|
Windows ME
|
|
Member
|
24. September 2005 @ 13:50 |
Link to this message
|
|
im doing a clean install of Windows ME on an older computer and i need to burn the cab files that are on its hard drive to a cd. but i dont have a cd burner on that computer. could i take the hdd out and put it in my computer with a burner? then burn them from there?
|
|
Advertisement
|
|
|
|
AfterDawn Addict
|
24. September 2005 @ 14:07 |
Link to this message
|
|
Yes you can, but make sure that it is on the secondary ide connection on the other computer, or change the jumper to make it a slave to the OS drive on the other computer.
Life is good!
GrandpaBruce - Vietnam Vet - 1970 - 1971
Computer: Intel Core i7-920 Nehalim;Asus P6T Deluxe V2
|
Member
|
24. September 2005 @ 18:58 |
Link to this message
|
|
ok...so i have booted the comp. in dos mode and formated the HDD but when i go to type E:\setup it says "CDR101: not ready reading drive E abort, retry, fail?" what do i do
This message has been edited since posting. Last time this message was edited on 24. September 2005 @ 19:16
|
|
ddp
Moderator
|
24. September 2005 @ 19:03 |
Link to this message
|
|
can you see the files of me on your posting computer??
|
Member
|
24. September 2005 @ 19:17 |
Link to this message
|
|
the CAB files.....yes i have the folder on this computer (my posting computer)
|
Member
|
24. September 2005 @ 19:25 |
Link to this message
|
|
i dont know if this matters but i did not burn the cab files in any kind of iso or anything i just draged and droped using roxio drag to disc
|
|
ddp
Moderator
|
24. September 2005 @ 19:27 |
Link to this message
|
|
but on the other hd that is to get the me, is it on that hd or on a cd?? if on the hd on the other computer & the hd is bootable than why type e\:setup when it should c\:me\setup with me being the folder with all the cab files needed to load me.
|
Member
|
24. September 2005 @ 19:31 |
Link to this message
|
|
the HDD that is to recive ME is blank...i formated it in DOS and i took the cab files before i formated the HDD and burned them to a CD
so now im trying to use the floppy boot disc and the CD with the cab files so i can install ME on the blank HDD.
(all i did to make the cabs cd was drag and drop the cabs files directly to a cd..so it is olny E:\cabs there is no windows or any other folder before the cabs folder)
PS. i checked to see if the SETUP.EXE file was there in the cabs folder and it is.
This message has been edited since posting. Last time this message was edited on 24. September 2005 @ 19:53
|
|
ddp
Moderator
|
24. September 2005 @ 20:07 |
Link to this message
|
|
when booting off the me bootdisk, can you see the files on the cd? are you using a cdrw disk instead of cdr as that might be why you got the cdr101 error?
|
Member
|
24. September 2005 @ 20:11 |
Link to this message
|
|
i have the cab files that i burnt backed up on another computer that is how i see them and what i burnt. i am using a TDK CD-R
|
AfterDawn Addict
|
24. September 2005 @ 21:27 |
Link to this message
|
|
You may have made a dreadful mistake using D2D to burn those cab files. Possibly not, but you should have used Creator Classic to do it, not D2D or any other packet writing software. Packet writing software is unreliable, at best.
If you have those files on another computer, burn another CD, using Creator Classic. I would bet that you see the CD drive in DOS.
Life is good!
GrandpaBruce - Vietnam Vet - 1970 - 1971
Computer: Intel Core i7-920 Nehalim;Asus P6T Deluxe V2
|
Member
|
25. September 2005 @ 12:53 |
Link to this message
|
|
ok...i have went through all the steps to install windows ME...but when i restart the computer it goes to the loading screen for ME but then gives me three error mesages:(
#1 is "error loading explorer.exe you must reinstall windows"
#2 is "the shell32.dll file linked to missing export comctl
32.dll:388."
#3 is "kernel 32 has caused an error in krnl386.exe kernel 32. will now close"
|
|
Advertisement
|
|
|
|
ddp
Moderator
|
25. September 2005 @ 14:10 |
Link to this message
|
|
take a pencil eraser to the gold contacts of the ram to remove oxidation off them. remove all cards except for videocard. re-install me.
This message has been edited since posting. Last time this message was edited on 25. September 2005 @ 14:10
|
