|
|
|
Shrink,Nero,Burner problem
|
|
|
talone
Newbie
|
28. March 2007 @ 14:11 |
Link to this message
|
I have searched thru your site [and some other Forums] but haven?t seen anything specific to all my problems.
I?ve been able to burn DVDs for years with same set up until now.
I hope I?ve provided all relevant info.
Various Problems I encountered with Nero:
- Illegal Disc
- Could not perform Start of Disc-at-once
- Burn process failed at 2x-
- Recorder State: Failed
Various Problems encountered with Decrypter:
- I/O error
- Cannot write medium - Incompatible Format
- Failed to Reserve Track
AND then all of a sudden, all of the time now:
- when I insert a blank -R or a just erased -RW disc, I get
- Green lite then changes to orange and goes back to green.
- Insert any blank disc and open Nero [or not] or Decrypter to burn.
- Goes back to orange but stays there indefinitely
- Also there?s an faint audible cliking sound about every 2 seconds from the burner.
- My computer then becomes squirrely, basically non-responsive, until I remove the disc.
[Because orange lit burner is draining resources?]
My Computer:
- I have Windows XP SP2 Home .
- Until a few days ago I was able to burn with Shrink and Nero, sometimes also with Decrypter.
- Because of my TV DVD player, I am restricted to DVD-Rs and DVD-RWs. But I have not found a brand of DVD-Rs lately that work . [Tried: -R: TDK, Maxell, Memorex, HP, Sony, Fujifilm, & some others.]
- But in the past I had always been successful using -RWs.
- I have uninstalled & re-installed Nec RW ND-2500A USB Device with v6.
- I have re-started computer after each change.
- I have not recently installed any other programs or security programs.
- Because of, and during the problems I was experiencing noted above, I upgraded to use Nero7. I was successful burning several DVD-RWs until couple days ago. [But 7?s not Free so I will be going back to 6 after current problems are resolved.]
- Below are 2 logs, 1 Nero log and 1 Decrypter log.
- I was using the same blank Fujifilm DVD-RW made by RITEK WO1, at Speed 2X.
Nero log 3/27
Windows XP 5.1
IA32
WinAspi: -
NT-SPTI used
Nero Version: 7.8.5.0
Internal Version: 7, 8, 5, 0
Recorder: <_NEC DVD_RW ND-2500A> Version: 1.06 - HA 1 TA 3 - 7.8.5.0
Adapter driver: <USB 2.0> HA 1
Drive buffer : 2048kB
Bus Type : set to ATAPI (3) -> ATAPI, detected: ?
CD-ROM: <TOSHIBA DVD-ROM SD-M1612>Version: 1808 - HA 1 TA 0 - 7.8.5.0
Adapter driver: <IDE> HA 1
=== Scsi-Device-Map ===
DiskPeripheral : ST3120025A atapi Port 0 ID 0 DMA: On
CdRomPeripheral : TOSHIBA DVD-ROM SD-M1612 atapi Port 1 ID 0 DMA: On
CdRomPeripheral : LITE-ON LTR-48246S atapi Port 1 ID 1 DMA: On
=== CDRom-Device-Map ===
TOSHIBA DVD-ROM SD-M1612 E: CDRom0
LITE-ON LTR-48246S F: CDRom1
_NEC DVD_RW ND-2500A G: CDRom3
=======================
AutoRun : 1
Excluded drive IDs:
WriteBufferSize: 73400320 (0) Byte
BUFE : 0
Physical memory : 503MB (515604kB)
Free physical memory: 133MB (136536kB)
Memory in use : 73 %
Uncached PFiles: 0x0
Use Inquiry : 1
Global Bus Type: default (0)
Check supported media : Disabled (0)
27.3.2007
Burn DVD Image
11:47:35 PM #1 Text 0 File SCSIPTICommands.cpp, Line 411
LockMCN - completed sucessfully for IOCTL_STORAGE_MCN_CONTROL
11:47:35 PM #2 Text 0 File Burncd.cpp, Line 3499
Turn on Disc-At-Once, using DVD media
11:47:35 PM #3 Text 0 File DlgWaitCD.cpp, Line 307
Last possible write address on media: 2298495 (510:46.45, 4489MB)
Last address to be written: 2285849 (507:57.74, 4464MB)
11:47:35 PM #4 Text 0 File DlgWaitCD.cpp, Line 319
Write in overburning mode: NO (enabled: CD)
11:47:35 PM #5 Text 0 File DlgWaitCD.cpp, Line 2949
Recorder: _NEC DVD_RW ND-2500A, Media type: DVD-RW
Disc Manufacturer: RITEKW - 01
Disc Application Code: 64, Disc Physical Code: 214
11:47:35 PM #6 Text 0 File DlgWaitCD.cpp, Line 493
>>> Protocol of DlgWaitCD activities: <<<
=========================================
11:47:35 PM #7 Text 0 File ThreadedTransferInterface.cpp, Line 793
Setup items (after recorder preparation)
0: TRM_DATA_MODE1 (2 - CD-ROM Mode 1, ISO 9660)
2 indices, index0 (150) not provided
original disc pos #0 + 2285850 (2285850) = #2285850/507:58.0
not relocatable, disc pos for caching/writing not required/not required
