|
Eurovox 2007 Red
|
|
AfterDawn Addict
|
18. October 2007 @ 16:45 |
Link to this message
|
|
Does it have an Intel chipset or an ST one?
|
|
Advertisement
|
|
|
|
|
Jlewis
Junior Member
|
18. October 2007 @ 16:51 |
Link to this message
|
|
Hi Scouser,
ST.
I have jtagged twice and flashed all i get is number 126 on display.
Jlewis
|
|
Jlewis
Junior Member
|
18. October 2007 @ 17:09 |
Link to this message
|
|
Hi Scouser,
My head is wrecked with this IO hope that you can help.
Jlewis
|
AfterDawn Addict
|
18. October 2007 @ 17:30 |
Link to this message
|
|
Have you followed the instructions that came with the jtag? Are you using SkyMax or Jkeys and are you erasing and rewriting to the tsop or are you getting errors?
|
|
Jlewis
Junior Member
|
18. October 2007 @ 17:46 |
Link to this message
|
I follow this below however i get an error on whiteflash 80002000
run skymax
click on 2mb(ox7fe00000)
click start
click erase
click write(will ask you to load tsop flash file)
should take few minutes to write
switch the box off the on when writing is finished
the box will be up and running now
load any pre june update flash.
|
AfterDawn Addict
|
18. October 2007 @ 17:51 |
Link to this message
|
Are you using the 2007 tsop to write to the box?
|
|
Jlewis
Junior Member
|
18. October 2007 @ 17:58 |
Link to this message
|
|
it is eurovoxred tsop modified 03/07/2007
|
AfterDawn Addict
|
18. October 2007 @ 18:03 |
Link to this message
|
|
Post the exact message you are getting in skymax please. Post the exact logfile as appears on skymax screen.
|
|
Jlewis
Junior Member
|
18. October 2007 @ 18:13 |
Link to this message
|
|
Init JTAG
IDCODE : 1D405041
CPU : STi5518
Stop CPU
Clear Trap : Please Wait...
Load Trap -> Ram : Please Wait...
Load Trap : LEN Ok
Init Trap : Please Wait...
Trap_Wptr 80000534
Trap_Iptr 80000140
Start Trap : Please Wait...
Load EMI : Please Wait...
Init OK :)
---------------------
Init JTAG
DCU OK
Trap_Wptr : 80000534
Erase ADR[7FE00000] : Please Wait...
Fail
Init JTAG
DCU OK
Trap_Wptr : 80000534
File : D:\blue eurovox max\eurovoxred tsop.bin
Write Flash ADR[7FE00000] LEN[00200100] : Please Wait...
Error writing flash at address 80002000 ACK = 00000100
Write Flash END
---------------------
|
AfterDawn Addict
|
18. October 2007 @ 18:27 |
Link to this message
|
|
Are you sure it is an ST chip and not an Intel one?
This message has been edited since posting. Last time this message was edited on 18. October 2007 @ 18:27
|
|
Jlewis
Junior Member
|
18. October 2007 @ 18:28 |
Link to this message
|
|
the big chip has st and omega below
|
AfterDawn Addict
|
18. October 2007 @ 18:45 |
Link to this message
|
|
Strange should be fine have you tried jkeys? Is your OS xp or vista?
|
|
Jlewis
Junior Member
|
18. October 2007 @ 18:47 |
Link to this message
|
|
havent tried jkeys dont know what they are. xp professional
|
AfterDawn Addict
|
18. October 2007 @ 20:30 |
Link to this message
|
Try this method using the same tsop file.
Connect JTAG and Power up EuroVox
Start JKEYS
Click on "Development Panel"
Click OK to ingore the warning.
** SEE BELOW IF YOU GET AN ERROR HERE **
If all goes well you will get into the development panel.
In the user functions box:
Type in the address: 80000000
Click on "Load to . . ."
Select the file "unlock_28FxxxC3.bin"
Click "Trigger User"
Close the current window.
Click on "Flash Programming"
Choose the model number as: DXD426RD (1 Chip-GLA)
In the section on the right:
Leave the box above set to "Full"
Click "Erase"
Select YES. This will take a minute to erase.
Click on "Program"
Select YES to "Program at address 0x7FE00000, size 0x200000?"
Choose your TSOP file
Sit and wait for OK to become active, then click it.
Close JKEYS and power the box down.
Disconnect your JTAG
Power the box on. If all has gone well then it should boot up ready for you to rescan for your channels.
*** If you get an error trying to get into the devleopment windows ****
Power the box down and run SkyMax v2.2
Power the box up
Press start.
This seems to reset the box when JKEYS cannot connect (DCU errors).
Close SkyMax and start JKEYS and try again.
Personally I went with Skymax first and then jkeys as it seems to work better.
