|
|
|
"command sequence error" and "logical block address out of range"
|
|
|
reefis
Newbie
|
22. February 2007 @ 09:41 |
Link to this message
|
Hello,
for at least two years I've had no problems burning dvd's and cd's on my internal Memorex 16+/-DL4RWID2 using Nero. Just the past week I've been getting "pma update failure" when trying to burn cds. with dvd's i get "command sequence error". I did disk cleanup, defrags, updated the firmware. Somehow i can burn cd's again, if i burn at 24x. but still no luck with dvds. I downloaded Cheetah DVD burner to see if it's a problem with Nero, and I got "logical block address out of range" Basically, if you listen to the burner, it seems to be having trouble getting started in the burning process. it seems to be stalling out. you'll hear it rev up for a few seconds and then it stops. eventually it kicks in and seems to be working fine, but after 2 minutes I get the failure messages.. I've tried different media. I just bought a Memorex 50 pack (seems like it'd be very compatible with a memorex burner) and wasn't having any luck with those, so I found a blank Sony disc. IT IS NOT A MEDIA ISSUE. I've tried burning data dvd, video dvds, nothing works at any speeds.. I've wasted at least 15 dvds thus far. Everything was working fine a month ago. I havn't found any helpful info anywheres on the internet. Does anyone have any suggestions? here is my log...
bubba
Windows XP 5.1
IA32
WinAspi: File 'Wnaspi32.dll': Ver=4.71 (0002), size=45056 bytes, created 11/21/2005 12:48:21 AM
ahead WinASPI: File 'C:\Program Files\Nero\Nero 7\Core\Wnaspi32.dll': Ver=2.0.1.74, size=164112 bytes, created 11/2/2004 12:54:32 PM
NT-SPTI used
Nero Version: 7.0.0.0 (Nero Express)
Recorder: <Memorex DVD16+/-DL4RWlD2>Version: JWS6 - HA 1 TA 5 - 7.0.0.0
Adapter driver: <IDE> HA 1
Drive buffer : 2048kB
Bus Type : default (0) -> ATAPI, detected: ?
CD-ROM: <HL-DT-ST DVD-ROM GDR8163B>Version: 0D20 - HA 1 TA 0 - 7.0.0.0
Adapter driver: <IDE> HA 1
=== Scsi-Device-Map ===
DiskPeripheral : WDC WD1600JB-75GVA0 atapi Port 0 ID 0 DMA: On
CdRomPeripheral : HL-DT-ST DVD-ROM GDR8163B atapi Port 1 ID 0 DMA: Off
CdRomPeripheral : Memorex DVD16+/-DL4RWlD2 atapi Port 1 ID 1 DMA: Off
CdRomPeripheral : Generic DVD-ROM 1.0 d347prt Port 2 ID 0 DMA: Off
=== CDRom-Device-Map ===
HL-DT-ST DVD-ROM GDR8163B D: CDRom0
Generic DVD-ROM E: CDRom2
Memorex DVD16+/-DL4RWlD2 F: CDRom5
=======================
AutoRun : 1
Excluded drive IDs:
WriteBufferSize: 74448896 (0) Byte
ShowDrvBufStat : 0
BUFE : 0
Physical memory : 509MB (522224kB)
Free physical memory: 206MB (211036kB)
Memory in use : 59 %
Uncached PFiles: 0x0
Use Inquiry : 1
Global Bus Type: default (0)
Check supported media : Disabled (0)
22.2.2007
ISO compilation
11:32:46 AM #1 Text 0 File Isodoc.cpp, Line 6410
Iso document burn settings
------------------------------------------
Determine maximum speed : FALSE
Simulate : FALSE
Write : TRUE
Finalize CD : TRUE
Multisession : FALSE
Burning mode : DAO
Mode : 1
ISO Level : 1 (Max. of 11 = 8 + 3 char)
Character set : ISO 9660
Joliet : TRUE
Allow pathdepth more than 8 directories : TRUE
Allow more than 255 characters in path : TRUE
Write ISO9660 ;1 file extensions : TRUE
11:32:47 AM #2 Text 0 File ThreadedTransfer.cpp, Line 525
ReadBuffer-Pipe got 72704KB of Memory
11:32:47 AM #3 Text 0 File Reader.cpp, Line 124
Reader running
11:32:47 AM #4 Text 0 File Writer.cpp, Line 113
Writer F: Memorex DVD16+/-DL4RWlD2 running
11:32:47 AM #5 ISO9660GEN -11 File Geniso.cpp, Line 3304
