|
decrypter problems
|
|
|
luminox
Suspended due to non-functional email address
|
14. December 2005 @ 01:45 |
Link to this message
|
|
has anybody had the problem where when decrypter is ready to burn, and it says writing leadin but never starts to iniate the burn process? have had that happen now with lost in translation and the island. just wondering what was up with that
|
|
Advertisement
|
|
|
|
AfterDawn Addict
|
14. December 2005 @ 02:11 |
Link to this message
|
|
No, I haven't. Do you get any type of error message?
|
|
luminox
Suspended due to non-functional email address
|
14. December 2005 @ 20:56 |
Link to this message
|
|
no type of error message at all, it just says writing lead in at the bottom left corner of decrypt and the time counter continues to roll but it never starts to actually burn. I have done many backups before and never encountered this problem.
|
AfterDawn Addict
|
14. December 2005 @ 23:06 |
Link to this message
|
No, I've never experienced that kind of problem before. Why don't you try to uninstall DVD Decrypter and reinstall it again, then give it another shot.
By the way, The Island has no special protections whatsoever. I ripped it with DVD Decrypter via Mode, File F successfully, encoded with Nero Recode2 with "Advanced Analysis" and burned it with Nero Burning Rom.
|
|
luminox
Suspended due to non-functional email address
|
14. December 2005 @ 23:29 |
Link to this message
|
|
i'll try uninstalling it and run it again, also under the settings for decrpyt do you have the remove puo and bup under the file tab i think and also the iso read+write tabs selected or no, and does it make a difference? thanx for your time and input guys.
|
AfterDawn Addict
|
15. December 2005 @ 00:05 |
Link to this message
|
Try the following settings inside DVD Decrypter in prior to the ripping process. That's what I have mine set and I can rip nearly 99% of the movies flawlessly.
*NOTE: in prior to the ripping part, let?s tweak/set a few settings inside DVD Decrypter*
** open up DVD Decrypter, go to Tools, and Settings
** at General on ?Removal Method? arrow down to ?Aggressive?
** at I/O, check ?Ignore Read Errors?
** at ?File Mode? check on all of the Remove, Ignore, Patch and Create MDS file.
** at CSS check ?Brute Force -->I/O key exchange,
On Failure: use key from another file [YES]
** at ?ISO Read Mode? check on all Remove and Create MDS file
Once you?re done with the settings, click OK to get out from the settings.
Happy burning!!!
|
|
luminox
Suspended due to non-functional email address
|
15. December 2005 @ 01:24 |
Link to this message
|
|
thanx a million for showing me that!
|
AfterDawn Addict
|
15. December 2005 @ 02:08 |
Link to this message
|
|
@luminox
Did the problem get corrected?
|
|
luminox
Suspended due to non-functional email address
|
15. December 2005 @ 21:28 |
Link to this message
|
|
yes, i did thanx for the help
|
AfterDawn Addict
|
15. December 2005 @ 21:35 |
Link to this message
|
Quote:
thanx a million for showing me that!
yes, i did thanx for the help
You're welcome. Like ddp said; "teach and learn". I primarily used my method of settings as shown above on DVD Decrypter when ripping using Mode, File F and nearly 99% of the times, DVD Decrypter will rip it flawlessly.
|
|
Advertisement
|
|
|
AfterDawn Addict
|
16. December 2005 @ 02:55 |
Link to this message
|
|
I agree, that's how I have mine set up too. I haven't had an issue rippin in forever.
Cheers.
@alkohol
I added you to my BL :)
|
