|
The best Blank Media/Software??
|
|
|
doorpro
Junior Member
|
13. February 2006 @ 10:06 |
Link to this message
|
|
Hi,
I am struggling with problematic DVD copies and although I and using TY blank media which are reportedly the best I still get movies stopping/freezing/skipping in the last chapter or two.
I have always used DVDShrink and lately I have tried almost every type of software out there including AnyDVD, DVDFab, Nero 6.6, Clone DVD2,VOBBlanker and DVD Decrypter still to have troubled copies.
My two dvd drives I am told are some of the best also, the first being a Plextor PX-504A and my latest addition is a Sony DW-Q30A which is a dual layer writer.
Therefore, can anyone please tell me which software to use and what other programs to use in conjunction with it so that I can enjoy almost flawless copies just as others in this forum claim to have and of course i would have to accept a small percantage of errors cause lets face it we all need coasters but I am getting about 50% bad and they all check out until i get 9/10ths of the way through watching them.
All the best,
Doug
This message has been edited since posting. Last time this message was edited on 13. February 2006 @ 10:08
|
|
Advertisement
|
|
|
|
Member
|
13. February 2006 @ 10:10 |
Link to this message
|
|
I use Imation DVD-Rs & no lemons yet (just ate threw a 100 pack).
What is your most recent movie? & what speed do you write at?
AMD Athlon 64 3800 X2, 1GB RAM, 200GB HDD.
|
|
alpsig
Member
|
13. February 2006 @ 10:33 |
Link to this message
|
|
Sounds like a burn speed issue. What speed are you burning at?
|
Member
|
13. February 2006 @ 10:54 |
Link to this message
|
Can you post your last Nero log here, then someone will be able to assist you.
Otherwise it's only guesswork what the problem may be.
|
|
doorpro
Junior Member
|
13. February 2006 @ 11:35 |
Link to this message
|
|
Burning at Max speed I think and I'm guessing that this may be where ther problems lie. Should i slow down the burning to 2.4 perhaps?
|
|
hcekc
Junior Member
|
13. February 2006 @ 11:40 |
Link to this message
|
|
I've had problems with Maxell +R, and the printable TDK +R (100% were bad backups). The non printable TDKs are pretty good. I've had the BEST backups with, believe it or not, Fuji Film +R.
|
Member
|
13. February 2006 @ 11:47 |
Link to this message
|
|
4x should be fine which is what I use.
AMD Athlon 64 3800 X2, 1GB RAM, 200GB HDD.
|
|
alpsig
Member
|
13. February 2006 @ 11:49 |
Link to this message
|
|
Yes, change your burn speed to 4x. This should clear up your issues at the end of the burn process.
|
|
doorpro
Junior Member
|
13. February 2006 @ 11:54 |
Link to this message
|
|
Thank you guys I will try that.......
|
AfterDawn Addict
|
13. February 2006 @ 13:10 |
Link to this message
|
|
How close to the edge are you burning since it's the last chapters that are problematic. Try setting at 4300.
|
|
doorpro
Junior Member
|
13. February 2006 @ 13:29 |
Link to this message
|
I already do that thanks..... I figured that DVD Shrink maybe trying to cram as much in as possible so i always make it custom...
|
|
Advertisement
|
|
|
Moderator
1 product review
|
13. February 2006 @ 13:31 |
Link to this message
|
|
If the compression is high ( I consider high 75% and above) use the Deep Analysis and AEC controls, these settings may smooth out the problems you are experiencing.
|
