|
|
|
Burning problems
|
|
|
Kevthekev
Suspended due to non-functional email address
|
20. April 2006 @ 01:00 |
Link to this message
|
|
Hi
I wonder if anyone can provide me with some advice.
I have been copying DVDs with no problems for the last three months. From last week I cannot burn to DVD. My burner will read and write DVDs to my hard drive but I can no longer burn to dvd. Though I can still burn CDs. I use Decrypter and Shrink. I think my probles started when I tried to copy a scratched DVD which my drive stopped reading half way through - could this have damaged my lens?
Could I have a defective lens.
|
|
Advertisement
|
 |
|
|
AfterDawn Addict
|
20. April 2006 @ 03:18 |
Link to this message
|
It sounds more like a software issue to me. If you can still burn CD's there is nothing wrong with the burner. Make sure that the burn with DVDdecrypter ticked so that it will open dvddecrypter and commense the burn.
If it will not, try uninstalling and reinstalling the software programs, i.e. DVDdecrypter and shrink.
Possibly you got a corrupted file. You can get fresh downloads here:
http://mrbass.org/dvdrip/
http://mrbass.org/dvdshrink/
http://www.imgburn.com
Imgburn is the same burn engine as DVDdecrypter (updated) but not a ripper. I use it instead of DVDdecrypter to burn.
Cheers.
|
|
Kevthekev
Suspended due to non-functional email address
|
20. April 2006 @ 04:50 |
Link to this message
|
|
Cheers. I'll do that when I get home tonite. Thanks for the advice.
|
|
brobear
Suspended permanently
|
20. April 2006 @ 05:36 |
Link to this message
|
|
No mention of the sytems age or a brand and model for the burner. In case the software fix doesn't work; I had an older burner that went bad. It still reads, burns CDs and DVD RWs. It just won't write to DVD R. I replaced the drive and the new one works fine. Now I use a dual burner setup. If one starts acting funny, all I have to do is try the other to see if it's a hardware or software problem. Nowadays a decent burner costs little more than a ROM, unless a person wants one of the top end units. If you have one available, the easy check is to switch out the drive.
|
|
nemo101
Junior Member
|
20. April 2006 @ 08:21 |
Link to this message
|
|
I agree with brobear, I used to have a burner that after awhile decided it didn't like ripped media, with everything else it was fine.
After checking the software choices this maybe your next step.
|
|
Kevthekev
Suspended due to non-functional email address
|
20. April 2006 @ 12:10 |
Link to this message
|
Hi This is a log I received. Hope I'm not being too cheeky.
Can you Guys deduce anything from this?
Thanks again
Windows XP 5.1
IA32
WinAspi: -
ahead WinASPI: File 'C:\Program Files\Ahead\nero\Wnaspi32.dll': Ver=2.0.1.74, size=164112 bytes, created 26/10/2004 18:35:32
Nero Version: 6.6.0.8 (Nero Express)
Recorder: <FREECOM_ DVD+/-RW16H8> Version: FR00 - HA 2 TA 0 - 6.6.0.8
Adapter driver: <> HA 2
Drive buffer : 2048kB
Bus Type : via Inquiry data (1) -> ATAPI, detected: ?