SkyMax 2
http://www.mediafire.com/?8fzumnj1k9g
Jkeys
http://www.mediafire.com/?e9dyyzgn8q3
|
|
Jlewis
Junior Member
|
21. October 2007 @ 16:07 |
Link to this message
|
|
HI Scouser,
Sorry I couldnt back to you I have been away just got back. Not sure I understand what you mean about jkeys.
JLewis
|
AfterDawn Addict
|
21. October 2007 @ 17:49 |
Link to this message
|
Jkeys will help you flash the tsop to the box it is similar to SkyMax.
|
|
dm500
Suspended permanently
|
22. October 2007 @ 00:36 |
Link to this message
|
|
Thanks for your help, my box is ok now.
|
|
Jlewis
Junior Member
|
22. October 2007 @ 17:54 |
Link to this message
|
|
Hi scouser you around i could use your help
|
AfterDawn Addict
|
22. October 2007 @ 18:56 |
Link to this message
|
|
Scouser is offline at the moment
|
AfterDawn Addict
|
23. October 2007 @ 06:44 |
Link to this message
|
|
Thanks Celt :) just post your query Jlewis and I will see what I can do.
|
|
Jlewis
Junior Member
|
23. October 2007 @ 15:17 |
Link to this message
|
Hi Scouser,
I tried the following:After program never got a yes to to "Program at address 0x7FE00000, size 0x200000? also couldn't see option to choose Tsop. Any ideas
Try this method using the same tsop file.
Connect JTAG and Power up EuroVox
Start JKEYS
Click on "Development Panel"
Click OK to ingore the warning.
** SEE BELOW IF YOU GET AN ERROR HERE **
If all goes well you will get into the development panel.
In the user functions box:
Type in the address: 80000000
Click on "Load to . . ."
Select the file "unlock_28FxxxC3.bin"
Click "Trigger User"
Close the current window.
Click on "Flash Programming"
Choose the model number as: DXD426RD (1 Chip-GLA)
In the section on the right:
Leave the box above set to "Full"
Click "Erase"
Select YES. This will take a minute to erase.
Click on "Program"
Select YES to "Program at address 0x7FE00000, size 0x200000?"
Choose your TSOP file
Sit and wait for OK to become active, then click it.
Close JKEYS and power the box down.
Disconnect your JTAG
Power the box on. If all has gone well then it should boot up ready for you to rescan for your channels.
*** If you get an error trying to get into the devleopment windows ****
Power the box down and run SkyMax v2.2
Power the box up
Press start.
This seems to reset the box when JKEYS cannot connect (DCU errors).
Close SkyMax and start JKEYS and try again.
Personally I went with Skymax first and then jkeys as it seems to work better.
SkyMax 2
http://www.mediafire.com/?8fzumnj1k9g
Jkeys
http://www.mediafire.com/?e9dyyzgn8q3
|
|
Jlewis
Junior Member
|
23. October 2007 @ 15:18 |
Link to this message
|
Hi Scouser,
I tried the following:After program never got a yes to to "Program at address 0x7FE00000, size 0x200000? also couldn't see option to choose Tsop. Any ideas
Try this method using the same tsop file.
Connect JTAG and Power up EuroVox
Start JKEYS
Click on "Development Panel"
Click OK to ingore the warning.
** SEE BELOW IF YOU GET AN ERROR HERE **
If all goes well you will get into the development panel.
In the user functions box:
Type in the address: 80000000
Click on "Load to . . ."
Select the file "unlock_28FxxxC3.bin"
Click "Trigger User"
Close the current window.
Click on "Flash Programming"
Choose the model number as: DXD426RD (1 Chip-GLA)
In the section on the right:
Leave the box above set to "Full"
Click "Erase"
Select YES. This will take a minute to erase.
Click on "Program"
Select YES to "Program at address 0x7FE00000, size 0x200000?"
Choose your TSOP file
Sit and wait for OK to become active, then click it.
Close JKEYS and power the box down.
Disconnect your JTAG
Power the box on. If all has gone well then it should boot up ready for you to rescan for your channels.
*** If you get an error trying to get into the devleopment windows ****
Power the box down and run SkyMax v2.2
Power the box up
Press start.
This seems to reset the box when JKEYS cannot connect (DCU errors).
Close SkyMax and start JKEYS and try again.
Personally I went with Skymax first and then jkeys as it seems to work better.
SkyMax 2
http://www.mediafire.com/?8fzumnj1k9g
Jkeys
http://www.mediafire.com/?e9dyyzgn8q3
|
|
Jlewis
Junior Member
|
23. October 2007 @ 15:21 |
Link to this message
|
Hi Scouser,
I tried the following:After program never got a yes to to "Program at address 0x7FE00000, size 0x200000? also couldn't see option to choose Tsop. Any ideas
Try this method using the same tsop file.