-> TRM_DATA_MODE1, 2048, config 0, wanted index0 0 blocks, length 2285850 blocks [G: _NEC DVD_RW ND-2500A]
--------------------------------------------------------------
11:47:35 PM #8 Text 0 File ThreadedTransferInterface.cpp, Line 995
Prepare [G: _NEC DVD_RW ND-2500A] for write in CUE-sheet-DAO
DAO infos:
==========
MCN: ""
TOCType: 0x00; Session Closed, disc fixated
Tracks 1 to 1: Idx 0 Idx 1 Next Trk
1: TRM_DATA_MODE1, 2048/0x00, FilePos 0 0 4681420800, ISRC ""
DAO layout:
===========
___Start_|____Track_|_Idx_|_CtrlAdr_|_____Size_|______NWA_|_RecDep__________
0 | lead-in | 0 | 0x41 | 0 | 0 | 0x00
0 | 1 | 0 | 0x41 | 0 | 0 | 0x00
0 | 1 | 1 | 0x41 | 2285850 | 2285850 | 0x00
2285850 | lead-out | 1 | 0x41 | 0 | 0 | 0x00
11:47:35 PM #9 Text 0 File SCSIPTICommands.cpp, Line 209
SPTILockVolume - completed successfully for FCTL_LOCK_VOLUME
11:47:35 PM #10 Text 0 File Burncd.cpp, Line 4278
Caching options: cache CDRom or Network-No, small files-No (<64KB)
11:47:35 PM #11 Phase 36 File dlgbrnst.cpp, Line 1762
Burn process started at 2x (2,770 KB/s)
11:47:35 PM #12 Text 0 File ThreadedTransferInterface.cpp, Line 2721
Verifying disc position of item 0 (not relocatable, no disc pos, no patch infos, orig at #0): write at #0
11:47:35 PM #13 Text 0 File DVDR.cpp, Line 3192
Recording mode: Sequential Recording Mode
11:47:35 PM #14 Text 0 File DVDR.cpp, Line 3348
Start write address at LBA 0
DVD high compatibility mode: Yes
11:47:36 PM #15 Text 0 File Cdrdrv.cpp, Line 9859
---- Disc Structure: Physical Format Information (00h) ----
Media Type: 0, Layer: 0, Address: 0 (0 h), AGID: 0; Length: 2050
Book Type: DVD-RW (3), Part Version: 1.1x (2)
Disc Size: 120 mm, Maximum Rate: <not specified> (F h)
Number of Layers: 1, Track Path: Parallel Track Path (PTP), Layer Type: recordable
Linear Density: 0,267 um/bit, Track Density: 0,74 um/track
Starting Physical Sector Number of Data Area: 30000 h (DVD-ROM, DVD-R/-RW, DVD+R/+RW)
End Sector Number in Layer 0: 0 h (LBN: FFFD0000 h, 4193920 MB)
Data in Burst Cutting Area (BCA) exist
Revision number of maximum recording speed: -
Revision number of minimum recording speed: -
Revision number table of recording speed: - - - - - - -
Class: 0
Start sector number of the current Border-Out: 2FE10 h
Start sector number of the next Border-In: 2FFA0 h
Media Specific [16..63]:
80 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................
00 02 FE 10 00 02 FF A0 - 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................
11:47:36 PM #16 Text 0 File ThreadedTransfer.cpp, Line 269
Pipe memory size 73340800
11:47:37 PM #17 Text 0 File Cdrdrv.cpp, Line 1338
23:47:37.062 - G: _NEC DVD_RW ND-2500A : Queue again later
11:47:37 PM #18 SPTI -600 File SCSIPassThrough.cpp, Line 179
CdRom3: SCSIStatus(x00) WinError(121) NeroError(-600)
Sense Key: 0x00 (KEY_NO_SENSE)
Sense Code: 0x00
Sense Qual: 0x00
CDB Data: 0x2A 00 00 00 00 00 00 00 20 00 00 00
Sense Area: 0x00 00 00 00 00 00 00 00 00 00 00 00 00
Buffer x07180040: Len x10000
0x00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
11:47:37 PM #19 CDR -600 File Writer.cpp, Line 303
Device not available
G: _NEC DVD_RW ND-2500A
11:47:58 PM #20 Text 0 File DVDR.cpp, Line 3750
EndDAO: Last written address was -1 (FFFFFFFFh)
11:47:58 PM #21 CDR -1114 File WriterStatus.cpp, Line 162
Reset occurred
G: _NEC DVD_RW ND-2500A
11:47:58 PM #22 TRANSFER -24 File WriterStatus.cpp, Line 162
Could not perform end of Disc-at-once
11:47:59 PM #23 Phase 38 File dlgbrnst.cpp, Line 1762
Burn process failed at 2x (2,770 KB/s)
11:48:00 PM #24 Text 0 File SCSIPTICommands.cpp, Line 254
SPTIDismountVolume - completed successfully for FSCTL_DISMOUNT_VOLUME
11:48:03 PM #25 Text 0 File Cdrdrv.cpp, Line 11214
DriveLocker: UnLockVolume completed
11:48:03 PM #26 Text 0 File SCSIPTICommands.cpp, Line 411
UnLockMCN - completed sucessfully for IOCTL_STORAGE_MCN_CONTROL
Existing drivers:
Registry Keys:
HKLM\Software\Microsoft\Windows NT\CurrentVersion\WinLogon\AllocateCDROMs : 0 (Security Option)
------------------------------------------------------------------------------------------------------------------------------------
Decrypter 3/27 log:
I 00:11:52 DVD Decrypter Version 3.5.4.0 started!
