|
Dbox In Ireland
|
|
|
srevor
Junior Member
|
19. June 2007 @ 10:49 |
Link to this message
|
Originally posted by mgb17:
You have to reboot the box after a ucode change and if you don't know how pull the plug.
yeah, cheers. I already rebooted it after changing the codes, but some channels are still choppy. I'm too wrecked after 2 days of messing around with it to go and mess it all up again.
|
|
Advertisement
|
|
|
|
|
mgb17
Senior Member
|
19. June 2007 @ 11:03 |
Link to this message
|
|
Check the boot options in the dbox button menue.
Hardware section should be switched off, Avia watchdog and enx watchdog to on.
If you change settings reboot the box.
|
|
srevor
Junior Member
|
19. June 2007 @ 11:32 |
Link to this message
|
Originally posted by mgb17:
Check the boot options in the dbox button menue.
Hardware section should be switched off, Avia watchdog and enx watchdog to on.
If you change settings reboot the box.
Cheers, i checked that. hardware was off, avia watchdog was on, but enx watchdog was off. i turned it on and rebooted, some channels are still choppy, some are perfect. I'm happy enough with that for now. Thanks a million for all your help guys. I might pick your brains later about those choppy/freezing channels. Now, im going to sit down with a drink and watch some free TV!
This message has been edited since posting. Last time this message was edited on 19. June 2007 @ 12:34
|
|
ruprect
Senior Member
|
20. June 2007 @ 00:03 |
Link to this message
|
I but blade on my mates sagem 1x last night. Started chirping after a few mins. I then put on JTG (meant to be suited to chirping sagems), this appears to only have ucode 0014, and I cannot see any place in it to change ucodes or EMU's, however it was working with no chirps. But I was only watching for 15mins tops.
Originally posted by mgb17:
Hardware section should be switched off, Avia watchdog and enx watchdog to on.
I noticed this was the setup on JTG, I thought avia was a Nokia setting so usually have it off. I will change it on my others.
On digitalworldz you said
Quote:
If its a sagem enable the enx check in cwshare.cfg and restart the emu.
N: { 00 01 03 00 3500 6000 }
I did this but it is still freezing but self recovering, but it still freezes on a FTA channel too.
In the file it says
Quote:
# 3500 send ecm again after 3,5 Seconds if no reply
# 6000 resync decode after 6 Seconds if net decode failed
Could I change 3500 to 1200 to check every 1,2seconds? would this decrease the freezing time?
Are there other settings/files I could adjust? I see other files with other encryption types mentioned, does the box waste time looking for these while it should be only looking for nagra? i.e. would deleting other generic settings help make it a faster nagra specific box?
This message has been edited since posting. Last time this message was edited on 20. June 2007 @ 00:13
|
|
mgb17
Senior Member
|
20. June 2007 @ 06:34 |
Link to this message
|
|
The 2 numbers are for card sharing.
If the enx chip crash and need a reset you simple get a short freeze.
You could try ucode version 001A at the JtG image.
The ucode.bin is the firmware for the enx chip and is loaded into that chip at bootup.
This message has been edited since posting. Last time this message was edited on 20. June 2007 @ 06:38
|
|
srevor
Junior Member
|
20. June 2007 @ 09:24 |
Link to this message
|
|
Back again!
heres my story so far:
got a sagem 2x a couple of days ago from a german seller.Before that i had never seen a dbox and had only read a few guides online. It had a german Sportster image that was only picking up one or two channels.With a lot of excellent help and guidance i flashed the blade image using IFA yesterday and after a few different scans I finally got all(or nearly all) channels. only problem is some channels freeze or stutter. Most channels are perfect. I have tried all possible combinations of cams and ucodes but the affected channels have not noticeably improved. I am currently running gbox and ucode0014. If anyone has any ideas on how i can get these channels to settle down, I would really appreciate your help. Cheers!
Edit. I am now getting an error message when changing channels "keine karte eingesteckt!"?????????
This message has been edited since posting. Last time this message was edited on 20. June 2007 @ 09:34
|
|
mgb17
Senior Member
|
20. June 2007 @ 09:32 |
Link to this message
|
|
Check the numbers for BER SNR SIG for good and bad channels and compare it.
Red button -> blue button.