Connect JTAG and Power up EuroVox
Start JKEYS
Click on "Development Panel"
Click OK to ingore the warning.
** SEE BELOW IF YOU GET AN ERROR HERE **
If all goes well you will get into the development panel.
In the user functions box:
Type in the address: 80000000
Click on "Load to . . ."
Select the file "unlock_28FxxxC3.bin"
Click "Trigger User"
Close the current window.
Click on "Flash Programming"
Choose the model number as: DXD426RD (1 Chip-GLA)
In the section on the right:
Leave the box above set to "Full"
Click "Erase"
Select YES. This will take a minute to erase.
Click on "Program"
Select YES to "Program at address 0x7FE00000, size 0x200000?"
Choose your TSOP file
Sit and wait for OK to become active, then click it.
Close JKEYS and power the box down.
Disconnect your JTAG
Power the box on. If all has gone well then it should boot up ready for you to rescan for your channels.
*** If you get an error trying to get into the devleopment windows ****
Power the box down and run SkyMax v2.2
Power the box up
Press start.
This seems to reset the box when JKEYS cannot connect (DCU errors).
Close SkyMax and start JKEYS and try again.
Personally I went with Skymax first and then jkeys as it seems to work better.
SkyMax 2
http://www.mediafire.com/?8fzumnj1k9g
Jkeys
http://www.mediafire.com/?e9dyyzgn8q3
|
|
Jlewis
Junior Member
|
23. October 2007 @ 15:27 |
Link to this message
|
Hi Scouser,
I tried the following:After program never got a yes to to "Program at address 0x7FE00000, size 0x200000? also couldn't see option to choose Tsop. Any ideas
Try this method using the same tsop file.
Connect JTAG and Power up EuroVox
Start JKEYS
Click on "Development Panel"
Click OK to ingore the warning.
** SEE BELOW IF YOU GET AN ERROR HERE **
If all goes well you will get into the development panel.
In the user functions box:
Type in the address: 80000000
Click on "Load to . . ."
Select the file "unlock_28FxxxC3.bin"
Click "Trigger User"
Close the current window.
Click on "Flash Programming"
Choose the model number as: DXD426RD (1 Chip-GLA)
In the section on the right:
Leave the box above set to "Full"
Click "Erase"
Select YES. This will take a minute to erase.
Click on "Program"
Select YES to "Program at address 0x7FE00000, size 0x200000?"
Choose your TSOP file
Sit and wait for OK to become active, then click it.
Close JKEYS and power the box down.
Disconnect your JTAG
Power the box on. If all has gone well then it should boot up ready for you to rescan for your channels.
*** If you get an error trying to get into the devleopment windows ****
Power the box down and run SkyMax v2.2
Power the box up
Press start.
This seems to reset the box when JKEYS cannot connect (DCU errors).
Close SkyMax and start JKEYS and try again.
Personally I went with Skymax first and then jkeys as it seems to work better.
SkyMax 2
http://www.mediafire.com/?8fzumnj1k9g
Jkeys
http://www.mediafire.com/?e9dyyzgn8q3
|
|
Advertisement
|
|
|
|
Jlewis
Junior Member
|
23. October 2007 @ 15:30 |
Link to this message
|
Hi Scouser,
I tried the following:After program never got a yes to to "Program at address 0x7FE00000, size 0x200000? also couldn't see option to choose Tsop. Any ideas
Try this method using the same tsop file.
Connect JTAG and Power up EuroVox
Start JKEYS
Click on "Development Panel"
Click OK to ingore the warning.
** SEE BELOW IF YOU GET AN ERROR HERE **
If all goes well you will get into the development panel.
In the user functions box:
Type in the address: 80000000
Click on "Load to . . ."
Select the file "unlock_28FxxxC3.bin"
Click "Trigger User"
Close the current window.
Click on "Flash Programming"
Choose the model number as: DXD426RD (1 Chip-GLA)
In the section on the right:
Leave the box above set to "Full"
Click "Erase"
Select YES. This will take a minute to erase.
Click on "Program"
Select YES to "Program at address 0x7FE00000, size 0x200000?"
Choose your TSOP file
Sit and wait for OK to become active, then click it.
Close JKEYS and power the box down.
Disconnect your JTAG
Power the box on. If all has gone well then it should boot up ready for you to rescan for your channels.
*** If you get an error trying to get into the devleopment windows ****
Power the box down and run SkyMax v2.2
Power the box up
Press start.
This seems to reset the box when JKEYS cannot connect (DCU errors).
Close SkyMax and start JKEYS and try again.
Personally I went with Skymax first and then jkeys as it seems to work better.
SkyMax 2
http://www.mediafire.com/?8fzumnj1k9g
Jkeys
http://www.mediafire.com/?e9dyyzgn8q3
|