I 00:11:52 Microsoft Windows XP Home Edition (5.1, Build 2600 : Service Pack 2)
W 00:11:52 Drive D:\ (FAT32) does not support single files > 4 GB
I 00:11:52 Initialising SPTI...
I 00:11:52 Searching for SCSI / ATAPI devices...
I 00:11:52 Found 1 CD-RW, 1 DVD-ROM and 1 DVD±RW!
I 00:14:43 Operation Started!
I 00:14:43 Source File: C:\video.ISO
I 00:14:43 Source File Sectors: 2,285,850 (MODE1/2048)
I 00:14:43 Source File Size: 4,681,420,800 bytes
I 00:14:43 Source File Implementation Identifier: DVD Shrink
I 00:14:43 Destination Device: [0:0:0] _NEC DVD_RW ND-2500A 1.06 (G:) (USB)
I 00:14:43 Destination Media Type: DVD-RW (Disc ID: RITEKW01) (Speeds: 1x, 2x)
I 00:14:43 Destination Media Sectors: 2,298,496
I 00:14:43 Write Mode: DVD
I 00:14:43 Write Type: SAO
I 00:14:43 Write Speed: 2x
I 00:14:43 Link Size: Auto
I 00:14:43 Test Mode: No
I 00:14:43 BURN-Proof: Enabled
I 00:14:43 Filling Buffer...
I 00:14:44 Writing LeadIn...
W 00:14:45 Failed to Write Sectors 0 - 31 - The semaphore timeout period has expired.
W 00:14:45 Retrying (1 of 20)...
W 00:14:47 Retry Failed - The semaphore timeout period has expired.
W 00:14:47 Retrying (2 of 20)...
W 00:14:47 Retry Failed - Power On, Reset, or Bus Device Reset Occurred
W 00:14:47 Retrying (3 of 20)...
W 00:14:50 Retry Failed - The semaphore timeout period has expired.
W 00:14:50 Retrying (4 of 20)...
W 00:14:50 Retry Failed - Power On, Reset, or Bus Device Reset Occurred
W 00:14:50 Retrying (5 of 20)...
W 00:14:54 Retry Failed - The semaphore timeout period has expired.
W 00:14:54 Retrying (6 of 20)...
I stopped, exited program.
|
|
Advertisement
|
 |
|
|
Senior Member
|
28. March 2007 @ 16:23 |
Link to this message
|
Recorder: <_NEC DVD_RW ND-2500A> Version: 1.06
There is a firmware update for ur burner here, newest one looks like 1.0B
this should help with the write speeds for ur burner
Memory in use : 73 %
Dont multi-task when burning
Disc Manufacturer: RITEKW - 01
good disks but not the best, what is the top rated speed of the media u have been using?
i see u havent tried verbatims, first update the firmware and see if that helps with the current media u r using, if not try verbatims, or Taiyo Yudens
edit
Also ImgBurn(made by same person) is a better burning program than DVD Decrypter cuz its updated.
"When I look at the smiles on all the childrens faces, I just know theyre about to jab me with something."- Homer Simpson This message has been edited since posting. Last time this message was edited on 28. March 2007 @ 16:25
|
AfterDawn Addict
|
28. March 2007 @ 17:04 |
Link to this message
|
|
Senior Member
|
28. March 2007 @ 17:44 |
Link to this message
|
@Gwendolin,
thanks for that, i forgot to put the link in for the update.
"When I look at the smiles on all the childrens faces, I just know theyre about to jab me with something."- Homer Simpson
This message has been edited since posting. Last time this message was edited on 28. March 2007 @ 17:45
|
|
talone
Newbie
|
29. March 2007 @ 08:03 |
Link to this message
|
Thanks for info/recommendations.
- I haven?t had time to go out for Verbatim
- I uninstalled Nero 7
- I used their general cleaning tool
- I re-installed Nero 6
- I re-started computer as directed
- 1st attempt to burn with -R Memorex failed
- 2nd attempt with -R TDK resulted in return of constant orange lite and rhythmic clicking as before.
- 3rd attempt with -RW Fujifilm failed - noted ?Recorder State: Failed?
- 4th attempt with -RW Maxell resulted in ogange lite and cliking.
Log below.
I went to firmware site and unzipped.
- I don?t understand why I should change current firmware if current version had worked. I dont get the connection between orange lite/clicking and new firmware. Especially as I?ve seen comments and warnings about changing. ?
Do I need a new burner?
- If still think I should, then I?m confused with their ?Read Me.?
- Top half directions are:
Pls note following instructions for update procedure:
Connect drive to secondary IDE channel as Master
Disconnect all slave hardware from IDE secondary Master
Use standard UDMA-2 IDE cable
etc
Why do that when already unzipped?
- Bottom half directions are:
INSTALLATION: After unzipping file pls. double click on "K250GNB1.exe" file,
follow instructions. After, you have to reboot your system.
Plus
1 Deinstall all your burnsoftware(s),
2 I?ll try to get that
3 Reinstall and update your burn software. - I don?t think I have any software for it.
And, would verbatim be recognized by new firmware?
