|
Jungle Flasher Tutorial for STOCK 83850C Lite-ON (pictures included)
|
|
AfterDawn Addict
2 product reviews
|
25. September 2009 @ 17:46 |
Link to this message
|
Originally posted by Melux:
Still "device intro failed"
Someone had same problem (with jf) and fixed it basically by erasing and flashing it over dos with iprep.
Heres video: http://www.robinhoodsplayground.com/foru...hp?f=195&t=3226
have to buy USB stick tomorrow to test it out..
You can still get good flash chip properties in Jungle Flasher. How are you power cycling the drive?
|
|
Advertisement
|
|
|
|
|
mrhobbes
Junior Member
|
25. September 2009 @ 20:21 |
Link to this message
|
Bought a 360 arcade from dell. its the new lite-on. opened it up, jungleflasher saw the drive, but kept failing the key check. suddenly started getting 3 red rings and flashing green light. then i smelled a burning type smell. Thinking of just boxing it back up and sending back to dell. any thoughts? i read that the flashing green light can mean a bad flash or tray open error. thing is, jungleflasher couldnt read the key, so i must not have been turning on/off half tray open thing correctly. Should i just order the ck3 connectivity kit? every time i powered off the drive with the tray open, and pushed it half closed, when i powered it back on, the tray would automatically close. i assume this is why the key check failed. Anyway, think this box can still be salvaged?
|
AfterDawn Addict
2 product reviews
|
25. September 2009 @ 22:55 |
Link to this message
|
Originally posted by mrhobbes:
Bought a 360 arcade from dell. its the new lite-on. opened it up, jungleflasher saw the drive, but kept failing the key check. suddenly started getting 3 red rings and flashing green light. then i smelled a burning type smell. Thinking of just boxing it back up and sending back to dell. any thoughts? i read that the flashing green light can mean a bad flash or tray open error. thing is, jungleflasher couldnt read the key, so i must not have been turning on/off half tray open thing correctly. Should i just order the ck3 connectivity kit? every time i powered off the drive with the tray open, and pushed it half closed, when i powered it back on, the tray would automatically close. i assume this is why the key check failed. Anyway, think this box can still be salvaged?
Yeah I would just send it back.
|
|
Melux
Newbie
|
26. September 2009 @ 04:16 |
Link to this message
|
leerage: Power cycling it without ck3 (from back of the dvd drive, right after clicking ok to second erase warning, or Intro/device "yes") maybe theres my problem, i'am not fast enaugh.. lets see if il get second person here to help me with it :P
EDIT: and maybe by doing it over dos with iprep i dont have to be that fast? (with power cycling)
This message has been edited since posting. Last time this message was edited on 26. September 2009 @ 04:20
|
|
Melux
Newbie
|
26. September 2009 @ 05:59 |
Link to this message
|
Ok got someone help to improve my power cycling speed, guess that wasnt my problem still drive not recognized. dvd drives eyect button not working, xbox flashing green light..
with Iprep 009 (dos) it sayd no atapi devices present, also dvd-drive is not recognized @ PC's BIOS. so is it dead?
And another question, if its dead.. is it possible to swap it with another one? (benq)
This really sucks just bought that xbox :P
This message has been edited since posting. Last time this message was edited on 26. September 2009 @ 07:38
|
|
mrhobbes
Junior Member
|
26. September 2009 @ 08:21 |
Link to this message
|
Originally posted by leerage:
Originally posted by mrhobbes:
Bought a 360 arcade from dell. its the new lite-on. opened it up, jungleflasher saw the drive, but kept failing the key check. suddenly started getting 3 red rings and flashing green light. then i smelled a burning type smell. Thinking of just boxing it back up and sending back to dell. any thoughts? i read that the flashing green light can mean a bad flash or tray open error. thing is, jungleflasher couldnt read the key, so i must not have been turning on/off half tray open thing correctly. Should i just order the ck3 connectivity kit? every time i powered off the drive with the tray open, and pushed it half closed, when i powered it back on, the tray would automatically close. i assume this is why the key check failed. Anyway, think this box can still be salvaged?
Yeah I would just send it back.