First writeable address = 0 (0x00000000)
11:32:47 AM #6 Text 0 File Burncd.cpp, Line 3301
Turn on Disc-At-Once, using DVD media
11:32:47 AM #7 Text 0 File DlgWaitCD.cpp, Line 277
Last possible write address on media: 2298495 (510:46.45, 4489MB)
Last address to be written: 1976991 (439:19.66, 3861MB)
11:32:47 AM #8 Text 0 File DlgWaitCD.cpp, Line 289
Write in overburning mode: NO (enabled: CD)
11:32:47 AM #9 Text 0 File DlgWaitCD.cpp, Line 2568
Recorder: Memorex DVD16+/-DL4RWlD2, Media type: DVD-R
Disc Manufacturer: CMC MA - G. AM3
Disc Application Code: 64, Disc Physical Code: 193
11:32:47 AM #10 Text 0 File DlgWaitCD.cpp, Line 456
>>> Protocol of DlgWaitCD activities: <<<
=========================================
11:32:47 AM #11 Text 0 File ThreadedTransferInterface.cpp, Line 846
Setup items (after recorder preparation)
0: TRM_DATA_MODE1 ()
2 indices, index0 (150) not provided
original disc pos #0 + 1976992 (1976992) = #1976992/439:19.67
relocatable, disc pos for caching/writing not required/ required, no patch infos
-> TRM_DATA_MODE1, 2048, config 0, wanted index0 0 blocks, length 1976992 blocks [F: Memorex DVD16+/-DL4RWlD2]
--------------------------------------------------------------
11:32:47 AM #12 Text 0 File ThreadedTransferInterface.cpp, Line 1058
Prepare recorder [F: Memorex DVD16+/-DL4RWlD2] for write in CUE-sheet-DAO
DAO infos:
==========
MCN: ""
TOCType: 0x00; Session Closed, disc fixated
Tracks 1 to 1:
1: TRM_DATA_MODE1, 2048/0x00, FilePos 0 0 4048879616, ISRC ""
DAO layout:
===========
__Start_|____Track_|_Idx_|_CtrlAdr_|_RecDep__________
0 | lead-in | 0 | 0x41 | 0x00
0 | 1 | 0 | 0x41 | 0x00
0 | 1 | 1 | 0x41 | 0x00
1976992 | lead-out | 1 | 0x41 | 0x00
11:32:47 AM #13 Text 0 File SCSIPassThrough.cpp, Line 34
SPTILockVolume - completed successfully for FCTL_LOCK_VOLUME
11:32:47 AM #14 Phase 24 File dlgbrnst.cpp, Line 1724
Caching of files started
11:32:47 AM #15 Text 0 File Burncd.cpp, Line 4129
Cache writing successful.
11:32:47 AM #16 Phase 25 File dlgbrnst.cpp, Line 1724
Caching of files completed
11:32:47 AM #17 Phase 36 File dlgbrnst.cpp, Line 1724
Burn process started at 6x (8,310 KB/s)
11:32:47 AM #18 Text 0 File ThreadedTransferInterface.cpp, Line 2669
Verifying disc position of item 0 (relocatable, disc pos, no patch infos, orig at #0): write at #0
11:32:47 AM #19 Text 0 File DVDR.cpp, Line 2469
Recording mode: Sequential Recording Mode
11:32:47 AM #20 Text 0 File MMC.cpp, Line 21541
Set BUFE: Buffer underrun protection -> ON , Adapt writespeed to disc : ON
11:32:47 AM #21 Text 0 File DVDR.cpp, Line 2624
Start write address at LBA 0
DVD high compatibility mode: Yes
11:32:47 AM #22 Text 0 File Cdrdrv.cpp, Line 8385
---- DVD Structure: Physical Format Information (00h) ----
Layer: 0, Address: 0 (0 h), AGID: 0; Length: 2050
Book Type: DVD-R (2), Part Version: 2.0x (5), Extended Part Version: 2.1 (33)
Disc Size: 120 mm, Maximum Rate: <not specified> (F h)
Number of Layers: 1, Track Path: Parallel Track Path (PTP), Layer Type: recordable
Linear Density: 0,267 um/bit, Track Density: 0,74 um/track
Starting Physical Sector Number of Data Area: 30000 h (DVD-ROM, DVD-R/-RW, DVD+R/+RW)
End Physical Sector Number of Data Area: 0 h
End Sector Number in Layer 0: 0 h (LBN: FFFD0000 h, 4193920 MB)
Data in Burst Cutting Area (BCA) does not exist
Start sector number of the current Border-Out: 0 h
Start sector number of the next Border-In: 0 h
Media Specific [16..63]:
00 60 00 10 20 30 40 50 - 00 00 00 21 00 00 00 00 .`...0@P...!....