Windows XP 5.1
IA32
WinAspi: File 'Wnaspi32.dll': Ver=4.60 (1021), size=45056 bytes, created 9/10/1999 11:06:00 AM
ahead WinASPI: File 'C:\Program Files\Ahead\nero\Wnaspi32.dll': Ver=2.0.1.74, size=164112 bytes, created 11/2/2004 12:54:32 PM
NT-SPTI used
Nero Version: 6.6.1.15
Internal Version: 6, 6, 1, 15
(Nero Express)
Recorder: <_NEC DVD_RW ND-2500A> Version: 1.06 - HA 1 TA 2 - 6.6.1.15
Adapter driver: <USB 2.0> HA 1
Drive buffer : 2048kB
Bus Type : set to ATAPI (3) -> ATAPI, detected: ?
CD-ROM: <TOSHIBA DVD-ROM SD-M1612>Version: 1808 - HA 1 TA 0 - 6.6.1.15
Adapter driver: <IDE> HA 1
=== Scsi-Device-Map ===
DiskPeripheral : ST3120025A atapi Port 0 ID 0 DMA: On
CdRomPeripheral : TOSHIBA DVD-ROM SD-M1612 atapi Port 1 ID 0 DMA: On
CdRomPeripheral : LITE-ON LTR-48246S atapi Port 1 ID 1 DMA: On
=== CDRom-Device-Map ===
TOSHIBA DVD-ROM SD-M1612 E: CDRom0
LITE-ON LTR-48246S F: CDRom1
_NEC DVD_RW ND-2500A G: CDRom2
=======================
AutoRun : 1
Excluded drive IDs:
WriteBufferSize: 73400320 (0) Byte
ShowDrvBufStat : 0
BUFE : 0
Physical memory : 503MB (515604kB)
Free physical memory: 186MB (191260kB)
Memory in use : 62 %
Uncached PFiles: 0x0
Use Inquiry : 1
Global Bus Type: default (0)
Check supported media : Disabled (0)
28.3.2007
Burn DVD Image
11:14:00 PM #1 Text 0 File SCSIPTICommands.cpp, Line 403
LockMCN - completed sucessfully for IOCTL_STORAGE_MCN_CONTROL
11:14:01 PM #2 Text 0 File Burncd.cpp, Line 3316
Turn on Disc-At-Once, using DVD media
11:14:01 PM #3 Text 0 File DlgWaitCD.cpp, Line 281
Last possible write address on media: 2298495 (510:46.45, 4489MB)
Last address to be written: 2285999 (507:59.74, 4464MB)
11:14:01 PM #4 Text 0 File DlgWaitCD.cpp, Line 293
Write in overburning mode: NO (enabled: CD)
11:14:01 PM #5 Text 0 File DlgWaitCD.cpp, Line 2616
Recorder: _NEC DVD_RW ND-2500A, Media type: DVD-R
Disc Manufacturer: CMC MA - G. AM3
Disc Application Code: 64, Disc Physical Code: 193
11:14:01 PM #6 Text 0 File DlgWaitCD.cpp, Line 459
>>> Protocol of DlgWaitCD activities: <<<
=========================================
11:14:01 PM #7 Text 0 File ThreadedTransferInterface.cpp, Line 814
Setup items (after recorder preparation)
0: TRM_DATA_MODE1 (2 - CD-ROM Mode 1, ISO 9660)
2 indices, index0 (150) not provided
original disc pos #0 + 2286000 (2286000) = #2286000/508:0.0
not relocatable, disc pos for caching/writing not required/not required
-> TRM_DATA_MODE1, 2048, config 0, wanted index0 0 blocks, length 2286000 blocks [_NEC DVD_RW ND-2500A ]
--------------------------------------------------------------
11:14:01 PM #8 Text 0 File ThreadedTransferInterface.cpp, Line 1013
Prepare recorder [_NEC DVD_RW ND-2500A] for write in CUE-sheet-DAO
DAO infos:
==========
MCN: ""
TOCType: 0x00; Session Closed, disc fixated
Tracks 1 to 1:
1: TRM_DATA_MODE1, 2048/0x00, FilePos 0 0 4681728000, ISRC ""
DAO layout:
===========
__Start_|____Track_|_Idx_|_CtrlAdr_|_RecDep__________
0 | lead-in | 0 | 0x41 | 0x00
0 | 1 | 0 | 0x41 | 0x00
0 | 1 | 1 | 0x41 | 0x00
2286000 | lead-out | 1 | 0x41 | 0x00
11:14:01 PM #9 Text 0 File SCSIPTICommands.cpp, Line 208
SPTILockVolume - completed successfully for FCTL_LOCK_VOLUME
11:14:01 PM #10 Phase 24 File dlgbrnst.cpp, Line 1685
Caching of files started
11:14:01 PM #11 Text 0 File Burncd.cpp, Line 4158
Cache writing successful.
