|
PS3 RSX chip came off the motherboard
|
|
Senior Member
1 product review
|
21. November 2009 @ 13:39 |
Link to this message
|
|
Assemble it now. Dont let it dry seperatly.
|
|
Advertisement
|
|
|
|
|
ne4ious
Newbie
|
8. December 2009 @ 14:29 |
Link to this message
|
Originally posted by SalTru89:
I followed everyone's instructions and my PS3 now works good as new.
Many thanks to the following:
canuckerz
ebega
glassd
ibizagti
KillerzBug
matt6247
NinReznor
TaZMaNiaK
And as for canuckerz question, It's about the same for now but if anything changes I'll let you know.
Thanks again everyone.
ne4ious-
|
|
ne4ious
Newbie
|
8. December 2009 @ 14:33 |
Link to this message
|
posted a blank post, posting blanks i guess. :)
SALTRU, dude, how long did you let the Thermal Epoxy cure before you put your PS3 back together?
ne4ious-
|
|
sky920
Member
|
8. December 2009 @ 14:43 |
Link to this message
|
|
damn dude this thread is old, why did u post in it?
|
Senior Member
1 product review
|
8. December 2009 @ 15:20 |
Link to this message
|
Because I refered him to it the other day. It is a good thread that can collect good information. It will be a good thread to keep alive.
ne4ious, We assemble our SCR's etc Immediately. The heat will cure it.
This message has been edited since posting. Last time this message was edited on 8. December 2009 @ 15:23
|
|
ne4ious
Newbie
|
8. December 2009 @ 17:08 |
Link to this message
|
Thanks Glassd, but i will let my Epoxy cure for at least 4 hours, am afraid the epoxy might not be hard enough and thus run off the sides. it is a bit chilly inside the house and think that might delay my cure time.
this is a very helpful post to keep alive. am sure many ppl will have this problem as they continue to reflow their PS3's more often.
what i do now on PS3's when Heat-Spreader is locked on to the Heat-Pad on the Cooling Fan is that i start to heat the PS3 mobo from the back side where the fan is located, do not heat for a long time, just enough to get the Thermal Paste gooey are able to seperate the Heat-Pads from each other.
ne4ious-
|
|
sky920
Member
|
8. December 2009 @ 19:11 |
Link to this message
|
Originally posted by glassd:
Because I refered him to it the other day. It is a good thread that can collect good information. It will be a good thread to keep alive.
ne4ious, We assemble our SCR's etc Immediately. The heat will cure it.
ah, just curious...
|
AfterDawn Addict
1 product review
|
14. December 2009 @ 02:43 |
Link to this message
|
Originally posted by glassd:
Because I refered him to it the other day. It is a good thread that can collect good information. It will be a good thread to keep alive.
ne4ious, We assemble our SCR's etc Immediately. The heat will cure it.
This is a great thread; the YLOD-heatgun-fix thread should like to this thread and say something like, "before you try the dangerous heatgun fix, try the harmless glue fix"
|
|
imanewguy
Member
|
14. December 2009 @ 04:40 |
Link to this message
|
Does the ps3 really turn back on as if nothing had happened? Or does it make you reformat or ask you to create a user as if it were new?
This message has been edited since posting. Last time this message was edited on 14. December 2009 @ 04:40
|
|
Advertisement
|
|
|
Senior Member
1 product review
|
14. December 2009 @ 09:22 |
Link to this message
|
I would assume that if the HD has not been replaced and nothing happened to the E-prom/Flash, all would be normal.
|