00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................
11:33:41 AM #23 Text 0 File Cdrdrv.cpp, Line 1195
11:33:41.031 - F: Memorex DVD16+/-DL4RWlD2 : Queue again later
11:34:45 AM #24 SPTI -600 File SCSIPassThrough.cpp, Line 306
CdRom5: SCSIStatus(x00) WinError(121) NeroError(-600)
Sense Key: 0x00 (KEY_NO_SENSE)
Sense Code: 0x00
Sense Qual: 0x00
CDB Data: 0x5C 00 00 00 00 00 00 00 0C 00 00 00
Sense Area: 0x00 00 00 00 00 00 00 00 00 00 00 00 00
Buffer x03e69400: Len xc
11:36:09 AM #25 SPTI -1114 File SCSIPassThrough.cpp, Line 306
CdRom5: SCSIStatus(x02) WinError(0) NeroError(-1114)
Sense Key: 0x06 (KEY_UNIT_ATTENTION)
Sense Code: 0x29
Sense Qual: 0x00
CDB Data: 0x5C 00 00 00 00 00 00 00 0C 00 00 00
Sense Area: 0x70 00 06 00 00 00 00 0A 00 00 00 00 29
Buffer x03e69400: Len xc
11:36:09 AM #26 SPTI -1023 File SCSIPassThrough.cpp, Line 306
CdRom5: SCSIStatus(x02) WinError(0) NeroError(-1023)
Sense Key: 0x05 (KEY_ILLEGAL_REQUEST)
Sense Code: 0x2C
Sense Qual: 0x00
CDB Data: 0x2A 00 00 00 04 A0 00 00 20 00 00 00
Sense Area: 0x70 00 05 00 00 00 00 0A 00 00 00 00 2C
Buffer x03840000: Len x10000
0x4A 92 51 49 08 06 A3 C6 B3 79 C3 73 BD 3C A7 7B
0xE0 AB 86 18 EE E2 0A EE D3 E9 5B F5 F8 63 BE ED
0x70 15 33 26 40 58 ED 13 F7 1E 86 BA 5E 75 96 79
11:36:09 AM #27 CDR -1023 File Writer.cpp, Line 302
Command sequence error
F: Memorex DVD16+/-DL4RWlD2
11:36:09 AM #28 Text 0 File ThreadedTransfer.cpp, Line 228
all writers idle, stopping conversion
11:36:10 AM #29 Text 0 File ThreadedTransfer.cpp, Line 222
conversion idle, stopping reader
11:36:10 AM #30 Text 0 File DVDR.cpp, Line 2866
EndDAO: Last written address was 1183
11:36:10 AM #31 Phase 38 File dlgbrnst.cpp, Line 1724
Burn process failed at 6x (8,310 KB/s)
Existing drivers:
File 'Drivers\ADPU160M.SYS': Ver=v3.60a (Lab01_N(johnstra).010529-2218), size=101888 bytes, created 8/17/2001 3:07:32 PM
File 'Drivers\CDRALW2K.SYS': Ver=8.0.0.212 , size=2560 bytes, created 5/19/2006 4:16:24 PM
File 'Drivers\ASPI32.SYS': Ver=4.71 (0002) built by: WinDDK, size=16512 bytes, created 11/21/2005 12:48:21 AM
File 'Drivers\PXHELP20.SYS': Ver=3.00.11B, size=46080 bytes, created 5/16/2006 3:23:54 PM (Prassi/Veritas driver for win 2K)
Registry Keys:
HKLM\Software\Microsoft\Windows NT\CurrentVersion\WinLogon\AllocateCDROMs : 0 (Security Option)
I need your guidance
This message has been edited since posting. Last time this message was edited on 22. February 2007 @ 19:15
|
|
Advertisement
|
|
|
|
Moderator
|
22. February 2007 @ 17:12 |
Link to this message
|
Hi reefis
1st thing edit out the serial # is the log. At the top and begins w/ 1C.