Connected to MMC as unknown drive with class-nr : 1
Drive is autodetected - recorder class: Std. MMC recorder
CD-ROM: <HL-DT-ST CDRW/DVD GCC4482>Version: E107 - HA 0 TA 0 - 6.6.0.8
Adapter driver: <atapi> HA 0
=== Scsi-Device-Map ===
CdRomPeripheral : HL-DT-ST CDRW/DVD GCC4482 atapi Port 0 ID 0 DMA: On
DiskPeripheral : Maxtor 6L160M0 atapi Port 1 ID 0 DMA: On
=== CDRom-Device-Map ===
HL-DT-ST CDRW/DVD GCC448 D: CDRom0
FREECOM_ DVD+/-RW16H8 E: CDRom1
=======================
AutoRun : 1
Excluded drive IDs:
WriteBufferSize: 83886080 (0) Byte
ShowDrvBufStat : 0
BUFE : 0
Physical memory : 1022MB (1046604kB)
Free physical memory: 546MB (559408kB)
Memory in use : 46 %
Uncached PFiles: 0x0
Use Inquiry : 1
Global Bus Type: default (0)
Check supported media : Disabled (0)
19.4.2006
UDF/ISO compilation
19:17:21 #1 Phase 112 File dlgbrnst.cpp, Line 1832
DVD-Video files reallocation started
19:17:21 #2 Phase 114 File dlgbrnst.cpp, Line 1832
DVD-Video files reallocation completed (no file modified)
19:17:21 #3 Text 0 File Isodoc.cpp, Line 6172
Iso document burn settings
------------------------------------------
Determine maximum speed : FALSE
Simulate : FALSE
Write : TRUE
Finalize CD : TRUE
Multisession : FALSE
Burning mode : DAO
Mode : 1
ISO Level : 1 (Max. of 11 = 8 + 3 char)
Character set : ISO 9660
Joliet :FALSE
Allow pathdepth more than 8 directories : FALSE
Allow more than 255 characters in path : FALSE
Write ISO9660 ;1 file extensions : TRUE
19:17:21 #4 Phase 111 File dlgbrnst.cpp, Line 1832
DVD-Video files sorted
19:17:21 #5 Text 0 File Reader.cpp, Line 127
Reader running
19:17:21 #6 Text 0 File Writer.cpp, Line 122
Writer FREECOM_ DVD+/-RW16H8 running
19:17:21 #7 ISO9660GEN -11 File geniso.cpp, Line 3293
First writeable address = 0 (0x00000000)
19:17:22 #8 ISO9660GEN -11 File geniso.cpp, Line 3293
First writeable address = 0 (0x00000000)
19:17:22 #9 Text 0 File Burncd.cpp, Line 3153
Turn on Disc-At-Once, using DVD media
19:17:22 #10 Text 0 File DlgWaitCD.cpp, Line 259
Last possible write address on media: 2298495 (510:46.45, 4489MB)
Last address to be written: 2286111 (508:01.36, 4465MB)
19:17:22 #11 Text 0 File DlgWaitCD.cpp, Line 271
Write in overburning mode: NO (enabled: CD)
19:17:22 #12 Text 0 File DlgWaitCD.cpp, Line 2316
Recorder: FREECOM_ DVD+/-RW16H8, Media type: DVD-R
Disc Manufacturer: TTH02 -
Disc Application Code: 64, Disc Physical Code: 193
19:17:22 #13 Text 0 File DlgWaitCD.cpp, Line 433
>>> Protocol of DlgWaitCD activities: <<<
=========================================
19:17:22 #14 Text 0 File ThreadedTransferInterface.cpp, Line 830
Setup items (after recorder preparation)
0: TRM_DATA_MODE1 ()
2 indices, index0 (150) not provided
original disc pos #0 + 2286112 (2286112) = #2286112/508:1.37
relocatable, disc pos for caching/writing not required/ required, no patch infos
-> TRM_DATA_MODE1, 2048, config 0, wanted index0 0 blocks, length 2286112 blocks [FREECOM_ DVD+/-RW16H8]
--------------------------------------------------------------
19:17:22 #15 Text 0 File ThreadedTransferInterface.cpp, Line 1043
Prepare recorder [FREECOM_ DVD+/-RW16H8] for write in CUE-sheet-DAO
DAO infos:
==========
MCN: ""
TOCType: 0x00; Session Closed, disc fixated
Tracks 1 to 1:
1: TRM_DATA_MODE1, 2048/0x00, FilePos 0 0 4681957376, ISRC ""
DAO layout:
===========
__Start_|____Track_|_Idx_|_CtrlAdr_|_RecDep__________
0 | lead-in | 0 | 0x41 | 0x00
0 | 1 | 0 | 0x41 | 0x00
0 | 1 | 1 | 0x41 | 0x00
2286112 | lead-out | 1 | 0x41 | 0x00
19:17:22 #16 Phase 24 File dlgbrnst.cpp, Line 1832
Caching of files started
19:17:22 #17 Text 0 File Burncd.cpp, Line 4040
Cache writing successful.
