|
|
|
DMA-driver error, CRC error - While burning
|
|
Moderator
|
1. December 2007 @ 18:59 |
Link to this message
|
|
For this error the cause is usually hardware related - could be wrong - but yeah I'd definitely use different media.
Try this - kind of a pain but will help pin down the problem.
Switch the drives - dvd-rom to master, burner to slave - switch the jumper pins too. Now try and burn - use simulation instead of doing a straight burn.
Fails then just take out the dvd-rom and try again w/ the burner connected as slave. I'd do a simulation burn also.
Burn either a cd or dvd - you've been getting the same error for both.
|
|
Advertisement
|
|
|
|
|
glazberg
Newbie
|
2. December 2007 @ 02:12 |
Link to this message
|
@gwendolin
Quote:
In my reply on 26th I also stated that CMC mags were poor quality discs and advised to slow burn to 4X but I see that advice was given in vain...poster still using same discs and burning at 16X, as did Laddyboy on the 27th.
I haven't had the chance to buy different media yet. About the burning speed - I forgot about it, but should it really matter? If the burner works fine at X16 when it's the only thing connected to the IDE cable, shouldn't it work fine at the same speed even if something else is connected to the same cable?
|
AfterDawn Addict
|
2. December 2007 @ 02:25 |
Link to this message
|
|
Although the discs you are using say they are 16X I wouldnt advise burning at MAX speed of 16X....they are, as stated , poor quality and are prone to failing even at 4X.
I always recommend burning at 4X even with my Verbatims, after all how much time do you actually save, Cheers.
|
Moderator
|
2. December 2007 @ 04:22 |
Link to this message
|
|
@glazberg - this thread is going around in circles; by all means try 4x, until you start trying the suggestions you will still be stuck in this thread instead of watching successfully burned movies; i even dropped by to add my own personal experience on these discs, ie i was suddenly having burning problems; changed the discs back to the ones i've been using (1000s of) for years and all is well again.
you need to try 4x next and update us on your progress...
Main PC ~ Intel C2Q Q6600 (G0 Stepping)/Gigabyte GA-EP45-DS3/2GB Crucial Ballistix PC2-8500/Zalman CNPS9700/Antec 900/Corsair HX 620W
Network ~ DD-WRT ~ 2node WDS-WPA2/AES ~ Buffalo WHR-G54S. 3node WPA2/AES ~ WRT54GS v6 (inc. WEP BSSID), WRT54G v2, WRT54G2 v1. *** Forum Rules *** |
|
wdlndboy
Newbie
|
2. January 2008 @ 03:59 |
Link to this message
|
Ok guys I guess I am having the same problem. Well the other day I bought this computer off some guy I didn't even know. Yah I know stupid right well it turns out that it has all these problems like Javascript not working I have tried everything believe me everything and then when I go to use the DVD burner/Cd Burner this message pops up DMA-driver error, CRC error go this is frustrating I don't know too much about computers and I have read this whole thread plus tons more and still it makes no sense. I have tried changing my write speed but I have been unsuccessful in doing so. I can't seem to find how. Here is the log from Nero. Please someone help me!
Windows User
None
4C85-2006-3005-4001-0556-76E0-0900-4026-X8E5-**** (*)
Windows XP 5.1
IA32
WinAspi: -
ahead WinASPI: File 'C:\Program Files\Nero\Nero 7\Core\Wnaspi32.dll': Ver=2.0.1.74, size=169792 bytes, created 3/20/2007 9:09:56 AM
NT-SPTI used
Nero Version: 7.5.13.6
Internal Version: 7, 5, 13, 6
(Nero Express)
Recorder: <SONY DVD RW AW-G170A> Version: 1.62 - HA 1 TA 0 - 7.5.13.6
Adapter driver: <IDE> HA 1
Drive buffer : 2048kB
Bus Type : default (0) -> ATAPI, detected: ?