CdRomPeripheral : HL-DT-ST DVD-ROM GDR8163B atapi Port 1 ID 0 DMA: Off
CdRomPeripheral : Memorex DVD16+/-DL4RWlD2 atapi Port 1 ID 1 DMA: Off
Turn DMA back on for these drives. Here's a guide - link
Nero Version: 7.0.0.0
Nero can use an update - latest is 7.7.5.1 - may not be part of this problem but several fixes and enhancements since the version you have.
The Memorex you have were made by CMC - not the best but turn DMA back for the drive and see how that goes.
File 'Drivers\CDRALW2K.SYS'
Roxio & Nero don't always play well. If still failing may want to try uninstalling Roxio and run the zap tool to remove it all.
|
|
reefis
Newbie
|
22. February 2007 @ 20:48 |
Link to this message
|
|
thanks for the help. much appreciated
i changed the dma. for some reason, since my burner is a slave drive, dma cannot be turned on, or isn't available. I believe this has always been the case, it's just causes a slower burn. (correct?) it seems very odd that when the burner starts the job is stalls (starts briefly and then stops) at least 4 different times before starting up and stopping after 2 or 3 minutes.. I thought maybe it could be a problem with windows media connect taking up too much memory, so i uninstalled that and then nothing... i'm am trying to figure out if CDRALW2K.SYS' has anything to do with it.
I need your guidance
|
Moderator
|
23. February 2007 @ 14:20 |
Link to this message
|
|
How about the DVD-Rom drive - were you able to turn DMA on for that one?
Since your hard drive is in DMA - as faster data transfer rate then the slow PIO mode it could cause problems & failures. Slowness being one of them.
Manually change transfer mode in the drop down to 'dma if available' for each one in the seconardy channel then uninstall the ide channel again and reboot.
You mighthave a bad ide cable & that might be the reason for staying in PIO and possibly the burn failures.
For the Roxio if you've had in installed all this time then it may not be the problem.
Might want to rule it out anyhow but need to get the drive back in DMA mode too.
Oh and you're welcome!
|
|
reefis
Newbie
|
23. February 2007 @ 17:09 |
Link to this message
|
|
yes, i WAS able to turn DMA on for my dvd-rom drive. I'll open up my computer tommorow and see what's up, I might as well make my burner my master anyway. Do wires ever unattach or burnout?
I need your guidance
|
Moderator
|
23. February 2007 @ 18:04 |
Link to this message
|
|
They can - unfortunately nothing lasts forever :)
But switch it to master & see how that goes- change the jumper pins on the back of the drives too - dvd-rom will now be set to slave & burner to master.
Keep us posted!
|
|
reefis
Newbie
|
28. February 2007 @ 07:32 |
Link to this message
|
hello, i did the latter, and turned dma on. I think it IS A MEDIA issue because I got a successful burn with a Sony DVD-R at 6x. with the crappy memorex branded DVD-R it failed again. (this time i had a "reset error" ?). here's the log for that specific burn if you can find anything else fishy. I noticed that my buffer size is only 2 mb. that doesn't seem right to me. is it?
