|
Burning xbox 360 problems.
|
|
|
Vladaron
Newbie
|
26. November 2006 @ 07:45 |
Link to this message
|
I have a pioneer 109 dvd burner with FW 1.58, which in the specs burns DL discs, I am using DVD+R Dual layer discs. I have downloaded the clonecd program and followed the instructions in this topic.
However I keep getting the messages of "writing to PIONEER DVD-RW DVR-109 FAILED!" after about 25 minutes of burning. I set the burning speed to x2 and followed instructions to the word.
Any ideas? need to upgrade my burner? discs?
http://img134.imageshack.us/my.php?image=clonefaultrq6.jpg
there is the log on that screenshot ^^ that might help.
downloaded Rainbow six, repaired the files, extracted them into a 000 file (7.3GB) and a dvd file (1KB). I then pressed "write from image" in clonecd and used the browser to find the DVD file then selected my burner to burn the file to. Is burning the DVD file correct or have I made a mistake and must burn the 000 file?
The progress meter in clonecd was at 100% when i came back to my computor but it said it had failed to write to my burner.
I have no idea where/what i am going wrong, if you need any more infomation from me just fire away with questions.
thanks.
|
|
Advertisement
|
|
|
|
|
backup
Suspended due to non-functional email address
|
26. November 2006 @ 07:50 |
Link to this message
|
Originally posted by Vladaron:
I have a pioneer 109 dvd burner with FW 1.58, which in the specs burns DL discs, I am using DVD+R Dual layer discs. I have downloaded the clonecd program and followed the instructions in this topic.
However I keep getting the messages of "writing to PIONEER DVD-RW DVR-109 FAILED!" after about 25 minutes of burning. I set the burning speed to x2 and followed instructions to the word.
Any ideas? need to upgrade my burner? discs?
http://img134.imageshack.us/my.php?image=clonefaultrq6.jpg
there is the log on that screenshot ^^ that might help.
downloaded Rainbow six, repaired the files, extracted them into a 000 file (7.3GB) and a dvd file (1KB). I then pressed "write from image" in clonecd and used the browser to find the DVD file then selected my burner to burn the file to. Is burning the DVD file correct or have I made a mistake and must burn the 000 file?
[b]The progress meter in clonecd was at 100% when i came back to my computor but it said it had failed to write to my burner[/b].
I have no idea where/what i am going wrong, if you need any more infomation from me just fire away with questions.
thanks.
did you try the disc??? also what layer break info is clonecd showing when you load the file?? repaired the file ??
This message has been edited since posting. Last time this message was edited on 26. November 2006 @ 07:52
|
|
Vladaron
Newbie
|
26. November 2006 @ 07:54 |
Link to this message
|
|
Info shown on clonecd at the browsing screen.
Info on Image File:
Sectors: 3697696
LayerBreak: 1913760
yes i repaired the file before extracting it.
|
|
backup
Suspended due to non-functional email address
|
26. November 2006 @ 08:03 |
Link to this message
|
|
surly if it was downloaded everything would be done ??? just a matter of burning the .dvd file
This message has been edited since posting. Last time this message was edited on 26. November 2006 @ 08:03
|
|
Vladaron
Newbie
|
26. November 2006 @ 08:05 |
Link to this message
|
|
I have no idea, but is something wrong with my burner?my disc im using or the clonecd program? i have version 5.2.9.1.
any ideas on what it could be?
|
|
backup
Suspended due to non-functional email address
|
26. November 2006 @ 08:09 |
Link to this message
|
Originally posted by Vladaron:
I have no idea, but is something wrong with my burner?my disc im using or the clonecd program? i have version 5.2.9.1.
any ideas on what it could be?
most burners will do the deed what media was you using the dye info?? you could always try imgburn as a second resort
This message has been edited since posting. Last time this message was edited on 26. November 2006 @ 08:09
|
|
mrlip
Senior Member
|
26. November 2006 @ 08:09 |
Link to this message
|
Vladaron is my mate and was telling me of his problem yesterday. I told him to flash the firmware on his Pioneer which he has done. That didnt work. His clone cd is registered. Its the same version as mine and I am burning flawless backups on a Pioneer 108. He was telling me his backups are failing at about 50-55% which defo sounds like his burner is having trouble switchin layers. Does anyone know if FAT32 file systems have trouble burning dual layer images?Because i know they have trouble handling big files. Just a long shot. Also, think the DVD decyrpter method of burning is worth a shot?