11:14:01 PM #12 Phase 25 File dlgbrnst.cpp, Line 1685
Caching of files completed
11:14:01 PM #13 Phase 36 File dlgbrnst.cpp, Line 1685
Burn process started at 2x (2,770 KB/s)
11:14:01 PM #14 Text 0 File ThreadedTransferInterface.cpp, Line 2717
Verifying disc position of item 0 (not relocatable, no disc pos, no patch infos, orig at #0): write at #0
11:14:02 PM #15 Text 0 File DVDR.cpp, Line 2846
Recording mode: Sequential Recording Mode
11:14:02 PM #16 Text 0 File DVDR.cpp, Line 3002
Start write address at LBA 0
DVD high compatibility mode: Yes
11:14:02 PM #17 Text 0 File Cdrdrv.cpp, Line 8737
---- DVD Structure: Physical Format Information (00h) ----
Media Type: 0, Layer: 0, Address: 0 (0 h), AGID: 0; Length: 2050
Book Type: DVD-R (2), Part Version: 2.0x (5), Extended Part Version: 2.1 (33)
Disc Size: 120 mm, Maximum Rate: <not specified> (F h)
Number of Layers: 1, Track Path: Parallel Track Path (PTP), Layer Type: recordable
Linear Density: 0,267 um/bit, Track Density: 0,74 um/track
Starting Physical Sector Number of Data Area: 30000 h (DVD-ROM, DVD-R/-RW, DVD+R/+RW)
End Physical Sector Number of Data Area: 26127F h
End Sector Number in Layer 0: 0 h (LBN: FFFD0000 h, 4193920 MB)
Data in Burst Cutting Area (BCA) does not exist
Start sector number of the current Border-Out: 2FE10 h
Start sector number of the next Border-In: 2FFA0 h
Media Specific [16..63]:
00 60 00 10 20 30 40 50 - 00 00 00 21 00 00 00 00 .`...0@P...!....
00 02 FE 10 00 02 FF A0 - 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................
11:14:02 PM #18 SPTI -1046 File SCSIPassThrough.cpp, Line 178
CdRom2: SCSIStatus(x02) WinError(0) NeroError(-1046)
Sense Key: 0x05 (KEY_ILLEGAL_REQUEST)
Sense Code: 0x30
Sense Qual: 0x05
CDB Data: 0x53 00 00 00 00 00 22 E1 B0 00 00 00
Sense Area: 0x70 00 05 00 00 00 00 0A 00 00 00 00 30 05
11:14:02 PM #19 CDR -1046 File ThreadedTransferInterface.cpp, Line 1767
Illegal disc
G: _NEC DVD_RW ND-2500A
11:14:02 PM #20 TRANSFER -27 File ThreadedTransferInterface.cpp, Line 1767
Could not perform start of Disc-at-once
11:14:02 PM #21 Phase 38 File dlgbrnst.cpp, Line 1685
Burn process failed at 2x (2,770 KB/s)
11:14:02 PM #22 Text 0 File SCSIPTICommands.cpp, Line 253
SPTIDismountVolume - completed successfully for FSCTL_DISMOUNT_VOLUME
11:14:04 PM #23 Text 0 File Cdrdrv.cpp, Line 9945
DriveLocker: UnLockVolume completed
11:14:04 PM #24 Text 0 File SCSIPTICommands.cpp, Line 403
UnLockMCN - completed sucessfully for IOCTL_STORAGE_MCN_CONTROL
Existing drivers:
File 'Drivers\ASPI32.SYS': Ver=4.60 (1021), size=25244 bytes, created 9/10/1999 11:06:00 AM
File 'Drivers\PXHELP20.SYS': Ver=2.02.62a, size=20016 bytes, created 12/20/2004 10:37:14 AM (Prassi/Veritas driver for win 2K)
File 'Drivers\InCDfs.SYS': Ver=4, 3, 23, 2, size=102016 bytes, created 3/23/2006 5:15:58 PM (InCD4 driver for win NT/2K/XP)
File 'Drivers\InCDpass.SYS': Ver=4, 3, 23, 2, size=29440 bytes, created 3/23/2006 5:15:56 PM (InCD4 driver for win NT/2K/XP)
File 'Drivers\InCDrec.SYS': Ver=4, 3, 23, 2, size=8704 bytes, created 3/23/2006 5:00:28 PM (InCD4 driver for win NT/2K/XP)
Registry Keys:
HKLM\Software\Microsoft\Windows NT\CurrentVersion\WinLogon\AllocateCDROMs : 0 (Security Option)
|
|
talone
Newbie
|
29. March 2007 @ 08:07 |
Link to this message
|
|
- I have kept and used Decrypter as it is used in conjunction with RipIt4Me and FixVTS when I had troublesome conversions.
- I don?t know Max speed of various discs used because I always run them at 4x or less, and also do Full erase.
|
Senior Member
|
29. March 2007 @ 13:21 |
Link to this message
|
File 'Drivers\InCDfs.SYS': Ver=4, 3, 23, 2, size=102016 bytes, created 3/23/2006 5:15:58 PM (InCD4 driver for win NT/2K/XP)
File 'Drivers\InCDpass.SYS': Ver=4, 3, 23, 2, size=29440 bytes, created 3/23/2006 5:15:56 PM (InCD4 driver for win NT/2K/XP)
File 'Drivers\InCDrec.SYS': Ver=4, 3, 23, 2, size=8704 bytes, created 3/23/2006 5:00:28 PM (InCD4 driver for win NT/2K/XP)
alright, u dont want these installed, so use this tool to get rid of them
http://www.nero.com/nero7/enu/InCD_CleanTool.html
Not sure about the version(if it has bugs) i do know 6.0.0.18 is the best of Nero 6 so u can use this tool to uninstall ur current version
http://www.nero.com/nero7/enu/Nero_6_CleanTool.html
then DL this version and install
http://filehippo.com/download_nero_burning_rom/?539
also dont install inCD drivers
Disc Manufacturer: CMC MA - G. AM3
these are the worst, try those Ritek ones instead
Also if u dont want to update ur firmware pick up some verbatims(best chance of working if u dont want to update ur firmware)
u should use IMGburn rather than decrypter, these 2 made by the same person plus IMGburn is updated.
edit
before buying a new burner u should try the firmware update and see if that helps, it should as u current firmware is 4 behind the newest.