Windows XP 5.1
IA32
WinAspi: File 'Wnaspi32.dll': Ver=4.71 (0002), size=45056 bytes, created 7/17/2002 9:20:56 AM
ahead WinASPI: File 'C:\Program Files\Nero\Nero 7\Core\Wnaspi32.dll': Ver=2.0.1.74, size=164112 bytes, created 11/2/2004 12:54:32 PM
NT-SPTI used
Nero Version: 7.0.0.0 (Nero Express)
Recorder: <Memorex DVD16+/-DL4RWlD2>Version: JWS6 - HA 1 TA 3 - 7.0.0.0
Adapter driver: <IDE> HA 1
Drive buffer : 2048kB
Bus Type : default (0) -> ATAPI, detected: ?
CD-ROM: <Generic DVD-ROM >Version: 1.0 - HA 1 TA 1 - 7.0.0.0
Adapter driver: <SCSI> HA 1
=== Scsi-Device-Map ===
DiskPeripheral : WDC WD1600JB-75GVA0 atapi Port 0 ID 0 DMA: On
CdRomPeripheral : Memorex DVD16+/-DL4RWlD2 atapi Port 1 ID 0 DMA: On
CdRomPeripheral : Generic DVD-ROM 1.0 d347prt Port 2 ID 0 DMA: Off
=== CDRom-Device-Map ===
Memorex DVD16+/-DL4RWlD2 D: CDRom3
Generic DVD-ROM E: CDRom1
=======================
AutoRun : 1
Excluded drive IDs:
WriteBufferSize: 83886080 (83886080) Byte
ShowDrvBufStat : 0
BUFE : 0
Physical memory : 509MB (522224kB)
Free physical memory: 153MB (157108kB)
Memory in use : 69 %
Uncached PFiles: 0x0
Use Inquiry : 1
Global Bus Type: default (0)
Check supported media : Disabled (0)
28.2.2007
ISO compilation
10:38:02 AM #1 Text 0 File Isodoc.cpp, Line 6410
Iso document burn settings
------------------------------------------
Determine maximum speed : FALSE
Simulate : FALSE
Write : TRUE
Finalize CD : TRUE
Multisession : FALSE
Burning mode : DAO
Mode : 1
ISO Level : 1 (Max. of 11 = 8 + 3 char)
Character set : ISO 9660
Joliet : TRUE
Allow pathdepth more than 8 directories : TRUE
Allow more than 255 characters in path : TRUE
Write ISO9660 ;1 file extensions : TRUE
10:38:02 AM #2 Text 0 File ThreadedTransfer.cpp, Line 525
ReadBuffer-Pipe got 81920KB of Memory
10:38:02 AM #3 Text 0 File Reader.cpp, Line 124
Reader running
10:38:02 AM #4 Text 0 File Writer.cpp, Line 113
Writer D: Memorex DVD16+/-DL4RWlD2 running
10:38:02 AM #5 ISO9660GEN -11 File Geniso.cpp, Line 3304
First writeable address = 0 (0x00000000)
10:38:02 AM #6 Text 0 File Burncd.cpp, Line 3301
Turn on Disc-At-Once, using DVD media
10:38:02 AM #7 Text 0 File DlgWaitCD.cpp, Line 277
Last possible write address on media: 2298495 (510:46.45, 4489MB)
Last address to be written: 2235903 (496:52.03, 4366MB)
10:38:02 AM #8 Text 0 File DlgWaitCD.cpp, Line 289
Write in overburning mode: NO
10:38:02 AM #9 Text 0 File DlgWaitCD.cpp, Line 2568
Recorder: Memorex DVD16+/-DL4RWlD2, Media type: DVD-R
Disc Manufacturer: CMC MA - G. AM3
Disc Application Code: 64, Disc Physical Code: 193
10:38:02 AM #10 Text 0 File DlgWaitCD.cpp, Line 456
>>> Protocol of DlgWaitCD activities: <<<
=========================================
10:38:02 AM #11 Text 0 File ThreadedTransferInterface.cpp, Line 846
