|
Flash a Lite-On DG-16D2S (74850C) Xbox 360
|
|
|
quidum
Newbie
|
12. October 2010 @ 18:09 |
Link to this message
|
Hi there,
I am looking for some help flashing this drive?
I have the ck3 pro and probe v2 I have it all set up right but when I try to get the key it comes back
Drive is Lite-On.. Sending DVDKey request to I/O port 0xFF00 and COM3
................ Serial Data is bad,
DVDkey files extraction aborted!
Can anyone help me??
Oh i am using usb as seral cable not get picked up for some reason.
This message has been edited since posting. Last time this message was edited on 12. October 2010 @ 18:10
|
|
Advertisement
|
|
|
|
|
quidum
Newbie
|
12. October 2010 @ 18:26 |
Link to this message
|
the probe lights up amb for standby and green then when im ready to extract the dvd key and press the top button both lights go out? if that make and sence? the green light is ment to stay on - I have chhecked out the settings on the probe and they are right? is there some thing i am missing??
|
AfterDawn Addict
|
12. October 2010 @ 18:40 |
Link to this message
|
|
Have you cut the traces and soldered the jumper on the drive yet?
|
|
quidum
Newbie
|
12. October 2010 @ 18:50 |
Link to this message
|
Originally posted by eebeejay:
Have you cut the traces and soldered the jumper on the drive yet?
no the guides i have been following say you dont neet to solder or any fin
|
|
quidum
Newbie
|
12. October 2010 @ 19:04 |
Link to this message
|
this is one of the guides i have seen
http://www.team-xecuter.com/video/liteon/74850/
keep getting
Drive is Lite-On.. Sending DVDKey request to I/O port 0xFF00 and COM3
................ Serial Data is bad,
DVDkey files extraction aborted!
can any one help?????
This message has been edited since posting. Last time this message was edited on 12. October 2010 @ 19:06
|
AfterDawn Addict
|
12. October 2010 @ 22:01 |
Link to this message
|
|
Senior Member
|
13. October 2010 @ 04:22 |
Link to this message
|
|
are u puttin the probe in the rite hole?
|
|
Modking30
AfterDawn Addict
|
13. October 2010 @ 11:21 |
Link to this message
|
|
Well the probe 2 isn't even the right probe for the 707 method anyway. You need the probe one. Yes you need to solder and cut traces if you want to dump the firmare properly. Full dump, dumps the laser calibration that will keep the life of your laser.
|
|
quidum
Newbie
|
13. October 2010 @ 12:48 |
Link to this message
|
Originally posted by infam0us:
are u puttin the probe in the rite hole?
yeah lights green and amb then press button on top both lights go out.
|
|
quidum
Newbie
|
13. October 2010 @ 13:29 |
Link to this message
|
this states you dont need to do that.
No Solder Add-on!!
After the amazing success of the Xecuter LT Switch solution for Liteon drives, Team Xecuter have launched the latest addition to their CK3 family of products ? the FIRST complete NO SOLDER* solution for the new version Liteon DVD drives ? the CK3 Probe v2.
This is targeted to installers who require a multi-use no solder* solution to the new Liteon drives ? or to the users who simply don?t have the skills to solder the cheaper Xecuter LT Switch alternative.
Still retaining the original CK3 Probe function of dumping the 74850 key (the only product to date to have both original Probe v1 and Probe v2 LT Switch functions in the same device), but now also enabling full firmware access of the new 83850V2 and 93450 drives ? you can easily switch between PROBE and LT Switch Modes.
A complete all-in-one solderless* solution! Installers can use this again and again and again and again ? No rebuild boards ? No soldering* ? NO PROBLEM!
The CK3 Probe 2 connects to both the CK3 Lite and CK3 Pro connectivity kits and includes full status LED?s and an extra protection circuit against accidental shortages on the DVD PCB.
Feature list:
The First No-Solder Solution For ALL Liteon Drives including no trace cut for Liteon 74850!
Original CK3 Probe Function (Liteon 74850 DVD Key) - No Trace Cutting !
New No-Solder LT Switch Probes (Liteon 83850V2 & Liteon 93450) - Small PCB Trace Cuts - Repaired With Special Conductive Glue
New ©MULTI-R Feature !
Improved Liteon Winbond Chipset Support
Power / Status / Standby LED's
New Protection Circuit To Protect Against Accidental Shortages (LED Permanent On Syndrome)
Fits to CK3 Lite and CK3 Pro
GameStuff.ca Guides Section:
CK3 Probe II Tutorial - PROBE V1 MODE (Liteon 74850)
|
|
polk68
Newbie
|
13. October 2010 @ 14:01 |
Link to this message
|
|
go on youtube, and do a search for mwest23. His guide will show you how to setup the probe, and how to extract the dvdkey.
|
|
Modking30
AfterDawn Addict
|
13. October 2010 @ 14:16 |
Link to this message
|
|
So you bought the LT switch?
|
|
quidum
Newbie
|
13. October 2010 @ 14:25 |
Link to this message
|
sorry what is LT switch??
i have the The CK3 Probe 2 thats it
This message has been edited since posting. Last time this message was edited on 13. October 2010 @ 14:28
|
Senior Member
|
13. October 2010 @ 14:32 |
Link to this message
|
|
Check on your probe, there is a switch, make sure its set to PROBE and not MRA, then try and dump again!!
|
|
Modking30
AfterDawn Addict
|
13. October 2010 @ 14:32 |
Link to this message
|
Originally posted by quidum:
sorry what is LT switch??
i have the The CK3 Probe 2 thats it
LMAO!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
Dude, you just quoted a guide. That guide is the the ADD ON as stated above which is the LT switch. You still have to make 2 CUTS, and use the messy glue.
|
|
quidum
Newbie
|
13. October 2010 @ 14:40 |
Link to this message
|
Originally posted by sn0wman1:
Check on your probe, there is a switch, make sure its set to PROBE and not MRA, then try and dump again!!
all settings are right on the probe still not working
|
|
Modking30
AfterDawn Addict
|
13. October 2010 @ 15:36 |
Link to this message
|
Originally posted by quidum:
Originally posted by sn0wman1:
Check on your probe, there is a switch, make sure its set to PROBE and not MRA, then try and dump again!!
all settings are right on the probe still not working
Did you MAKE THE CUTS?
|
|
quidum
Newbie
|
13. October 2010 @ 15:59 |
Link to this message
|
|
no how do I do that?? is there a video or guide about?
This message has been edited since posting. Last time this message was edited on 13. October 2010 @ 15:59
|
|
Advertisement
|
|
|
|
Modking30
AfterDawn Addict
|
13. October 2010 @ 16:15 |
Link to this message
|
Originally posted by quidum:
no how do I do that?? is there a video or guide about?
You should really research. You keep making posts saying it's not working, when we've gave you the answers. There are like 5 other threads dicussing this
|