Quick explanation of what firmware is
It helps the burner recognize the newer media that comes out and also helps the write(burn) strategies for the newer media
"When I look at the smiles on all the childrens faces, I just know theyre about to jab me with something."- Homer Simpson
This message has been edited since posting. Last time this message was edited on 29. March 2007 @ 13:26
|
|
pieman
Senior Member
2 product reviews
|
29. March 2007 @ 13:36 |
Link to this message
|
have you tried a differant burner?might be worth doing a chekdisc on your hard drive, and burning a little faster ie use 16x burn at 12/8x etc>but its that clicking noise thats worrying.I use decypter/anydvd to rip, and clone dvd2 to burn (I hate Nero), you could try that combo using the trial versions, but you must use decent media..taiyo yuden or verbatim.Burning can be real weird, im fine with everything bar a dvdrw or a cdrw....never been successful but i can live with that.Best of luck
pork pie,fish pie,cherry pie,hairy pie.Ill eat em all
|
|
talone
Newbie
|
30. March 2007 @ 08:44 |
Link to this message
|
|
- I have not purchased taiyo yuden or verbatim yet.
- I don?t have access to anyone?s burner near by.
- I haven?t tried any of the other suggested programs or to try different speeds because I can?t get past the frozen orange lite and clicking sound.
- What?s caught my eye in the ?log? is one of the results: ?Recorder State: Failed.? And I?ve yet to find an explanation of it.
|
|
pieman
Senior Member
2 product reviews
|
30. March 2007 @ 11:44 |
Link to this message
|
|
have you flashed the drive with the latest firmware as suggested earlier?
pork pie,fish pie,cherry pie,hairy pie.Ill eat em all
|
|
talone
Newbie
|
30. March 2007 @ 18:04 |
Link to this message
|
- I installed the Firmware update, Shut Down, and Re-started, no problem.
- Inserted -R Memorex
- Green to orange and clicking sound and after about minute went back to green.
- Opened Nero. Cliked Disc Info. Says ?No disc inserted or drive not ready. Please try again.?
- Re-insert disc, G to O and cliking and back to G.
- Open Nero. Again cliked Disc Info and again ?No disc.....?
- Instead tried Burn. Immediately ejected disc, ?Waiting for disc?, Please insert...?
- Closed Nero.
- Inserted -RW Fujifilm
- G to O and cliking for about 1 minute, back to G.
- Opened Nero to burn. Cliked Disc Info. Says ?No disc inserted or drive not ready. Please try again.?
- Re-inserted disc. Cliked to Refresh. O to G. Cliked Disc Info. ?No disc....?
- Try Burn instead again. Ejected.
|
|
talone
Newbie
|
30. March 2007 @ 19:44 |
Link to this message
|
|
Here's something huh?
- I put a Movie in DVD Burner ?G?
- Green to O to G
- I ?Explore? G Drive, got Audio_TS and Video_TS folders, Explore Video_TS and got individual files.
- and then got message no disc in G.
- Re-inserted movie, and Played a VTS with WinDVD.
- Burner lite flashing rapidly G,O,G but played ok.
- Inserted blank -RW TDK and had the same "No disc..." results as in previous Reply.
- Inserted disc again, same G to O and after a pause to G.
- Opened Decrypter
- Says ?Device not Ready [Medium Not Present]
|
|
pieman
Senior Member
2 product reviews
|
31. March 2007 @ 02:30 |
Link to this message
|
|
Its really a process of elimination here, i had a recent problem with two new pioneer burners that wouldnt work unless they were the only device on the ide channel.A new mother board sorted that as the ide controller was buggered.But starting from the beginning, chechk your cables,try a system restore,must try differant media (even just one disc) but you really need to try a diff burner, if only to eliminate yours from the equation.You can try everything you like but if the burners buggered it dont matter what you do.Its a pain i know, my fave is to start with a system restore then a full reinstall.That way you know that your starting off pretty sterile.
pork pie,fish pie,cherry pie,hairy pie.Ill eat em all
|
Senior Member
|
31. March 2007 @ 06:57 |
Link to this message
|
|
- Inserted -R Memorex
still not good disks, try verbatims
have you tried IMGburn yet?
Did you uninstall the INcd drivers?
"When I look at the smiles on all the childrens faces, I just know theyre about to jab me with something."- Homer Simpson
This message has been edited since posting. Last time this message was edited on 31. March 2007 @ 06:58
|
|
talone
Newbie
|
31. March 2007 @ 10:25 |
Link to this message
|
- I Uninstalled Burner, Removed USB cable, unplugged
- Did System Restore to date before pblm - [ 1st time, apprehensive about might have lost. As I see things noted [2], can I safely Delete originals?]
- hooked up again and Re-installed Burner
- Downloaded & re-installed Firmware update
- I had mistakenly installed Incd when I?d installed Nero Update. But then I?d Uninstalled per prior recommendation.
I did a Incd Search & got this:
ASTIncDec.class, ASTPostIncDec.class, ASTPreIncDec.class all in folder com/motive/JSInterp
What do I do with them?
- I installed IMGburn [Does it work with FixIt4Me & FixVTS?]
- I inserted a -RW Fujifilm that has accepted video and been erased a couple of times.
- unable to get to town yet for Verbatim or to borrow different burner
- G to O, stays O and clicks same as before. Then back to G.
- Opened IMGburn, says Device not Ready. Medium not Present.