Thanks, i am boxing it up and getting an exchange. Gonna pick up the ck3 kit too.
|
|
GTA2787
Member
|
26. September 2009 @ 20:11 |
Link to this message
|
|
@leerage
Are you planning to make a tutorial for flashed 8350 Or is it the same process
|
AfterDawn Addict
2 product reviews
|
26. September 2009 @ 20:18 |
Link to this message
|
Originally posted by GTA2787:
@leerage
Are you planning to make a tutorial for flashed 8350 Or is it the same process
I believe you could just use the same process. I'll look into it.
|
|
GTA2787
Member
|
26. September 2009 @ 22:18 |
Link to this message
|
|
When we half power the drive for the second time we have the same steps as we had initially
|
|
GTA2787
Member
|
27. September 2009 @ 23:15 |
Link to this message
|
Originally posted by leerage:
When decrypting the key of a 83850C Lite-ON, there is a chance that the key can be corrupted.
Did it ever happen to you ? What is the probability of this happening.
|
AfterDawn Addict
2 product reviews
|
28. September 2009 @ 00:24 |
Link to this message
|
Originally posted by GTA2787:
Originally posted by leerage:
When decrypting the key of a 83850C Lite-ON, there is a chance that the key can be corrupted.
Did it ever happen to you ? What is the probability of this happening.
It hasn't ever happened to me. Dealing with 74850C and 83850C Lite-ONs, I have never had a bad key when extracting/decrypting. I am not sure of the probability of it happening. But you should always take precaution and spoof to another drive first.
|
|
Melux
Newbie
|
28. September 2009 @ 10:39 |
Link to this message
|
Dont like to spam r smth like that, just unsure about 1 thing.
If i got my Dummy(inquiry,identify,key) from 83850c, can i swap it now for sure with benq drive?
Belive my 83850c is dead, ordering another one.
|
AfterDawn Addict
2 product reviews
|
28. September 2009 @ 10:55 |
Link to this message
|
Originally posted by Melux:
Dont like to spam r smth like that, just unsure about 1 thing.
If i got my Dummy(inquiry,identify,key) from 83850c, can i swap it now for sure with benq drive?
Belive my 83850c is dead, ordering another one.
You can spoof the info to a BenQ.
|
|
stub1982
Newbie
|
28. September 2009 @ 19:23 |
Link to this message
|
I really need help with this. I tried following the guide, I have a maximus usb xtractor and a xtractor unit that powers the drive. Just getting nowhere. Been following the guide, when I do the tray half open, then ok it, it asks for the tray to be full, so i open the tray. Then i get an error message when I ok it.
I been connecting the usb xtractor on the R707 hole at this point from the halfway drive to full drive. What am I doing wrong?
|
|
tinker197
Newbie
|
28. September 2009 @ 19:41 |
Link to this message
|
Originally posted by stub1982:
I really need help with this. I tried following the guide, I have a maximus usb xtractor and a xtractor unit that powers the drive. Just getting nowhere. Been following the guide, when I do the tray half open, then ok it, it asks for the tray to be full, so i open the tray. Then i get an error message when I ok it.
I been connecting the usb xtractor on the R707 hole at this point from the halfway drive to full drive. What am I doing wrong?
is your firmware 8385oc or the 7000 firmware if its 8385oc you dont need the probe
i had problems doing the 8385oc drive as my onboard sata ports nforce chipset were not compatible with jungle flasher you will need a via card
then power up the drive half tray open then click ok
when it asks you to open the tray full press the eject button to close the tray then eject to open the tray then click ok
it will ask for the tray to be put in the half open tray click ok i think you will need to power off half close draw then power up
then hit eject to close the tray then eject to open the tray and click ok it should know save you dummy and inquiery if it fails on the full open tray and you are using onboard sata then you will need the via card
|
AfterDawn Addict
2 product reviews
|
28. September 2009 @ 19:42 |
Link to this message
|
Originally posted by stub1982:
I really need help with this. I tried following the guide, I have a maximus usb xtractor and a xtractor unit that powers the drive. Just getting nowhere. Been following the guide, when I do the tray half open, then ok it, it asks for the tray to be full, so i open the tray. Then i get an error message when I ok it.
