|
win xp wont boot on PC i built.help
|
|
Member
|
27. September 2005 @ 23:39 |
Link to this message
|
|
I just finished putting together my computer.Everything went fine.But when i start it up it says insert boot cd.I inserted my win xp which i purchased a few hours ago and hit enter.The screen turned blue and win xp started to install.But then this message came up on the screen
error loading file \i386\ntkrnlmp.exe setup cannot continue
Someone help i want to use my new PC
|
|
Advertisement
|
 |
|
|
|
Rosco404
Suspended due to non-functional email address
|
28. September 2005 @ 02:19 |
Link to this message
|
|
is the disc an original? and is it clean?
Have you got more than one cd drive, if so try booting off the other one?
If not it could point to a hardware problem....
smoke me a kipper i'll be back for breakfast - Ace  |
Member
|
28. September 2005 @ 02:32 |
Link to this message
|
|
yes its original and clean.i tryed it in both drives.it also says error code 7 on the screen
|
|
Rosco404
Suspended due to non-functional email address
|
28. September 2005 @ 02:49 |
Link to this message
|
|
Hmmm..
Have you more than one stick of memory in?
To eliminate a memory problem... Try one stick in at a time...
For example.. If you have 2x 512mb ddr sticks, try one in and if it still gets an error take that out and try the other one...
smoke me a kipper i'll be back for breakfast - Ace |
Member
|
28. September 2005 @ 03:23 |
Link to this message
|
|
i have 2 512 mb.tryed exactly what you said still getting error 7 when trying to boot win xp
|
|
Rosco404
Suspended due to non-functional email address
|
28. September 2005 @ 03:29 |
Link to this message
|
|
It could be many things, but seems you have eliminated memory now....
Could be CPU? What CPU do you have? Do you have another of the same type?
smoke me a kipper i'll be back for breakfast - Ace |
Member
|
28. September 2005 @ 03:38 |
Link to this message
|
|
i have an AMD 64 3700+
ABIT KN8 mobo
Gainward geforce 6600 128mb
|
|
Rosco404
Suspended due to non-functional email address
|
28. September 2005 @ 04:07 |
Link to this message
|
|
To be honest it sounds like a hardware problem...
Im lucky as i own a computer company and can just swap and change parts untill i norow down the problem....
It could be a lot of things like i said before...
Did you buy your stuff from a local pc shop or online?
If you got it at a local shop see if they can test the CPU out for you... I see its a 939 pin chip, if you had another handy that would have been great, but i doubt you will?
smoke me a kipper i'll be back for breakfast - Ace |
Senior Member
|
28. September 2005 @ 06:45 |
Link to this message
|
|
Are you using an on-board vid card, or an agp/pci-x card? If you added another card, try installing using the only the on-board (remove the other). I would also strip down all unecessary hardware, still only use one mem stick (closest to the CPU), and also double check all ribbon cables to ensure that they are fully seated.
You can also get a win 98 boot disk, and copy the setup files (i386 folder) to the hdd. Leave the hdd formatted as fat32. Run setup from the hdd, and you should be OK. After install, open a cmd prompt and run "convert C: /fs:ntfs" to convert to ntfs. If you have errors while copying the cd to hdd, then the media could be bad. Try to get another cd from a friend or something, but make sure to use your own CD key for isntallation.
Hope this helps.
|
|
Rosco404
Suspended due to non-functional email address
|
28. September 2005 @ 10:22 |
Link to this message
|
Found this article on microsoft's site....
http://support.microsoft.com/default.aspx?scid=kb;en-us;812580
It gives you the cause and resolution... Try this stated in the article as you are installing a fresh install...
Quote:
3. When you receive the "Press F6 to load SCSI/Raid Drivers" prompt, press F7 to bypass Advanced Configuration and PowerInterface (ACPI) detection.
smoke me a kipper i'll be back for breakfast - Ace |
Member
|
28. September 2005 @ 23:20 |
Link to this message
|
|
what kind of hard rive are you trying to run? if it's sata then you need to enable it in bios and run drivers by pressing F6 on start up.It's probably trying to copy windows but cannot place it to the hard drive.Had kind of the same problem when I built mine.Try changing boot sequence in bios or check it.
Is it crap or is it memorex?
|
Member
|
29. September 2005 @ 04:18 |
Link to this message
|
|
Got it working.I took it all apart and put it back together and it worked.Thanks for all the help.
I have a question.I installed unreal tournament 2004 but cannot play it because direct3D acceleration is not enabled.I have installed all drivers.How do i fix this problom?
|
|
Advertisement
|
|
|
|
Rosco404
Suspended due to non-functional email address
|
29. September 2005 @ 06:41 |
Link to this message
|
smoke me a kipper i'll be back for breakfast - Ace |