- Checked Disc Info says ?No disc inserted or drive not ready. Please try again.?
- Basic pblm still the same.
|
|
talone
Newbie
|
6. April 2007 @ 17:45 |
Link to this message
|
|
My problem appears to be resolved by using Verbatim dvds, as recommended.
Although I now get ?Unknown BurnPhase?, as have other submittals, the Burn is successful.
Thank you for your interest in resolving my problem.
|
|
Advertisement
|
|
|
|
cornwell
Newbie
|
8. April 2007 @ 14:23 |
Link to this message
|
I seem to be having somewhat a similar problem. I apologize for having such a huge forum post but I can't figure it out. Would someone mind helping?
My best guess is that the new DRM on the disc's is causing them not to burn correctly but i'm not sure.
Windows XP 5.1
IA32
WinAspi: File 'Wnaspi32.dll': Ver=4.60 (1021), size=45056 bytes, created 9/10/1999 6:06:00 AM
ahead WinASPI: File 'C:\Program Files\Ahead\Nero\Wnaspi32.dll': Ver=2.0.1.74, size=164112 bytes, created 10/26/2004 5:35:34 PM
Nero API version: 6.6.0.2
Using interface version: 6.3.1.4
Installed in: C:\Program Files\Ahead\Nero\
Application: ahead\Nero - Burning Rom
Recorder: <SONY DVD RW DRU-720A> Version: JY02 - HA 1 TA 1 - 6.6.0.2
Adapter driver: <atapi> HA 1
Drive buffer : 2048kB
Bus Type : default (0) -> ATAPI, detected: ATAPI
=== Scsi-Device-Map ===
DiskPeripheral : HDS722580VLAT20 atapi Port 0 ID 0 DMA: On
DiskPeripheral : WDC WD3000JB-00KFA0 atapi Port 0 ID 1 DMA: On
CdRomPeripheral : AOPEN DVD1648/AAP atapi Port 1 ID 0 DMA: On
CdRomPeripheral : SONY DVD RW DRU-720A atapi Port 1 ID 1 DMA: On
=== CDRom-Device-Map ===
AOPEN DVD1648/AAP D: CDRom0
SONY DVD RW DRU-720A E: CDRom1
=======================
AutoRun : 1
Excluded drive IDs:
WriteBufferSize: 83886080 (0) Byte
ShowDrvBufStat : 0
BUFE : 0
Physical memory : 1023MB (1048048kB)
Free physical memory: 402MB (412416kB)
Memory in use : 60 %
Uncached PFiles: 0x0
Use Inquiry : 1
Global Bus Type: default (0)
Check supported media : Disabled (0)
8.4.2007
NeroAPI
4:23:00 PM #1 Phase 112 File APIProgress.cpp, Line 276
DVD-Video files reallocation started
4:23:00 PM #2 Phase 114 File APIProgress.cpp, Line 276
DVD-Video files reallocation completed (no file modified)
4:23:00 PM #3 Phase 111 File APIProgress.cpp, Line 276
DVD-Video files sorted
4:23:00 PM #4 Text 0 File Reader.cpp, Line 127
Reader running
4:23:00 PM #5 Text 0 File Writer.cpp, Line 122
Writer SONY DVD RW DRU-720A running
4:23:00 PM #6 Text 0 File AudioCompilationImpl.cpp, Line 842
DRM: StartDrmRecording(RealRec:1, ImageRec:0, Copies:1)
DRM: Beginning burn process.
4:23:00 PM #7 ISO9660GEN -11 File geniso.cpp, Line 3286
First writeable address = 0 (0x00000000)
4:23:00 PM #8 ISO9660GEN -11 File geniso.cpp, Line 3286
First writeable address = 0 (0x00000000)
4:23:00 PM #9 Text 0 File Burncd.cpp, Line 3117
Turn on Disc-At-Once, using DVD media
4:23:00 PM #10 Text 0 File DlgWaitCD.cpp, Line 256
Last possible write address on media: 2298495 (510:46.45, 4489MB)
Last address to be written: 2286143 (508:01.68, 4465MB)
4:23:00 PM #11 Text 0 File DlgWaitCD.cpp, Line 268
Write in overburning mode: NO
4:23:00 PM #12 Text 0 File DlgWaitCD.cpp, Line 2309
Recorder: SONY DVD RW DRU-720A, Media type: DVD-R
Disc Manufacturer: MCC 03 - RG20
Disc Application Code: 64, Disc Physical Code: 193
4:23:00 PM #13 Text 0 File DlgWaitCD.cpp, Line 430
>>> Protocol of DlgWaitCD activities: <<<
=========================================
4:23:00 PM #14 Text 0 File ThreadedTransferInterface.cpp, Line 844
Setup items (after recorder preparation)
0: TRM_DATA_MODE1 ()
2 indices, index0 (150) not provided
original disc pos #0 + 2286144 (2286144) = #2286144/508:1.69
relocatable, disc pos for caching/writing not required/ required, no patch infos
-> TRM_DATA_MODE1, 2048, config 0, wanted index0 0 blocks, length 2286144 blocks [SONY DVD RW DRU-720A]
--------------------------------------------------------------
4:23:00 PM #15 Text 0 File ThreadedTransferInterface.cpp, Line 1047
Prepare recorder [SONY DVD RW DRU-720A] for write in CUE-sheet-DAO
DAO infos:
==========
MCN: ""
TOCType: 0x00; Session Closed, disc fixated
Tracks 1 to 1:
1: TRM_DATA_MODE1, 2048/0x00, FilePos 0 0 4682022912, ISRC ""
DAO layout:
===========
__Start_|____Track_|_Idx_|_RecDep_|_CtrlAdr_
0 | lead-in | 0 | 0x00 | 0x41
0 | 1 | 0 | 0x00 | 0x41
0 | 1 | 1 | 0x00 | 0x41
2286144 | lead-out | 1 | 0x00 | 0x41
4:23:00 PM #16 Phase 24 File APIProgress.cpp, Line 276
Caching of files started
4:23:00 PM #17 Text 0 File Burncd.cpp, Line 4004
Cache writing successful.