CD-ROM: <TOSHIBA DVD-ROM SD-M1202>Version: 1020 - HA 1 TA 1 - 7.5.13.6
Adapter driver: <IDE> HA 1
=== Scsi-Device-Map ===
DiskPeripheral : SAMSUNG SV1204H atapi Port 0 ID 0 DMA: On
CdRomPeripheral : SONY DVD RW AW-G170A atapi Port 1 ID 0 DMA: On
CdRomPeripheral : TOSHIBA DVD-ROM SD-M1202 atapi Port 1 ID 1 DMA: On
=== CDRom-Device-Map ===
SONY DVD RW AW-G170A D: CDRom0
TOSHIBA DVD-ROM SD-M1202 E: CDRom1
=======================
AutoRun : 1
Excluded drive IDs:
WriteBufferSize: 73400320 (0) Byte
BUFE : 0
Physical memory : 503MB (515608kB)
Free physical memory: 132MB (135184kB)
Memory in use : 73 %
Uncached PFiles: 0x0
Use Inquiry : 1
Global Bus Type: default (0)
Check supported media : Disabled (0)
2.1.2008
ISO compilation
12:09:31 AM #1 Text 0 File SCSIPTICommands.cpp, Line 411
LockMCN - completed sucessfully for IOCTL_STORAGE_MCN_CONTROL
12:09:31 AM #2 Text 0 File Isodoc.cpp, Line 6517
Iso document burn settings
------------------------------------------
Determine maximum speed : FALSE
Simulate : FALSE
Write : TRUE
Finalize CD : FALSE
Multisession : TRUE
Multisession type: : Start multisession
Burning mode : DAO
Mode : 1
ISO Level : 1 (Max. of 11 = 8 + 3 char)
Character set : ISO 9660
Joliet : TRUE
Allow pathdepth more than 8 directories : TRUE
Allow more than 255 characters in path : TRUE
Write ISO9660 ;1 file extensions : TRUE
12:09:32 AM #3 ISO9660GEN -11 File Geniso.cpp, Line 3332
First writeable address = 0 (0x00000000)
12:09:32 AM #4 Text 0 File Burncd.cpp, Line 3471
Turn on Disc-At-Once, using DVD media
12:09:33 AM #5 Text 0 File DlgWaitCD.cpp, Line 306
Last possible write address on media: 2295103 (510:01.28, 4482MB)
Last address to be written: 11359 ( 2:31.34, 22MB)
12:09:33 AM #6 Text 0 File DlgWaitCD.cpp, Line 318
Write in overburning mode: NO (enabled: CD)
12:09:33 AM #7 Text 0 File DlgWaitCD.cpp, Line 2929
Recorder: SONY DVD RW AW-G170A, Media type: DVD+R
Disc Manufacturer ID: CMC MAG, Media Type ID: E01, Product revision number: 0
Disc Application Code: 0, Extended Information Indicators: 3
12:09:33 AM #8 Text 0 File DlgWaitCD.cpp, Line 490
>>> Protocol of DlgWaitCD activities: <<<
=========================================
12:09:33 AM #9 Text 0 File ThreadedTransferInterface.cpp, Line 792
Setup items (after recorder preparation)
0: TRM_DATA_MODE1 ()
2 indices, index0 (150) not provided
original disc pos #0 + 11360 (11360) = #11360/2:31.35
relocatable, disc pos for caching/writing not required/ required
-> TRM_DATA_MODE1, 2048, config 0, wanted index0 0 blocks, length 11360 blocks [D: SONY DVD RW AW-G170A]
--------------------------------------------------------------
12:09:55 AM #10 Text 0 File ThreadedTransferInterface.cpp, Line 995
Prepare [D: SONY DVD RW AW-G170A] for write in CUE-sheet-DAO
DAO infos:
==========
MCN: ""
TOCType: 0x00; Session Closed, disc fixated
Tracks 1 to 1: Idx 0 Idx 1 Next Trk
1: TRM_DATA_MODE1, 2048/0x00, FilePos 0 0 23265280, ISRC ""
DAO layout:
===========
___Start_|____Track_|_Idx_|_CtrlAdr_|_____Size_|______NWA_|_RecDep__________
0 | lead-in | 0 | 0x41 | 0 | 0 | 0x00
0 | 1 | 0 | 0x41 | 11360 | 0 | 0x00
0 | 1 | 1 | 0x41 | 11360 | 0 | 0x00
11360 | lead-out | 1 | 0x41 | 0 | 0 | 0x00
12:09:55 AM #11 Text 0 File SCSIPTICommands.cpp, Line 209
SPTILockVolume - completed successfully for FCTL_LOCK_VOLUME
12:09:55 AM #12 Phase 24 File dlgbrnst.cpp, Line 1760
Caching of files started
12:09:56 AM #13 Text 0 File Burncd.cpp, Line 4355
Cache writing successful.
12:09:56 AM #14 Phase 25 File dlgbrnst.cpp, Line 1760
Caching of files completed
12:09:56 AM #15 Phase 36 File dlgbrnst.cpp, Line 1760
Burn process started at 8x (11,080 KB/s)
12:09:56 AM #16 Text 0 File ThreadedTransferInterface.cpp, Line 2712
Verifying disc position of item 0 (relocatable, disc pos, no patch infos, orig at #0): write at #0
12:09:56 AM #17 Text 0 File Cdrdrv.cpp, Line 9261
---- DVD Structure: Physical Format Information (00h) ----
Media Type: 0, Layer: 0, Address: 0 (0 h), AGID: 0; Length: 2050
Book Type: DVD+R (10), Part Version: 1.0x (1)
Disc Size: 120 mm, Maximum Rate: <not specified> (F h)
Number of Layers: 1, Track Path: Parallel Track Path (PTP), Layer Type: recordable
Linear Density: 0,267 um/bit, Track Density: 0,74 um/track
Starting Physical Sector Number of Data Area: 30000 h (DVD-ROM, DVD-R/-RW, DVD+R/+RW)
End Physical Sector Number of Data Area: 26053F h
End Sector Number in Layer 0: 0 h (LBN: FFFD0000 h, 4193920 MB)
Data in Burst Cutting Area (BCA) does not exist
Disc Application Code: 0 / 0 h
Extended Information indicators: 3 h
Disc Manufacturer ID: CMC.MAG.
