|
First Ever Bricked 360!
|
|
|
ThyFonz
Junior Member
|
29. January 2010 @ 20:45 |
Link to this message
|
Well I bricked my first 360 ever...
Cygnos + plus RROD = Fully bricked 360....
So I finally was figuring out how to get frestyle dash xexloader and all that going was on the furge of tetsin out XeXloader, When bang Screen freeze, restart back into RROD, Damn man, so i reflow the board by putting it into my toaster oven at 185 F, put it back together starts up fine... Ok turn cynos on and nothing huh..... alright back off... turns on fine.... ok maybe the nand flash got screwed, tryed orig nand on cygnos worked fine, tryed *********-nand got E79.... Mmmmmm really wierd after i had it just working.... 360 RRod's again.... once again i fix it do a quick cheap reflow...... got it going again this time, alot of invalid blocks while reading the cygnos nand, non while reading 360 nand... so i figured a simple reprogramming would fix the invalid block on the cygnos (had to use toolbox 1.05 with ignore invalid blocks) After this everything i try and read the 360 nand or cygnos nand or program the cygnos nand it says please check install, and to top it off the 360 doesn't even turn anymore no matter which setting the cygnos switch is set to... OMG jjeeeeeze, im gonna go with the JTAG LTP on my next box... rediculous.... Think maybe i could rewrite the 360 nand using the LTP trick? I already got many proper nands already for this mobo
Ehhhhh!
|
|
Advertisement
|
 |
|
|
AfterDawn Addict
|
29. January 2010 @ 23:53 |
Link to this message
|
Originally posted by ThyFonz:
Think maybe i could rewrite the 360 nand using the LTP trick?
That's the first thing I'd do. Actually, the first thing I'd do after installing the lpt is dump the nand and compare it to the other dumps.
|
|
ThyFonz
Junior Member
|
30. January 2010 @ 01:40 |
Link to this message
|
|
I will do that but i doubt the existing nand on there is any good considering it wont turn on anymore, i think while toolbox was flashing the cygnos nand it was rewritting the 360 nand as well... im almost done the setup and will update status tomorrow let ya guys know
Ehhhhh!
|
|
ThyFonz
Junior Member
|
30. January 2010 @ 02:54 |
Link to this message
|
|
Well not looking good so far maybe my shitty (just pluging into the lpt port instead of usuing a proper adatper, check again but it was gettin the properer flasgconfig Id, same with lpt address and start and ending address, but error reading every block, and while attempting to write old nand back on also gettin error programming everyblock, It's completly briocked as far as im thinkin i can do anything
Ehhhhh!
|
|
jpizzle
Senior Member
|
30. January 2010 @ 03:58 |
Link to this message
|
|
|
ThyFonz
Junior Member
|
30. January 2010 @ 10:30 |
Link to this message
|
|
lol well im still waiting fo rit to complete wrting first even though it says error, it still seems to be writing or something cause it changes when anone on of the lpt pins come out, and it wont detect anytihng until i reinsert which ever fell out, if that fails i will try that pin shorting, thx for the heads up man!
Ehhhhh!
|
|
jpizzle
Senior Member
|
30. January 2010 @ 12:09 |
Link to this message
|
|
anytime bro
|
AfterDawn Addict
|
30. January 2010 @ 13:39 |
Link to this message
|
Originally posted by ThyFonz:
i doubt the existing nand on there is any good considering it wont turn on anymore
That's why I'd dump it first and compare them. If it did happen to be good then you'd know your rrod was some other hardware issue.
But if you're already trying to write now then it's too late to check. If you're getting errors, change your lpt port to epp in your pc bios.
|
|
ThyFonz
Junior Member
|
30. January 2010 @ 20:54 |
Link to this message
|
|
Thx for the heads up i changed to epp in bois, and still gettin the same error code, i revamped all my lpt connections so i know they are flawless. when i try to eitherr read write or erase any block it posts
"Error:8001 reading block 1"
replaceing reading with writing or erasing all give me the same thing, I tryed the Nand pin sort rtick didn't seem to do anyting no matter how man times i ran the wire across the pins. And im still gettin the corret flash config start and end blocks, just cant read or write.... I was so hoiping for the nand pin shotr to save my bacon, might have to sell as is, unless any other ideas come up... thanks for all those who came up with some ideas
Ehhhhh!
|
AfterDawn Addict
|
30. January 2010 @ 23:41 |
Link to this message
|
|
Any chance of posting a pic of your solder connections?
|
|
ThyFonz
Junior Member
|
31. January 2010 @ 06:11 |
Link to this message
|
|
I will post pics of my onboard solder job, which i know is good, just been doing precision soldering for a while, cant do any micro soldering but then again i am using a 30 watt 10 dollar iron from the source, but it work great for all my solder jobs so far. Will post when i borrow i camera that cam focus on close up shots... still willing to take ideas even if it puts my work to shame lol... no is perfect not even me by far. But yeah after dawn guys are great at least you 2 that are replying lmao thanks again guys, post pics tomorrow
Ehhhhh!
|
|
Advertisement
|
|
|
AfterDawn Addict
|
31. January 2010 @ 10:39 |
Link to this message
|
Originally posted by ThyFonz:
still willing to take ideas even if it puts my work to shame lol... no is perfect not even me by far.
This isn't a beauty contest. We're not here to judge how good it looks. Just how functional. Just trying to cover all the bases.
|
