|
trouble flashing benq
|
|
Senior Member
|
24. July 2008 @ 17:51 |
Link to this message
|
|
Hi all, i have been stuck at this point for days now where i have made my iprep flash drive, loaded it up from dos and got to the part where it says MTK VENDOR intro failure. press y to send, i press y and it is supposed read the 4 banks to backup the orig.bin file but it doest change from 0x7F. I have a via 6421 sata and no raid is installed. Am really pulling my hair out here and havent got much left.lol. Could someone please help. Thanks
|
|
Advertisement
|
|
|
|
AfterDawn Addict
|
24. July 2008 @ 19:30 |
Link to this message
|
make sure that you have the 360 plugged into the channel one of your pci card. i would bet that this is the issue. channel one is the sata slot closest to the front of the pc case.
|
|
gregy21a
Newbie
|
25. July 2008 @ 00:01 |
Link to this message
|
I had this problem..I was running a high spec pc with vista and an extra sata card..
same problem as you, couldnt write no matter what.
so i got an old pc, setup xp on it, with my sata card.
Burned the benq no problems..
|
Senior Member
|
25. July 2008 @ 02:00 |
Link to this message
|
|
I have 3 pci slots on top of each other, would slot 1 be the highest because thats the one i have it plugged into, and my pc is about 3 years old running xp?
|
AfterDawn Addict
4 product reviews
|
25. July 2008 @ 06:27 |
Link to this message
|
|
if one dosnt work do the other. mine was the same way (up/down)i put mine in the top pci. closest to the top of the pc.
|
|
Jose30330
Suspended permanently
|
25. July 2008 @ 07:16 |
Link to this message
|
Originally posted by homesick:
if one dosnt work do the other. mine was the same way (up/down)i put mine in the top pci. closest to the top of the pc.
No one cares what you think, you *bleep*. Why don't you *bleep* while you *bleep*. LOL no wonder Creaky hates you as much as me, you are so *bleep* and ALWAYS post here.
This message has been edited since posting. Last time this message was edited on 25. July 2008 @ 12:02
|
|
Torry46
Member
|
25. July 2008 @ 10:00 |
Link to this message
|
|
had same problem mate, make sure your sata cable is connect to the slot a the end of the PCI card inside the computer, it wont work from any other sata slot on the card...only the one on the end
Torry
|
Senior Member
|
25. July 2008 @ 11:55 |
Link to this message
|
|
Tory , i have tried that port, still nothing. I have moved it up and down but nothing. My sata card works fine with my dl writer which is what i use it for when not flashing!
|
Moderator
|
25. July 2008 @ 12:04 |
Link to this message
|
Originally posted by Jose30330:
Originally posted by homesick:
if one dosnt work do the other. mine was the same way (up/down)i put mine in the top pci. closest to the top of the pc.
No one cares what you think, you *bleep*. Why don't you *bleep* while you *bleep*. LOL no wonder Creaky hates you as much as me, you are so *bleep* and ALWAYS post here.
You are ignorant, foul mouthed, bang out of order, abusive, oh and you have a downright nerve to even think you know what i think, never mind to have the cheek to speak for me. I don't 'hate' anybody, my comments to homesick or anyone else are never personal.
You are excused. Make sure to bang your head on the way out.
Main PC ~ Intel C2Q Q6600 (G0 Stepping)/Gigabyte GA-EP45-DS3/2GB Crucial Ballistix PC2-8500/Zalman CNPS9700/Antec 900/Corsair HX 620W
Network ~ DD-WRT ~ 2node WDS-WPA2/AES ~ Buffalo WHR-G54S. 3node WPA2/AES ~ WRT54GS v6 (inc. WEP BSSID), WRT54G v2, WRT54G2 v1. *** Forum Rules *** |
|
NasirJns
Suspended due to non-functional email address
|
25. July 2008 @ 14:20 |
Link to this message
|
|
You could also change the serial cable...I know your burner works but its worth a try. The same exact thing happen to me.
|
Senior Member
|
25. July 2008 @ 14:57 |
Link to this message
|
|
yeh thought about that mate, but it wasnt a cheapy from ebay so didnt think it would be the problem!
|
|
cvsre140
Newbie
|
25. July 2008 @ 17:46 |
Link to this message
|
I realise this may be an obvious thing to say but you are swiching the 360 on and off for a few seconds aren't you?