I been connecting the usb xtractor on the R707 hole at this point from the halfway drive to full drive. What am I doing wrong?
This is the tutorial for the 83850C Lite-ON. You don't use a key reader on this drive! Can you confirm what firmware revision you have?
|
|
stub1982
Newbie
|
28. September 2009 @ 20:02 |
Link to this message
|
Originally posted by tinker197:
Originally posted by stub1982:
I really need help with this. I tried following the guide, I have a maximus usb xtractor and a xtractor unit that powers the drive. Just getting nowhere. Been following the guide, when I do the tray half open, then ok it, it asks for the tray to be full, so i open the tray. Then i get an error message when I ok it.
I been connecting the usb xtractor on the R707 hole at this point from the halfway drive to full drive. What am I doing wrong?
is your firmware 8385oc or the 7000 firmware if its 8385oc you dont need the probe
i had problems doing the 8385oc drive as my onboard sata ports nforce chipset were not compatible with jungle flasher you will need a via card
then power up the drive half tray open then click ok
when it asks you to open the tray full press the eject button to close the tray then eject to open the tray then click ok
it will ask for the tray to be put in the half open tray click ok i think you will need to power off half close draw then power up
then hit eject to close the tray then eject to open the tray and click ok it should know save you dummy and inquiery if it fails on the full open tray and you are using onboard sata then you will need the via card
I was at the same stage as you on your earlier posts. Does the Via chipset work for you? Have I screwed up my drive using the probe? I can still play originals with the drive.
|
|
stub1982
Newbie
|
28. September 2009 @ 20:07 |
Link to this message
|
Sorry, forgot to mention that it is the 83850c firmware the drive has. I have a Nvidea motherboard, so I need the sata card. I have one but unsure if it works. My PCs HDD boots off sata on the motherboard. Should I install it on another HDD thats non sata and do it that way, switching off the Nvidea satas and try my card that way.
|
AfterDawn Addict
|
28. September 2009 @ 20:08 |
Link to this message
|
|
if you can still play games, you havent messed it up. just redo the flashing without the probe as its not needed.
Come talk with us on efnet at #elitemods !!! or just click ME
ALSO, DO NOT SEND ME MESSAGES ON LIVE REGARDING MODDING CONSOLES, OR HOW I PLAYED A CERTAIN GAME EARLY. I WILL NOT RESPOND. I WILL INSTEAD DELETE YOUR MESSAGE, AND BLOCK ALL COMMUNICATION FROM YOU. JUST SEND ME A PM ON HERE. |
|
stub1982
Newbie
|
28. September 2009 @ 20:21 |
Link to this message
|
|
Ok, glad to hear my drive is still good to flash. How do you do the drive open halfway, is it best to do it from power up of the pc. My pc wont detect it otherwise, is that the right way?
|
|
stub1982
Newbie
|
28. September 2009 @ 21:21 |
Link to this message
|
|
Sorry for asking so many questions, just wondering if it is easier to flash while the drive is still powered to the 360?
|
AfterDawn Addict
2 product reviews
|
28. September 2009 @ 21:29 |
Link to this message
|
You will need to use the XBOX 360 to power the drive. Press the eject button and eject the tray. Disconnect the DVD drive's power cable and push the tray halfway in. That is what you need to do in the LO83 process.
|
|
stub1982
Newbie
|
29. September 2009 @ 10:49 |
Link to this message
|
Wouldn't disconnecting the power cause the sata port to reset. Everytime I turn off the drive it wont detect in jungle flasher.
|
AfterDawn Addict
2 product reviews
|
29. September 2009 @ 11:09 |
Link to this message
|
Originally posted by stub1982:
Wouldn't disconnecting the power cause the sata port to reset. Everytime I turn off the drive it wont detect in jungle flasher.
No, that is the process. If you are having issues getting your drive detected, it could a driver issue or your SATA chipset is incompatible.
|
|
Advertisement
|
|
|
|
stub1982
Newbie
|
29. September 2009 @ 13:30 |
Link to this message
|
|
It shows in jungleflasher when i boot up withe the drive on, If i turn off the drive and leave and go back in the drive wont show up. So is it ok to do it without leaving jungleflasher?
|
