900/Corsair HX 620W
Network ~ DD-WRT ~ 2node WDS-WPA2/AES ~ Buffalo WHR-G54S. 3node WPA2/AES ~ WRT54GS v6 (inc. WEP BSSID), WRT54G v2, WRT54G2 v1. *** Forum Rules ***
|
|
msb1981
Newbie
|
23. August 2005 @ 13:49 |
Link to this message
|
|
ah ok, well I've upgraded my firmware, so how would I tell if it's being recognized right now?
|
Moderator
|
23. August 2005 @ 14:04 |
Link to this message
|
here's an example of one of my media -
Quote:
Recorder: SONY DVD RW DRU-700A, Media type: DVD-R
Disc Manufacturer: MCC 02 - RG20
Disc Application Code: 64, Disc Physical Code: 193
- fully recognised thus it can use the disc correctly.
programs such as this will show more info about media - http://www.afterdawn.com/software/video_software/dvd_tools/dvd_id...
..but basically that particular disc just isn't gonna play ball properly cus the firmware in the burner is effectively out if date by a year. it happens, drives get left behind when companies bring out new ones.
...i am simply reportingf what i see in the logfile..
..just found snippet of log for a cd - Quote:
Recorder: DVD+R/RW DX082D;
CDR code: 00 97 26 11; OSJ entry from: POSTECH Corporation
ATIP Data:
Special Info [hex] 1: F0 00 B8, 2: 61 1A 0B (LI 97:26.11), 3: 4F 3B 49 (LO 79:59.73)
Additional Info [hex] 1: 00 00 00 (invalid), 2: 00 00 00 (invalid), 3: 00 00 00 (invalid)
- that's not fairing much better..
Quote:
Sense Key: 0x03 (KEY_MEDIUM_ERROR)
Write error
- burner don't like that disc either..
Main PC ~ Intel C2Q Q6600 (G0 Stepping)/Gigabyte GA-EP45-DS3/2GB Crucial Ballistix PC2-8500/Zalman CNPS9700/Antec 900/Corsair HX 620W
Network ~ DD-WRT ~ 2node WDS-WPA2/AES ~ Buffalo WHR-G54S. 3node WPA2/AES ~ WRT54GS v6 (inc. WEP BSSID), WRT54G v2, WRT54G2 v1. *** Forum Rules ***
|
|
msb1981
Newbie
|
23. August 2005 @ 14:36 |
Link to this message
|
|
I guess I misunderstood. I thought the part of the logfile you got that info from was old. I just updated the firmware a few hours ago. I updated it from 0.89 to 1.50
|
|
msb1981
Newbie
|
23. August 2005 @ 17:49 |
Link to this message
|
|
allright with the firmware update, DMA turned off, and IMAPI service re-enabled I can now burn CD-Rs ok, but the DVDs still don't want to work. I just burned one that claimed to be successful, but when I stick it back in the drive it doesn't even read there's a disc in it.
|
|
kickbak
Junior Member
|
23. August 2005 @ 20:44 |
Link to this message
|
|
Are you using the default drivers for the IDE ata/atapi controllers?
|
Moderator
|
23. August 2005 @ 21:45 |
Link to this message
|
@kickbak -
Quote:
Recorder: <DVD+R/RW DX082D> Version: 11SB - HA 1 TA 0 - 6.6.0.8
Adapter driver: <atapi> HA 1
Drive buffer : 8192kB
Bus Type : default (0) -> ATAPI, detected: ATAPI
CD-ROM: <DVD+R/RW DX082D >Version: 11SB - HA 1 TA 0 - 6.6.0.8
Adapter driver: <atapi> HA 1
=== Scsi-Device-Map ===
DiskPeripheral : IBM-DPTA-371020 atapi Port 0 ID 0 DMA: On
DiskPeripheral : WDC WD1600JB-00EVA0 atapi Port 0 ID 1 DMA: On
CdRomPeripheral : DVD+R/RW DX082D atapi Port 1 ID 0 DMA: On
File 'Drivers\atapi.sys': Ver=5.1.2600.2180 (xpsp_sp2_rtm.040803-2158), size=95360 bytes, created 8/3/2004 11:59:44 PM (Adapter driver for rec)
- yes he is...
@msb1981 - you need to try a blank dvd that your burner can recognise, or try a more well known burner, or a newer (well known) burner
Main PC ~ Intel C2Q Q6600 (G0 Stepping)/Gigabyte GA-EP45-DS3/2GB Crucial Ballistix PC2-8500/Zalman CNPS9700/Antec 900/Corsair HX 620W
Network ~ DD-WRT ~ 2node WDS-WPA2/AES ~ Buffalo WHR-G54S. 3node WPA2/AES ~ WRT54GS v6 (inc. WEP BSSID), WRT54G v2, WRT54G2 v1. *** Forum Rules ***
This message has been edited since posting. Last time this message was edited on 23. August 2005 @ 21:45
|
|
kickbak
Junior Member
|
24. August 2005 @ 10:42 |
Link to this message
|
It wouldn't hurt to get the latest firmware 150B
http://forum.rpc1.org/dl_file.php?site=firmx&file=Dx82150b.zip
There is also a pathched RPC1 firmware by "The Dangerous Brothers"
http://tdb.rpc1.org/#DX082
I have had problems with Cyberdrives being bad right out of the box.
I returned two Cyberdrives (made in china).
The third was a Cyberdrive "Made in Malaysia". It turned out to be a rebadged BenQ DW800a.
I only buy Benq and NEC drives now.
This message has been edited since posting. Last time this message was edited on 24. August 2005 @ 10:50
|
|
Advertisement
|
|
|
|
msb1981
Newbie
|
24. August 2005 @ 11:32 |
Link to this message
|
|
the firmware upgrade I did yesterday is 150B, it seemed to allow me to burn CDs just fine. Just still having problems with it burning "blank" DVDs.
This message has been edited since posting. Last time this message was edited on 24. August 2005 @ 11:35
|
