|
Discs not spinning anymore!!!
|
|
|
Goblin82
Newbie
|
3. August 2006 @ 16:16 |
Link to this message
|
|
Hey, I have swap magic and the sensor blockers but one broke (the one that checks the cd cover) Anyway i got the bright idea to open up the ps2 and make the little button for the cd cover check stick. when I replaced the whole thing with the screws, the cd won't spin at all now, even with the cover down. Any Ideas?
|
|
Advertisement
|
 |
|
|
Member
|
3. August 2006 @ 21:08 |
Link to this message
|
|
You must've hit something, are you sure you didn't accidently knock one of the three sensors off while fixing the one?
V12 PS2 - DMS4 SE PRO, Diode Fix, HDconnect, 320gb HD
----------------
Tall Israeli: For anyone who doesn't smoke, this is like your mom taking your dreamcast away.
Wagh: god you're an idiot.
|
|
Goblin82
Newbie
|
4. August 2006 @ 13:17 |
Link to this message
|
|
well, I took all the sensors off now and even tried with a valid PS2 disc but it won't spin either.... I do remember accidently moving the thing for the lense, like the lense mechanism that makes the lense move.
|
Member
|
4. August 2006 @ 13:48 |
Link to this message
|
|
Does everything else run fine ie: the browser startup sequence, recognition of memory cards?
V12 PS2 - DMS4 SE PRO, Diode Fix, HDconnect, 320gb HD
----------------
Tall Israeli: For anyone who doesn't smoke, this is like your mom taking your dreamcast away.
Wagh: god you're an idiot.
|
|
Goblin82
Newbie
|
5. August 2006 @ 05:33 |
Link to this message
|
|
yes the boot up works fine... there is however the sensor that detects if there is actually a cd in the system. could I have knocked something off on the board or misplaced something that would screw up the sensors. I followed the instructions on the net about taking the screws off, flipping the ps2 over and then taking off the casing starting from the left top corner.
Sorry for being such a newb.
|
Member
|
5. August 2006 @ 11:52 |
Link to this message
|
|
Make sure all your cables are plugged in properly, there is one located under the laser reader itself.
Search google for the location of all of them.
V12 PS2 - DMS4 SE PRO, Diode Fix, HDconnect, 320gb HD
----------------
Tall Israeli: For anyone who doesn't smoke, this is like your mom taking your dreamcast away.
Wagh: god you're an idiot.
|
|
Goblin82
Newbie
|
6. August 2006 @ 06:43 |
Link to this message
|
|
yes everything is connected correctly. This really pisses me off when I can't figure something out, I don't really care about the PS2, I can just buy another one. But not figuring out this problem is what's bothering me the most.
|
|
lilg_06
Senior Member
|
13. August 2006 @ 06:06 |
Link to this message
|
|
Are the sensor switches still working properly, when you push them down to they come back up, and when you opened up the system, what did you do to stick the sensor down?
|
|
Baller25
Newbie
|
18. August 2006 @ 19:58 |
Link to this message
|
|
i have a ps2 slim v12 that does not spin any disk even
if the door is closed and i think i have the same problem as Goblin as i think i broke the 3 sensor like Goblin. Can someone help me!!
This message has been edited since posting. Last time this message was edited on 18. August 2006 @ 23:14
|
|
lilg_06
Senior Member
|
19. August 2006 @ 03:21 |
Link to this message
|
|
If you have broken one of the sensor switches, open up the console, and locate the two, and check to see if they are damaged.
|
|
Baller25
Newbie
|
19. August 2006 @ 13:32 |
Link to this message
|
|
i only broke sensor c as it does not spring up and now there is a little hole where the metal part is suppose to pop up; i think. is there anyway to fix it or is there another problem? any information would be helpful.
|
|
lilg_06
Senior Member
|
19. August 2006 @ 14:07 |
Link to this message
|
|
Yes, there are two terminals in there, you can use foil to connect them together and put tape over it, or solder a single wire to connect the 2 together, and i tell you that it will work. I have made this repair for mates several of times.
|
|
Baller25
Newbie
|
19. August 2006 @ 14:23 |
Link to this message
|
|
Thanks Lilg, but how would i go about doing this..can i receive a guide or step by step instructions on how to do it. Thanks
|
|
lilg_06
Senior Member
|
19. August 2006 @ 14:42 |
Link to this message
|
|
Hmmm, well i can help you through it if you want, PM me your hotmail/yahoo email address if you want me to guide you through, otherwise i can get you some pic up tomorrow on how to do it.
|
|
Advertisement
|
|
|
|
Baller25
Newbie
|
19. August 2006 @ 15:34 |
Link to this message
|
|
ok, i do just that and pm you...thanks
|