I only ask as i did a benq drive yesterday and it does get stuck on 0x7F but you have to switch the 360 off for a few seconds and then switch it on again.
|
Senior Member
|
25. July 2008 @ 18:09 |
Link to this message
|
The tut that i followed said that i dont switch it on until i have pressed y and then the status 0x7F comes up, after 2 seconds it is supposed to start flickering between d1 and something else, then you turn it off for 2 secs and back on and it reads banks but it doesnt change from 0x7F
|
|
gregy21a
Newbie
|
25. July 2008 @ 20:08 |
Link to this message
|
you're just spinning your wheels here dude... as I said I had the exact same problem... it was as if the computer or add on sata controller would not recognise the benq drive so I couldnt do a dump..same as you.
|
Senior Member
|
26. July 2008 @ 05:00 |
Link to this message
|
|
Ok thanks guys for your help
|
|
bigpapa09
Newbie
|
26. July 2008 @ 20:22 |
Link to this message
|
|
if i were you i would reinstall the drivers( i think the one's you want are like 5.20 or something like that)
|
Senior Member
|
27. July 2008 @ 11:35 |
Link to this message
|
|
Where can i get that driver from mate, MY card installed through windows wizard thing, dont know if they were the right ones?
This message has been edited since posting. Last time this message was edited on 27. July 2008 @ 11:36
|
AfterDawn Addict
|
27. July 2008 @ 12:07 |
Link to this message
|
@bigPapa09
Quote:
if i were you i would reinstall the drivers( i think the one's you want are like 5.20 or something like that)
If you're not sure what driver to tell him to install don't bother posting and maybe making his problem worse.
|
|
bigpapa09
Newbie
|
27. July 2008 @ 14:53 |
Link to this message
|
|
|
AfterDawn Addict
|
27. July 2008 @ 14:53 |
Link to this message
|
Originally posted by sn0wman1:
Where can i get that driver from mate, MY card installed through windows wizard thing, dont know if they were the right ones?
you can get the driver from the manufacturers website.
|
Senior Member
|
27. July 2008 @ 15:45 |
Link to this message
|
|
Thanks guys, dont argue on my account. Will give it ago tomorrow. Had a drink now, Thanks..
|
Senior Member
|
28. July 2008 @ 13:03 |
Link to this message
|
Sorry to sound like a noob but i have downloaded that driver pack but have not got a clue what to install, i thought i did not want anything raid? Any ideas which i install please!
|
|
bigpapa09
Newbie
|
28. July 2008 @ 23:02 |
Link to this message
|
|
it should automatically find your card and when it asks you to install, go to the drivers and select that, and make sure u dont download the RAID.
|
Senior Member
|
30. July 2008 @ 03:50 |
Link to this message
|
|
I have tried updating drivers, changing my pci slots, changing ports on my pci card, still nothing. I GIVE UP. lol. Thanks everyone...
|
|
Advertisement
|
|
|
|
grimsby49
Account closed as per user's own request
|
1. August 2008 @ 09:45 |
Link to this message
|
I had the same problem in the waiting 2 second trick with my Benq Drive and the pci card 6421. It didn't work, whether I counted 2 seconds or had a timer.
Eventually, it worked after pressing yes, then turned it off/on very quickly.
I have both backed up my original bin and flashed the custom firmware and am able to play back up's with no problems.
Maybe it's the version of benq that I'm using. Mine was manufactured in November 2007. Try the quick on/off suggestion as I did. Hope it works for you.
|