EDIT: Backup, his dvd's are same as mine, Ricoh Japan DVD+R DL. Dye info RICOHJPND000
This message has been edited since posting. Last time this message was edited on 26. November 2006 @ 08:10
|
|
backup
Suspended due to non-functional email address
|
26. November 2006 @ 08:20 |
Link to this message
|
|
i have read on some forums to keep away from the richon media ,, but saying this i burned 4 backups with cmc mag earlier... which is supposed to be crap ... on the svp site for media they also slate the richon media for backups .....
but each to there own :)
|
|
Vladaron
Newbie
|
26. November 2006 @ 08:25 |
Link to this message
|
Originally posted by backup:
i have read on some forums to keep away from the richon media ,, but saying this i burned 4 backups with cmc mag earlier... which is supposed to be crap ... on the svp site for media they also slate the richon media for backups .....
but each to there own :)
but mrlip has no problems whatsoever with that media yet i have 4 coasters, I don't think it is the discs. Clonecd seems to be my guess but i don't know how to find out and deal with it.
what media would you recommend?
|
|
backup
Suspended due to non-functional email address
|
26. November 2006 @ 08:30 |
Link to this message
|
|
okay try imgburn to burn the file .... it is freeware do you know how to set it up??
media can differ for everyone it depends on your setup and your drive but most of all the xbox drive as got to read them.
This message has been edited since posting. Last time this message was edited on 26. November 2006 @ 08:32
|
|
Vladaron
Newbie
|
26. November 2006 @ 08:32 |
Link to this message
|
|
No im afraid not, could you help? where do i get it from and use it etc?
Thanks for your patience and help.
|
|
backup
Suspended due to non-functional email address
|
26. November 2006 @ 08:34 |
Link to this message
|
|
This message has been edited since posting. Last time this message was edited on 26. November 2006 @ 08:47
|
|
Vladaron
Newbie
|
26. November 2006 @ 08:35 |
Link to this message
|
|
thanks, i will let you know how i get on.
|
|
mrlip
Senior Member
|
26. November 2006 @ 08:48 |
Link to this message
|
|
Its Ricoh media not Ricon. Made in Japan, very good quality, more expensive than Verbatim!
|
|
backup
Suspended due to non-functional email address
|
26. November 2006 @ 08:53 |
Link to this message
|
|
it may not be the discs as mentioned but if i had the choice between the ricoh and verbs i would indeed choose the verbs they seem to be more flexable on the 360 drives but like i say i used some crappy cmc mag media and they seem to work flawless :)
|
|
Vladaron
Newbie
|
26. November 2006 @ 09:09 |
Link to this message
|
|
Same as before, gets to about 50-55% then write speed drops to zero and then nothing.
W 18:57:34 Failed to Write Sectors 1915552 - 1915583 - Write Error
W 18:57:34 Retrying (1 of 20)...
^^in the log
Any more ideas, wearing me down this.
|
|
backup
Suspended due to non-functional email address
|
26. November 2006 @ 09:19 |
Link to this message
|
|
are you trying to burn the same file each time it just may be corrupted?? ...thats the problem with downloads.. im sorry im at a loss :( did you manually enter the layer break in imgburn?
This message has been edited since posting. Last time this message was edited on 26. November 2006 @ 09:20
|
|
Vladaron
Newbie
|
26. November 2006 @ 09:22 |
Link to this message
|
Originally posted by backup:
are you trying to burn the same file each time it just may be corrupted?? ...thats the problem with downloads.. im sorry im at a loss :( did you manually enter the layer break in imgburn?