4:23:00 PM #18 Phase 25 File APIProgress.cpp, Line 276
Caching of files completed
4:23:00 PM #19 Phase 36 File APIProgress.cpp, Line 276
Burn process started at 16x (22,160 KB/s)
4:23:00 PM #20 Text 0 File ThreadedTransferInterface.cpp, Line 2568
Verifying disc position of item 0 (relocatable, disc pos, no patch infos, orig at #0): write at #0
4:23:00 PM #21 Text 0 File DVDR.cpp, Line 2202
Recording mode: Sequential Recording Mode
4:23:00 PM #22 Text 0 File Mmc.cpp, Line 20869
Set BUFE: Power-Burn -> ON , Adapt writespeed to disc : ON
4:23:00 PM #23 Text 0 File DVDR.cpp, Line 2343
Start write address at LBA 0
DVD high compatibility mode: Yes
4:23:00 PM #24 Text 0 File Cdrdrv.cpp, Line 8310
---- DVD Structure: Physical Format Information (00h) ----
Layer: 0, Address: 0 (0 h), AGID: 0; Length: 2050
Book Type: DVD-R (2), Part Version: 5
Disc Size: 120 mm, Maximum Rate: <not specified> (F h)
Number of Layers: 1, Track Path: Parallel Track Path (PTP), Layer Type: recordable
Linear Density: 0,267 um/bit, Track Density: 0,74 um/track
Starting Physical Sector Number of Data Area: 30000 h (DVD-ROM, DVD-R/-RW, DVD+R/+RW)
End Physical Sector Number of Data Area: 0 h
End Sector Number in Layer 0: 0 h
Data in Burst Cutting Area (BCA) does not exist
Start sector number of the current Border-Out: 0 h
Start sector number of the next Border-In: 0 h
Media Specific [16..63]:
00 60 00 10 20 30 40 50 - 00 00 00 21 00 00 00 00 .`...0@P...!....
00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................
4:23:00 PM #25 Text 0 File DVDR.cpp, Line 5291
Drive: SONY DVD RW DRU-720A
Book Type request: DVD-ROM
Changing the Book Type was finished successfully, return code 0
4:24:08 PM #26 Text 0 File Cdrdrv.cpp, Line 1283
16:24:08.390 - SONY DVD RW DRU-720A\H1 T1 : Queue again later
4:28:57 PM #27 SCSI -1135 File Cdrdrv.cpp, Line 1431
SCSI Exec, HA 1, TA 1, LUN 0, buffer 0x010C0000
Status: 0x04 (0x01, SCSI_ERR)
HA-Status 0x00 (0x00, OK)
TA-Status 0x02 (0x01, SCSI_TASTATUS_CHKCOND)
Sense Key: 0x03 (KEY_MEDIUM_ERROR)
Sense Code: 0x0C
Sense Qual: 0x00
CDB Data: 0x2A 0x00 0x00 0x1A 0x6B 0xC0 0x00 0x00 0x20 0x00 0x00 0x00
Sense Data: 0x70 0x00 0x03 0x00 0x00 0x00 0x00 0x0A
0x00 0x00 0x00 0x00 0x0C 0x00
4:28:57 PM #28 CDR -1135 File Writer.cpp, Line 311
Write error
4:28:57 PM #29 Text 0 File ThreadedTransfer.cpp, Line 229
all writers idle, stopping conversion
4:28:57 PM #30 Text 0 File ThreadedTransfer.cpp, Line 223
conversion idle, stopping reader
4:28:57 PM #31 Text 0 File DVDR.cpp, Line 2586
EndDAO: Last written address was 1731519
4:28:57 PM #32 Text 0 File DVDR.cpp, Line 5291
Drive: SONY DVD RW DRU-720A
Book Type request: DVD-ROM
Changing the Book Type was finished successfully, return code 0
4:28:57 PM #33 Phase 38 File APIProgress.cpp, Line 276
Burn process failed at 16x (22,160 KB/s)
4:28:57 PM #34 Text 0 File AudioCompilationImpl.cpp, Line 867
DRM: DRM burn session terminated.
4:28:57 PM #35 Text 0 File AudioCompilationImpl.cpp, Line 896
DRM: Closing entire DRM handling. Bye.
Existing drivers:
File 'Drivers\ASPI32.SYS': Ver=4.60 (1021), size=25244 bytes, created 9/10/1999 6:06:00 AM
File 'Drivers\PXHELP20.SYS': Ver=2.03.28a, size=20640 bytes, created 3/23/2005 5:15:57 PM (Prassi/Veritas driver for win 2K)
Registry Keys:
HKLM\Software\Microsoft\Windows NT\CurrentVersion\WinLogon\AllocateCDROMs : 0 (Security Option)
|
|