Check also the frequencies for some bad channels. Maybe your cables.xml is botched or you tried the wrong option.
|
|
srevor
Junior Member
|
20. June 2007 @ 10:05 |
Link to this message
|
|
This message has been edited since posting. Last time this message was edited on 20. June 2007 @ 10:08
|
Newbie
|
20. June 2007 @ 10:21 |
Link to this message
|
|
hey,does anybody know what might have happened my movie channels,they were all working perfect one minute and now im just left with a black screen and no sound on six out of eight of them.does anybody have any clues,thanks!
|
|
srevor
Junior Member
|
20. June 2007 @ 10:26 |
Link to this message
|
Originally posted by dtrocks_6:
hey,does anybody know what might have happened my movie channels,they were all working perfect one minute and now im just left with a black screen and no sound on six out of eight of them.does anybody have any clues,thanks!
same here. they werent working to well anyway but now they aren't working at all 0kbit/s bitrate on the stream info menu.
|
Senior Member
|
20. June 2007 @ 10:29 |
Link to this message
|
Originally posted by dtrocks_6:
hey,does anybody know what might have happened my movie channels,they were all working perfect one minute and now im just left with a black screen and no sound on six out of eight of them.does anybody have any clues,thanks!
You didnt chmod 755 your keys folder so they didnt update correctly
|
|
mgb17
Senior Member
|
20. June 2007 @ 10:34 |
Link to this message
|
|
|
|
srevor
Junior Member
|
20. June 2007 @ 10:47 |
Link to this message
|
|
ss1 - bad-386750.0 MHz
smfam -bad- 394750.0 MHz
smsci-fi bad- 394750.0 MHz
Cheltv- good- 418750 MHz
|
|
mgb17
Senior Member
|
20. June 2007 @ 10:54 |
Link to this message
|
|
Wrong frequencies.
386500 and so on should be right for NTL cable Dublin.
Go to the scan menue, select leave current bouquets in the bouquets line, selecet NTL cable Dublin in the provider line, disable fast scan/manual scan, start the scan.
|
|
srevor
Junior Member
|
20. June 2007 @ 10:58 |
Link to this message
|
Originally posted by mgb17:
Wrong frequencies.
386500 and so on should be right for NTL cable Dublin.
Go to the scan menue, select leave current bouquets in the bouquets line, selecet NTL cable Dublin in the provider line, disable fast scan/manual scan, start the scan.
im in Galway, scanned with cableie ntl bruteforce, tried ntl w+g but only got 11 channels. should i still goahead and scan ntl dublin like you said?
This message has been edited since posting. Last time this message was edited on 20. June 2007 @ 10:59
|
|
mgb17
Senior Member
|
20. June 2007 @ 11:02 |
Link to this message
|
|
The option W+G is untested because the blokes from Galway are not willing to give any feedback.
Try NTL cable Dublin.
By the way do you get true cable or NTL mmds?
|
|
srevor
Junior Member
|
20. June 2007 @ 11:03 |
Link to this message
|
|
true cable
|
|
srevor
Junior Member
|
20. June 2007 @ 11:09 |
Link to this message
|
|
scanned ntl dublin got 22 tv channels.18 work fine 4 dont work at all
|
|
mgb17
Senior Member
|
20. June 2007 @ 11:15 |
Link to this message
|
|
Which default frequency do you get from your pace box?
Upload the irish cables.xml to /var/tuxbox/config, delete the file scan.conf in the same folder, pull the plug.
Try NTL Dublin bf.
|
|
srevor
Junior Member
|
20. June 2007 @ 11:20 |
Link to this message
|
Originally posted by mgb17:
Which default frequency do you get from your pace box?
Dont know , how can I find out?
[/quote]
Upload the irish cables.xml to /var/tuxbox/config, delete the file scan.conf in the same folder, pull the plug.
Try NTL Dublin bf. [/quote]
ok i'll go check some tuts and try that
|
|
mgb17
Senior Member
|
20. June 2007 @ 11:33 |
Link to this message
|
|
From a other forum (only for pace boxes):
on your subscription box unplug from wall socket then on the box press and hold all the time the up and down arrow buttons on the box
then plug in the power still holding down on these buttons you will get a engineers menu then let go of the down and up buttons
in there you will find your netid and frequency and symbol rate
press the right arrow on subscription box to flick through the pages where you will find this information
if you are ready unplug and replug the subscription box without pressing the buttons
This message has been edited since posting. Last time this message was edited on 20. June 2007 @ 11:35
|
|
srevor
Junior Member
|
20. June 2007 @ 11:46 |
Link to this message
|
|
default freq 291.000 MHz
|
|
mgb17
Senior Member
|
20. June 2007 @ 11:52 |
Link to this message
|
|
A network scan via NTL cable Dublin or NTL cable W+G should be functional.
Are you sure fast scan/manual scan is disabled.
This message has been edited since posting. Last time this message was edited on 20. June 2007 @ 11:54
|
|
srevor
Junior Member
|
20. June 2007 @ 11:55 |
Link to this message
|
Originally posted by mgb17:
Are you sure fast scan/manual scan is disabled.
yes fast scan off, manual scan off.
|
|
Advertisement
|
|
|
|
mgb17
Senior Member
|
20. June 2007 @ 11:58 |
Link to this message
|
|
Either network scan is botched in your image or the network information table is missing in Galway.
Try NTL Dublin bf.
|