No the layerbreak was already there i have done nothing manually. I tried a different file that contained the game F.E.A.R, same result. I have no idea what to do.
|
|
Siph3r
Newbie
|
30. November 2006 @ 07:04 |
Link to this message
|
|
i'm having exactly the same program using the same DVD burner. around the 50-55% mark the error occurs.
otto
|
|
mrlip
Senior Member
|
30. November 2006 @ 08:14 |
Link to this message
|
|
For anyones info, Vladaron fixed his problem by buying a Pioneer111D from SVP. £20 if you live in the UK. Sorted. Burning games flawlessly now.
|
|
backup
Suspended due to non-functional email address
|
30. November 2006 @ 08:16 |
Link to this message
|
|
thanks for the update dude
|
|
mwr_allen
Junior Member
|
8. December 2006 @ 02:54 |
Link to this message
|
I am trying to burn gears of war .000 image with DVD Decrypter but i get an error message with
i/o error
device [1:1:0] HP DVD WRITER 840b HJ86 (F:) (ATA)
ScsiStatus: 0x02
Interpretation: Check Condition
CDB: BF 00 00 00 00 00 20 0C 00 00
Interpretation: Send DVD Structure - DVD+R DL Boundary Information
Sence Area: 70 00 05 00 00 00 00 0E 00 00 00 00 24 00 00 00 00 00
Interpretation Field in cdb
I followed a tutorial on entering the layer break info into the dvd write mode tab of DVD Decrypter settings and saving the dvd file again as IMAGE_DVDDECRYPTER.
Please can anyone help with this or is it just my dvd writer?
Thank you.
monkey magic
|
|
backup
Suspended due to non-functional email address
|
8. December 2006 @ 08:31 |
Link to this message
|
Originally posted by mwr_allen:
I am trying to burn gears of war .000 image with DVD Decrypter but i get an error message with
i/o error
device [1:1:0] HP DVD WRITER 840b HJ86 (F:) (ATA)
ScsiStatus: 0x02
Interpretation: Check Condition
CDB: BF 00 00 00 00 00 20 0C 00 00
Interpretation: Send DVD Structure - DVD+R DL Boundary Information
Sence Area: 70 00 05 00 00 00 00 0E 00 00 00 00 24 00 00 00 00 00
Interpretation Field in cdb
I followed a tutorial on entering the layer break info into the dvd write mode tab of DVD Decrypter settings and saving the dvd file again as IMAGE_DVDDECRYPTER.
Please can anyone help with this or is it just my dvd writer?
Thank you.
you are burning the wrong file select the .dvd
|
|
thought85
Newbie
|
8. December 2006 @ 12:15 |
Link to this message
|
Quote:
Originally posted by mwr_allen:
I am trying to burn gears of war .000 image with DVD Decrypter but i get an error message with
i/o error
device [1:1:0] HP DVD WRITER 840b HJ86 (F:) (ATA)
ScsiStatus: 0x02
Interpretation: Check Condition
CDB: BF 00 00 00 00 00 20 0C 00 00
Interpretation: Send DVD Structure - DVD+R DL Boundary Information
Sence Area: 70 00 05 00 00 00 00 0E 00 00 00 00 24 00 00 00 00 00
Interpretation Field in cdb
I followed a tutorial on entering the layer break info into the dvd write mode tab of DVD Decrypter settings and saving the dvd file again as IMAGE_DVDDECRYPTER.
Please can anyone help with this or is it just my dvd writer?
Thank you.
you are burning the wrong file select the .dvd
backups right don't do the .000 .dvd file=YES use that
|
|
Advertisement
|
|
|
|
mwr_allen
Junior Member
|
8. December 2006 @ 14:27 |
Link to this message
|
|
the .DVD is the one that i am trying to burn but i am getting this error.
Thanks.
monkey magic
|