Media type ID: E01
Product revision number: 0
Number of Physical format information bytes in use in ADIP up to byte 63: 56
Media Specific [16..63]:
00 00 03 43 4D 43 20 4D - 41 47 00 45 30 31 00 38 ...CMC.MAG.E01.8
23 54 37 10 02 38 6A 02 - 88 67 15 15 0B 0B 08 08 #T7..8j..g......
01 19 1B 0C 0C 0C 0D 01 - 00 00 00 00 00 00 00 00 ................
12:09:56 AM #18 Text 0 File DVDPlusRW.cpp, Line 674
Start write address at LBA 0
DVD high compatibility mode: Yes
12:10:24 AM #19 SPTI -1502 File SCSIPassThrough.cpp, Line 179
CdRom0: SCSIStatus(x02) WinError(0) NeroError(-1502)
Sense Key: 0x04 (KEY_HARDWARE_ERROR)
Sense Code: 0x08
Sense Qual: 0x03
CDB Data: 0x2A 00 00 00 00 00 00 00 20 00 00 00
Sense Area: 0x70 00 04 00 00 00 00 0A 00 00 00 00 08 03
Buffer x22030040: Len x10000
0x00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
12:10:24 AM #20 CDR -1502 File Writer.cpp, Line 299
DMA-driver error, CRC error
D: SONY DVD RW AW-G170A
12:10:38 AM #21 Phase 127 File dlgbrnst.cpp, Line 1760
Generating DVD high compatibility borders
12:11:25 AM #22 CDR -1093 File WriterStatus.cpp, Line 162
No seek complete
D: SONY DVD RW AW-G170A
12:11:25 AM #23 TRANSFER -24 File WriterStatus.cpp, Line 162
Could not perform end of Disc-at-once
12:11:25 AM #24 Phase 38 File dlgbrnst.cpp, Line 1760
Burn process failed at 8x (11,080 KB/s)
12:11:25 AM #25 Text 0 File SCSIPTICommands.cpp, Line 254
SPTIDismountVolume - completed successfully for FSCTL_DISMOUNT_VOLUME
12:11:30 AM #26 Text 0 File Cdrdrv.cpp, Line 10538
DriveLocker: UnLockVolume completed
12:11:30 AM #27 Text 0 File SCSIPTICommands.cpp, Line 411
UnLockMCN - completed sucessfully for IOCTL_STORAGE_MCN_CONTROL
Existing drivers:
Registry Keys:
HKLM\Software\Microsoft\Windows NT\CurrentVersion\WinLogon\AllocateCDROMs : 0 (Security Option)
|
Moderator
|
2. January 2008 @ 13:53 |
Link to this message
|
|
@wdlndboy
Sounds like you have much more going on then meets the eye.
You'll need to start a new thread for your problem. Makes things less confusing and forum rules.
Try the other suggestions in this thread too - different media, check the jumper settings etc.
|
AfterDawn Addict
1 product review
|
2. January 2008 @ 14:58 |
Link to this message
|
@wdlndboy
Beside getting good media( which is more than recommended, but I doubt it will fix your problem since is a hardware(burner/cables...) issue, here are some fixes that worked for other people ( I don't know if this is a repeat, didn'ttake the time to read through the first 2 pages of this thread. Next time don't hijack someone else's thread, start your own like binkie said)
Quote:
Sense Key: 0x04 (KEY_HARDWARE_ERROR)
Sense Code: 0x08
Sense Qual: 0x03
This also translates into "LOGICAL UNIT COMMUNICATION CRC ERROR (ULTRA-DMA/32) (040803), which means the data can't be properly verified between the hard drive and the burner, there is poor communication. If you have a 40-pin cable, you might have to change it for a 80-pin( it might be as simple as that). Also you might have to reconfigure the 2 drives-reader and burner-(master/slave setup).
http://club.cdfreaks.com/f44/sony-dru-72...40803-a-133258/
@glazberg
you got a new cable. Is it a 80-pin? You might need that instead of 40-pin
http://forums.speedlabs.org/index.php?topic=1056.msg12669
|
|
Advertisement
|
|
|
|
glazberg
Newbie
|
3. January 2008 @ 02:04 |
Link to this message
|
Quote:
you got a new cable. Is it a 80-pin? You might need that instead of 40-pin
I replaced the cable (don't know if it's 40 or 80 pins), and connected only the DVD burner to it. Sicne that worked, and when I tried reconnecting the other DVD drive it didn't work, I figured I don't really need the other DVD drive...
Yeah, I know that's lame, but at least I can burn....
|
|