Setup items (after recorder preparation)
0: TRM_DATA_MODE1 ()
2 indices, index0 (150) not provided
original disc pos #0 + 2235904 (2235904) = #2235904/496:52.4
relocatable, disc pos for caching/writing not required/ required, no patch infos
-> TRM_DATA_MODE1, 2048, config 0, wanted index0 0 blocks, length 2235904 blocks [D: Memorex DVD16+/-DL4RWlD2]
--------------------------------------------------------------
10:38:02 AM #12 Text 0 File ThreadedTransferInterface.cpp, Line 1058
Prepare recorder [D: Memorex DVD16+/-DL4RWlD2] for write in CUE-sheet-DAO
DAO infos:
==========
MCN: ""
TOCType: 0x00; Session Closed, disc fixated
Tracks 1 to 1:
1: TRM_DATA_MODE1, 2048/0x00, FilePos 0 0 4579131392, ISRC ""
DAO layout:
===========
__Start_|____Track_|_Idx_|_CtrlAdr_|_RecDep__________
0 | lead-in | 0 | 0x41 | 0x00
0 | 1 | 0 | 0x41 | 0x00
0 | 1 | 1 | 0x41 | 0x00
2235904 | lead-out | 1 | 0x41 | 0x00
10:38:02 AM #13 Text 0 File SCSIPassThrough.cpp, Line 34
SPTILockVolume - completed successfully for FCTL_LOCK_VOLUME
10:38:03 AM #14 Phase 24 File dlgbrnst.cpp, Line 1724
Caching of files started
10:38:03 AM #15 Text 0 File Burncd.cpp, Line 4129
Cache writing successful.
10:38:03 AM #16 Phase 25 File dlgbrnst.cpp, Line 1724
Caching of files completed
10:38:03 AM #17 Phase 36 File dlgbrnst.cpp, Line 1724
Burn process started at 6x (8,310 KB/s)
10:38:03 AM #18 Text 0 File ThreadedTransferInterface.cpp, Line 2669
Verifying disc position of item 0 (relocatable, disc pos, no patch infos, orig at #0): write at #0
10:38:03 AM #19 Text 0 File DVDR.cpp, Line 2469
Recording mode: Sequential Recording Mode
10:38:03 AM #20 Text 0 File MMC.cpp, Line 21541
Set BUFE: Buffer underrun protection -> ON , Adapt writespeed to disc : ON
10:38:03 AM #21 Text 0 File DVDR.cpp, Line 2624
Start write address at LBA 0
DVD high compatibility mode: Yes
10:38:03 AM #22 Text 0 File Cdrdrv.cpp, Line 8385
---- DVD Structure: Physical Format Information (00h) ----
Layer: 0, Address: 0 (0 h), AGID: 0; Length: 2050
Book Type: DVD-R (2), Part Version: 2.0x (5), Extended Part Version: 2.1 (33)
Disc Size: 120 mm, Maximum Rate: <not specified> (F h)
Number of Layers: 1, Track Path: Parallel Track Path (PTP), Layer Type: recordable
Linear Density: 0,267 um/bit, Track Density: 0,74 um/track
Starting Physical Sector Number of Data Area: 30000 h (DVD-ROM, DVD-R/-RW, DVD+R/+RW)
End Physical Sector Number of Data Area: 0 h
End Sector Number in Layer 0: 0 h (LBN: FFFD0000 h, 4193920 MB)
Data in Burst Cutting Area (BCA) does not exist
Start sector number of the current Border-Out: 0 h
Start sector number of the next Border-In: 0 h
Media Specific [16..63]:
00 60 00 10 20 30 40 50 - 00 00 00 21 00 00 00 00 .`...0@P...!....
00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................
