|
cant get pass bios once i boot up
|
|
|
donmega07
Suspended due to non-functional email address
|
26. July 2007 @ 18:54 |
Link to this message
|
i just put in new power supply.once i try to boot up ,it bootsup fine no erors but it wont go pass bios.the only thing it says is "no disk reserved for raid ,raid disabled"cant some help pls thx
|
|
Advertisement
|
|
|
|
|
ddp
Moderator
|
26. July 2007 @ 19:49 |
Link to this message
|
|
check to make certain the power & data cables are properly inserted into the hard drives.
|
|
donmega07
Suspended due to non-functional email address
|
27. July 2007 @ 06:27 |
Link to this message
|
|
rechheck cable in drive still same thing
|
AfterDawn Addict
4 product reviews
|
27. July 2007 @ 08:20 |
Link to this message
|
|
All power cables are definitely secure?
Do you use RAID?
Which power supply do you have?
|
Member
|
27. July 2007 @ 09:24 |
Link to this message
|
|
i know that this is the same thing but check ur cords something maybe be wrong or a bad cord
|
|
donmega07
Suspended due to non-functional email address
|
27. July 2007 @ 13:09 |
Link to this message
|
|
iwill try to check that,also was told maybe mine drives are connection is wrong able to try both
|
AfterDawn Addict
4 product reviews
|
27. July 2007 @ 13:28 |
Link to this message
|
|
Sorry I don't understand what you said there.
|
|
donmega07
Suspended due to non-functional email address
|
27. July 2007 @ 16:05 |
Link to this message
|
|
sorry about last message was at some one house rushing.i reconnect my cables,and tryed again still same result.what i was trying to say last time,was that someone said my drives were connect wrong.wonding could that be the prolbem?will try any thing that help
|
|
donmega07
Suspended due to non-functional email address
|
27. July 2007 @ 16:34 |
Link to this message
|
ok ihave 2 drives i unhooked my second drive now i have just one drive im trying to hook upnow if im wrong please let me know i pluged te flop drive in the first IDM SLOT,my dvd rom in the second idm slot on motherboard,and my drive in the last slot is this right? the second thing i want to mention is my dvd green light is blinking can that mean something?third,the way i have my power supply i have one of the power supply cables hooked up to the drive,floppy,and the dvd hooked up by itself on the power supply.if there any thing you see wrong let me know thx.
|
|
ddp
Moderator
|
27. July 2007 @ 18:46 |
Link to this message
|
the floppy drive does not get attached to the ide connector as it is not an ide drive. the floppy uses a 34 pin cable & the ide is 40 pin so if floppy is connected to ide1 the disconnect it now.
|
Senior Member
1 product review
|
27. July 2007 @ 20:04 |
Link to this message
|
Did the system ever work? It is possible one of your IDE are hooked up backwards like you stated. Most new systems cables are keyed to prevent this but it still happens. Dont worry your drive will not be damaged in that scenario.
Take a look at the cable and you will notice one side has a red stripe. That stripe always hooks to pin 1. Normaly on a HD or cd/dvd the red stripe will face to the power hook up. Pin 1 on the MB either has an arrow pointing to it or a number 1 stamped on it.
Floppies are the other way, away from the power hook up. (an incorrect hookup of a floppy will not prevent boot the light will just stay on.
Although this a very common thing for this issue it may not be the answear. Incorrect Attempts to overclock can also cause this. That usualy stops the system durring post
Good luck
-Del
|
AfterDawn Addict
4 product reviews
|
28. July 2007 @ 06:05 |
Link to this message
|
|
Jumper settings?
|
AfterDawn Addict
4 product reviews
|
28. July 2007 @ 07:31 |
Link to this message
|
if the DVD drive is working properly, it will flash a couple of times when you first turn the PC on, then stop flashing.
|
|
donmega07
Suspended due to non-functional email address
|
28. July 2007 @ 12:07 |
Link to this message
|
thx all my ide wasnt reading anything so i rearrange a few of them they all stared reading no problem after that thx again
|
|
Advertisement
|
|
|
|
ddp
Moderator
|
28. July 2007 @ 14:29 |
Link to this message
|
|
no problem.
|