19:17:22 #18 Phase 25 File dlgbrnst.cpp, Line 1832
Caching of files completed
19:17:22 #19 Phase 36 File dlgbrnst.cpp, Line 1832
Burn process started at 16x (22,160 KB/s)
19:17:22 #20 Text 0 File ThreadedTransferInterface.cpp, Line 2609
Verifying disc position of item 0 (relocatable, disc pos, no patch infos, orig at #0): write at #0
19:17:22 #21 Text 0 File DVDR.cpp, Line 2356
Recording mode: Sequential Recording Mode
19:17:22 #22 Text 0 File Mmc.cpp, Line 21206
Set BUFE: Buffer underrun protection -> ON
19:17:22 #23 Text 0 File DVDR.cpp, Line 2502
Start write address at LBA 0
DVD high compatibility mode: Yes
19:17:22 #24 Text 0 File Cdrdrv.cpp, Line 8442
---- DVD Structure: Physical Format Information (00h) ----
Layer: 0, Address: 0 (0 h), AGID: 0; Length: 2050
Book Type: DVD-R (2), Part Version: 5
Disc Size: 120 mm, Maximum Rate: <not specified> (F h)
Number of Layers: 1, Track Path: Parallel Track Path (PTP), Layer Type: recordable
Linear Density: 0,267 um/bit, Track Density: 0,74 um/track
Starting Physical Sector Number of Data Area: 30000 h (DVD-ROM, DVD-R/-RW, DVD+R/+RW)
End Physical Sector Number of Data Area: 0 h
End Sector Number in Layer 0: 0 h (LBN: FFFD0000 h, 4193920 MB)
Data in Burst Cutting Area (BCA) does not exist
Start sector number of the current Border-Out: 0 h
Start sector number of the next Border-In: 0 h
Media Specific [16..63]:
00 60 00 10 20 30 40 50 - 00 00 00 21 00 00 00 00 .`...0@P...!....
00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................
19:17:45 #25 Text 0 File Cdrdrv.cpp, Line 1287
19:17:45.234 - FREECOM_ DVD+/-RW16H8\H2 T0 : Queue again later
19:17:45 #26 SCSI -500 File Cdrdrv.cpp, Line 1435
SCSI Exec, HA 2, TA 0, LUN 0, buffer 0x0ABF0000
Status: 0x02 (0x03, SCSI_ABORTED)
HA-Status 0x10 (0x0A, SCSI_HASTAT_REQUEST_SENSE_FAILED)
TA-Status 0x00 (0x00, OK)
Sense Key: 0x05 (KEY_ILLEGAL_REQUEST)
Sense Code: 0x26
Sense Qual: 0x02
CDB Data: 0x2A 0x00 0x00 0x00 0x01 0xC0 0x00 0x00 0x20 0x00 0x00 0x00
Sense Data: 0xF0 0x00 0x05 0x00 0x00 0x00 0x00 0x00
0x00 0x00 0x00 0x00 0x26 0x02
19:17:50 #27 SCSI -1114 File Cdrdrv.cpp, Line 1435
SCSI Exec, HA 2, TA 0, LUN 0, buffer 0x0B270600
Status: 0x04 (0x01, SCSI_ERR)
HA-Status 0x00 (0x00, OK)
TA-Status 0x02 (0x01, SCSI_TASTATUS_CHKCOND)
Sense Key: 0x06 (KEY_UNIT_ATTENTION)
Sense Code: 0x29
Sense Qual: 0x00
CDB Data: 0x2A 0x00 0x00 0x00 0x01 0xC0 0x00 0x00 0x20 0x00 0x00 0x00
Sense Data: 0x70 0x00 0x06 0x00 0x00 0x00 0x00 0x0A
0x00 0x00 0x00 0x00 0x29 0x00
19:17:50 #28 CDR -1114 File Writer.cpp, Line 311
Reset occurred
19:17:50 #29 Text 0 File ThreadedTransfer.cpp, Line 228
all writers idle, stopping conversion
19:17:50 #30 Text 0 File ThreadedTransfer.cpp, Line 222
conversion idle, stopping reader
19:17:50 #31 Text 0 File DVDR.cpp, Line 2765
EndDAO: Last written address was 447
19:18:06 #32 CDR -1033 File WriterStatus.cpp, Line 167
Drive not ready
19:18:06 #33 TRANSFER -24 File WriterStatus.cpp, Line 167
Could not perform end of Disc-at-once
19:18:06 #34 Phase 38 File dlgbrnst.cpp, Line 1832
Burn process failed at 16x (22,160 KB/s)
Existing drivers:
File 'Drivers\ADPU160M.SYS': Ver=v3.60a (Lab01_N(johnstra).010529-2218), size=101888 bytes, created 17/08/2001 14:07:32
File 'Drivers\CDRALW2K.SYS': Ver=6.3.0.11 , size=24698 bytes, created 03/11/2004 17:54:46
File 'Drivers\PXHELP20.SYS': Ver=2.03.31a, size=20640 bytes, created 05/04/2005 03:03:00 (Prassi/Veritas driver for win 2K)
File 'Drivers\atapi.sys': Ver=5.1.2600.2180 (xpsp_sp2_rtm.040803-2158), size=95360 bytes, created 03/08/2004 22:59:44 (Adapter driver for src)
Registry Keys:
HKLM\Software\Microsoft\Windows NT\CurrentVersion\WinLogon\AllocateCDROMs : 0 (Security Option)
|
|
brobear
Suspended permanently
|
20. April 2006 @ 19:46 |
Link to this message
|
http://www.freecom.com/firmware.asp?form1=true&form2=true&serie=1...
Freecom has phone support as well as online support. The only model number I saw close to yours was a 16H9 and yours reads 16H8. Your firmware is FR00 and Freecom appears to have later versions, you may want to call on yours.
The Nero software version is a bit old, you may want to update that. I suggest 6.6.0.18 instead of the newer 6.6.1.4 which has caused some people trouble. Links have been posted around here somewhere. I went with Nero 7, but a lot of people are hanging on to the 6. DL burning is supposed to be better with 7. I didn't get it just for that though.
The CMC manufactured TTH02 media is a bit on the questionable side. I'd try something else with Made in Japan on it, to be on the safe side for test purposes. What brand is your media, we already know who manufactured it? Just curious.
By any chance is this an external drive? Let us in on your system, and some specs. It helps sometimes.
You need to get a mod to move the thread to Nero Discussion for best coverage on reading Nero logs.
Once you get everything up to par do another burn. If it's not okay and you need help, post the new log.
To Do list:
Firmware, check to see if an update is needed.
Software, update.
Media, get good media. There's a number of name options Sony, Verbatim, and Taiyo Yuden for instance. Remember MIJ. There's more good media, just the MIJ is easier to locate before purchase.
|
Moderator
|
21. April 2006 @ 02:23 |
Link to this message
|
thread teleported to Nero forum..
i've also subscribed to see if there's anything i can add; at the moment i can see Roxio is installed, which can cause problems with Nero (i believe brobear has Roxio and various other programs co-existing, however it's not brobear who's having burn problems so i'd suggest uninstalling Roxio for now and fully uninstalling it via Roxio Zapper - http://www.softpedia.com/get/Tweak/Uninstallers/Roxio-Zap.shtml
:)
Main PC ~ Intel C2Q Q6600 (G0 Stepping)/Gigabyte GA-EP45-DS3/2GB Crucial Ballistix PC2-8500/Zalman CNPS9700/Antec 900/Corsair HX 620W
Network ~ DD-WRT ~ 2node WDS-WPA2/AES ~ Buffalo WHR-G54S. 3node WPA2/AES ~ WRT54GS v6 (inc. WEP BSSID), WRT54G v2, WRT54G2 v1. *** Forum Rules *** |
|
Kevthekev
Suspended due to non-functional email address
|
21. April 2006 @ 03:05 |
Link to this message
|
|
Nice to meet you Creaky. Thanks I'll give that a try.