10:39:08 AM #23 Text 0 File Cdrdrv.cpp, Line 1195
10:39:08.234 - D: Memorex DVD16+/-DL4RWlD2 : Queue again later
10:42:41 AM #24 SPTI -1114 File SCSIPassThrough.cpp, Line 306
CdRom3: SCSIStatus(x02) WinError(0) NeroError(-1114)
Sense Key: 0x06 (KEY_UNIT_ATTENTION)
Sense Code: 0x29
Sense Qual: 0x00
CDB Data: 0x2A 00 00 06 AB 00 00 00 20 00 00 00
Sense Area: 0x70 00 06 00 00 00 00 0A 00 00 00 00 29
Buffer x04010000: Len x10000
0xEA A6 8F 94 22 7A 2E 83 BC 1C 91 9A 32 8D 8D E8
0xE9 FB D5 7A 59 E6 43 77 9A A0 EE 91 B0 9E C6 C3
0x54 B6 C7 6C D0 A0 33 55 32 74 64 12 30 9A AC D1
10:42:41 AM #25 CDR -1114 File Writer.cpp, Line 302
Reset occurred
D: Memorex DVD16+/-DL4RWlD2
10:42:41 AM #26 Text 0 File ThreadedTransfer.cpp, Line 228
all writers idle, stopping conversion
10:42:41 AM #27 Text 0 File ThreadedTransfer.cpp, Line 222
conversion idle, stopping reader
10:42:41 AM #28 Text 0 File DVDR.cpp, Line 2866
EndDAO: Last written address was 436991
10:42:41 AM #29 Phase 38 File dlgbrnst.cpp, Line 1724
Burn process failed at 6x (8,310 KB/s)
Existing drivers:
File 'Drivers\ADPU160M.SYS': Ver=v3.60a (Lab01_N(johnstra).010529-2218), size=101888 bytes, created 8/17/2001 3:07:32 PM
File 'Drivers\ASPI32.SYS': Ver=4.71 (0002), size=16877 bytes, created 7/17/2002 8:53:02 AM
File 'Drivers\PXHELP20.SYS': Ver=3.00.11B, size=46080 bytes, created 5/16/2006 3:23:54 PM (Prassi/Veritas driver for win 2K)
File 'Drivers\SCSIPORT.SYS': Ver=5.1.2600.2180 (xpsp_sp2_rtm.040803-2158), size=96256 bytes, created 8/4/2004 6:00:00 AM (Adapter driver for src)
Registry Keys:
HKLM\Software\Microsoft\Windows NT\CurrentVersion\WinLogon\AllocateCDROMs : 0 (Security Option)
I need your guidance
|
Moderator
|
28. February 2007 @ 15:40 |
Link to this message
|
Yeah it could definitely be a media issue - the memorex you have are made by CMC - not very good.
Plus the firmware for this drive hasn't been updated since mid 2005 so some 16x media will more than likely give it problems (like these).
The drive is actually a oem LiteOn SOHW-1673S so you could also try crossflashing the drive to the LiteOn firmware. You would need to use the patched on for the LiteOn SOHW 1693S - KSOB. Here's a link if interested - link
The 2mb buffer on the drive is pretty standard - you're good there.
|
|
reefis
Newbie
|
28. February 2007 @ 18:16 |
Link to this message
|
DUDE!! you kick ass. you solved my problems 100%! It used to take an hour to burn a dvd and now it's 7 minutes. I was able to burn the CMC DVD-R at 16x. no problems at all. Nero infotool even says i can read AND write bd-r. that can't be true, can it? wow. thank you so much!
I need your guidance
|
Moderator
|
28. February 2007 @ 19:12 |
Link to this message
|
|
lol - not a problem reefis :)
I take it you cross flashed to the LiteOn and that did the trick.
Though it won't have given the drive the ability to read & write to BluRay (check box will be to the right of BD-R). The LiteOn doesn't support it.
I'd take the CMC back down to 8x too - don't need any more coasters :)
And these can be iffy enuf as it is.
Happy Burning!
|
|
reefis
Newbie
|
1. March 2007 @ 06:00 |
Link to this message
|
|
yeah i was definately not looking at the check boxes correctly! you are very wise and i bow down to you!
I need your guidance
|
Moderator
|
1. March 2007 @ 14:50 |
Link to this message
|
|
LOL
That check box has fooled many of us :)
|
Junior Member
|
3. March 2007 @ 15:48 |
Link to this message
|
|
What a beautiful ending :)
|
Junior Member
|
3. March 2007 @ 15:48 |
Link to this message
|
|
What a beautiful ending :)
|
Junior Member
|
3. March 2007 @ 15:50 |
Link to this message
|
Originally posted by mark8766:
What a beautiful ending :)
sorry didnt mean to double
|
|
Advertisement
|
|
|
Moderator
|
3. March 2007 @ 16:05 |
Link to this message
|
|
lol - it happens to the best of us :) (double post)
|
|
