|
Digivox-T
|
|
|
kevcle
Newbie
|
5. February 2009 @ 06:08 |
Link to this message
|
Originally posted by cactikid:
if u read the handbooku have to switch antennae power on,
i have same version of firmware as redrebel v03-3.0000t.coax in antenna. scart in tv on digivox.latest codes in. antenna power on. key emu on. still the same. no signal. 0 program found after autoscan or manual scan at 508 mhz
|
|
Advertisement
|
 |
|
|
|
redrebel
Newbie
|
5. February 2009 @ 12:31 |
Link to this message
|
Kevcle, Did the supplier of your new STB confirm that this was a direct replacement for the Eurovox TX and would work in your area?
|
|
cwkk
Newbie
|
5. February 2009 @ 13:08 |
Link to this message
|
Originally posted by kevcle:
Originally posted by cwkk:
hi kevcle,
did you get digivox to work in kilkenny? and how?
hi cwkk ,no luck. cactikid reckons digivox t isnt suitable for mmds through a communal cable feed. only suitable for mmds from aerial on roof. still not sure of this or which box exactly is suitable. saw your earlier posts did you have any luck with your digivox t.
hi kevcle, no luck yet, i'm following you guys.best of luck with it.
|
|
fergusrb
Suspended permanently
|
5. February 2009 @ 13:14 |
Link to this message
|
|
Try a manuall scan on the box and see what you get try a freq like 250.000 and move up in increments of 8mhz and see do you get anything
also make sure the cable is in the ANT input on the top right looking from the front of the box
also make sure you enable the ant power before doing any scan
|
|
redrebel
Newbie
|
5. February 2009 @ 13:55 |
Link to this message
|
|
Hi Fergusrb. Thanks for your support. Tried suggestion, observing all your search criteria, still no luck. Keep seeing "No signal" Cannot understand this as the signal is there when accessing service providers TV schedule
|
|
fergusrb
Suspended permanently
|
5. February 2009 @ 14:01 |
Link to this message
|
|
what box have you got from the provider can you tell me
SAGAM ????
if so look under box and see if you can see the letters ITD anywhere on the box
|
|
redrebel
Newbie
|
5. February 2009 @ 14:11 |
Link to this message
|
|
|
|
fergusrb
Suspended permanently
|
5. February 2009 @ 14:15 |
Link to this message
|
|
yep your defo on MMDS so
you will need to go to the lowest freq and move up in 8mhz at a time to try and find some channel once you find one you will find the rest trial and error thats all i can say
try both of the ANT inputs on the box as there are 2 on that box
|
|
redrebel
Newbie
|
5. February 2009 @ 14:21 |
Link to this message
|
|
Thanks. Will have another go and report back
|
|
redrebel
Newbie
|
5. February 2009 @ 18:18 |
Link to this message
|
|
Hi Fergusrb, Back again. Tried both input connections in increments of 8 MHz. No success. On manual scan noticed that the channel number on the top line of the manual scan menu(Channel Numbers 4-15)kept disappearing once I entered numbers outside those assigned i.e. Selected Channel 4, 218.000 MHz assigned to this channel, once I incremented this up by 8 channel number read CH---. Is this OK?
|
|
redrebel
Newbie
|
6. February 2009 @ 06:14 |
Link to this message
|
|
Kevcle / Cwkk, Any progress on your front?
|
|
mgb17
Senior Member
|
6. February 2009 @ 06:50 |
Link to this message
|
|
Try a manual scan via 506, 514, 522, 530, 538 mhz and so on for Kilkenny.
|
|
redrebel
Newbie
|
6. February 2009 @ 13:27 |
Link to this message
|
Will do
Got a response from the supplier and they asked if anyone in the Kilkenny area could provide information on at least one frequency from an existing working Eurovox TX stb. His suggestion is that once this is known then those experiencing the "No signal" "No channels found" should add it to a manual scan and see what happens.
|
|
kevcle
Newbie
|
6. February 2009 @ 15:48 |
Link to this message
|
|
hi cwkk and redrebel. sorry for slow reply, working. my supplier sent me digivoxt as direct replacemnt for failed eurovoxtx. no luck as yet with manual scan. will let you know of any progress.thanks for your help fergusrb.
|
Member
|
6. February 2009 @ 17:01 |
Link to this message
|
|
hi guys.dont want to sound silly but is it possible that your supplier could have changed from terrestrial mmds to cable mmds without changing their own box
jvob
|
|
redrebel
Newbie
|
7. February 2009 @ 16:38 |
Link to this message
|
|
Away at the moment. Will report on any progress as it happens
|
|
kevcle
Newbie
|
8. February 2009 @ 08:41 |
Link to this message
|
hi everyone. made some progress today.put coax cable feed in antenna(top corner of box)with v03-3.0000t firmware installed,turned antenna power to on and then done a manual scan starting with 506mhz,then514,522,530,538,546,554,562,570,578,586,594,602,618,626 and finally 634mhz as mgb17 said earlier in thread.now i have a couple of good channels but mostly scrambled or bad channel comes up.might have to do channel dump. let you know how i get on.
|
AfterDawn Addict
|
8. February 2009 @ 08:54 |
Link to this message
|
after u get channels u need to put emu on,menu-system info1004.emu to on and exit out.
|
|
kevcle
Newbie
|
8. February 2009 @ 09:20 |
Link to this message
|
|
cactikid your a genius!thanks very much. have all channels now. just no channel names but thats no problem.hope you get all that cwkk and redrebel. if you have any questions ill try to help but one thing is for sure, digivoxt will work with communal mmds feed.
|
|
cwkk
Newbie
|
9. February 2009 @ 16:48 |
Link to this message
|
|
hi kevcle, well done, tried a manual scan, unable to get beyond 378mhz, must be doing something wrong again.will keep trying. thanks for all the help, to you and the others.
|
|
kevcle
Newbie
|
9. February 2009 @ 19:34 |
Link to this message
|
i had box powered off for a good while[overnight], firmware pre loaded [v03.30000t],coax in antenna not antenna in,put antenna power on, then went to manual scan starting with 506 mhz,wait for signal level and quality percentages to rise at bottom of screen[somewhere between 70 or 80%, only then ok.continue this right thru other values stated above and then after some channels found go sys info,1004,key emu to on, then all channels should be there.as some seniors said above its trial and error.keep trying ,best of luck.
|
|
cwkk
Newbie
|
10. February 2009 @ 03:23 |
Link to this message
|
|
done all you said exactly and it worked. im delighted. thanks a mil to you and the rest especially cactikid
|
|
sallmount
Suspended due to non-functional email address
|
10. February 2009 @ 12:20 |
Link to this message
|
hi guys, just a quick question. can sv 4 firmware be changed over to starview mmds firmware, i.e. useing the stb for dvb-t rather than dvb-c. thanks
|
AfterDawn Addict
|
10. February 2009 @ 15:17 |
Link to this message
|
Originally posted by sallmount:
hi guys, just a quick question. can sv 4 firmware be changed over to starview mmds firmware, i.e. useing the stb for dvb-t rather than dvb-c. thanks
firmware is made for 1 box only it is not universal,dvb/t firmware is different than dvb/c so do not use it,correct box needed for correct signal.
|
|
Advertisement
|
|
|
|
sallmount
Suspended due to non-functional email address
|
10. February 2009 @ 15:31 |
Link to this message
|
|
ok thanks a lot
|