|
AfterDawn Addict
|
21. April 2006 @ 03:09 |
Link to this message
|
Quote:
Burn process failed at 16x (22,160 KB/s)
I would slow burn to 4X also....16X is way too fast.
|
Moderator
|
21. April 2006 @ 03:15 |
Link to this message
|
Just noticed near top of logfile that your nero does indeed need updating (I'm on handheld so can't copy/paste, but it's the couple of lines where is says something like "connected to mmc recorder" or similar - those 2 lines means Nero is too old to recognise your dvd burner correctly and its only recognised generically..
edit-
Quote:
Connected to MMC as unknown drive with class-nr : 1
Drive is autodetected - recorder class: Std. MMC recorder
- those were the 2 lines i meant..
Main PC ~ Intel C2Q Q6600 (G0 Stepping)/Gigabyte GA-EP45-DS3/2GB Crucial Ballistix PC2-8500/Zalman CNPS9700/Antec 900/Corsair HX 620W
Network ~ DD-WRT ~ 2node WDS-WPA2/AES ~ Buffalo WHR-G54S. 3node WPA2/AES ~ WRT54GS v6 (inc. WEP BSSID), WRT54G v2, WRT54G2 v1. *** Forum Rules ***
This message has been edited since posting. Last time this message was edited on 21. April 2006 @ 03:24
|
AfterDawn Addict
|
21. April 2006 @ 03:18 |
Link to this message
|
This message has been edited since posting. Last time this message was edited on 21. April 2006 @ 03:20
|
Moderator
|
21. April 2006 @ 03:25 |
Link to this message
|
|
a-ha, that's what i was after,cheers Gwen..
and i've edited my previous reply...
Main PC ~ Intel C2Q Q6600 (G0 Stepping)/Gigabyte GA-EP45-DS3/2GB Crucial Ballistix PC2-8500/Zalman CNPS9700/Antec 900/Corsair HX 620W
Network ~ DD-WRT ~ 2node WDS-WPA2/AES ~ Buffalo WHR-G54S. 3node WPA2/AES ~ WRT54GS v6 (inc. WEP BSSID), WRT54G v2, WRT54G2 v1. *** Forum Rules ***
|
AfterDawn Addict
|
21. April 2006 @ 03:47 |
Link to this message
|
Quote:
Last possible write address on media: 2298495 (510:46.45, 4489MB)
Last address to be written: 2286111 (508:01.36, 4465MB)
Just a suggestion, you may want to adjust the burn parameters a little lower as you are burning very close to the edge of the media. On lesser quality media the dye spread is not as evenly spread near the edge and burning there may cause playback issues.
Now with quality media, some burn right to the edge without issues.
|
|
brobear
Suspended permanently
|
21. April 2006 @ 12:00 |
Link to this message
|
@Kevthekev
Quote:
To Do list:
Firmware, check to see if an update is needed.
Software, update.
Media, get good media. There's a number of name options Sony, Verbatim, and Taiyo Yuden for instance. Remember MIJ. There's more good media, just the MIJ is easier to locate before purchase.
Seems we're all in agreement and Gwendolin was nice enough to supply the software update link for you. Let us know how it's going or if you're still running into trouble after the updates and better media.
This message has been edited since posting. Last time this message was edited on 21. April 2006 @ 12:06
|
|
Kevthekev
Suspended due to non-functional email address
|
22. April 2006 @ 06:08 |
Link to this message
|
Success!!!! I am now happily burning again.
Guys, Took your advice and updated Nero and changed media. I was using imation DVD+R 8x..... crap discs. Changed to Verbitan DVD+R 8X and also reinstalled Decryptor & Shrink and burned at 4x.
Thank you so much for your help. 1'm off to do some more burning.
Cheers
Kevthekev
|
|
Advertisement
|
|
|
|
brobear
Suspended permanently
|
22. April 2006 @ 11:03 |
Link to this message
|
|
You're welcome. Glad to see you got things going.
|
|
