|
KRYPTVIEW A750
|
|
Senior Member
|
12. May 2009 @ 06:55 |
Link to this message
|
just downloaded firmware for arnet[download successful]when i go to tv and scan for channells,the box display goes to half a zero and tv picture break,s down to many coloured pixel,s.Ihave did this procedure many times for friends and it has allways worked,is the problem with the box?.im on nthell
|
|
Advertisement
|
|
|
|
|
fergusrb
Suspended permanently
|
12. May 2009 @ 07:08 |
Link to this message
|
Originally posted by supman101:
fergus would you please pm me the frequenciesfor the kv mmds as i am missing some channels i.e s*y spt 2 etc.
thanks in advance
get the freq from your other box and use them if you rescan your old box they will all come back in you just wont be able to watch then get the freq
|
Senior Member
|
12. May 2009 @ 07:54 |
Link to this message
|
Originally posted by reswob:
just downloaded firmware for arnet[download successful]when i go to tv and scan for channells,the box display goes to half a zero and tv picture break,s down to many coloured pixel,s.Ihave did this procedure many times for friends and it has allways worked,is the problem with the box?.im on nthell
just to update,ive opened box,can see no problem,tried different tv,tried different scarts,have since managed to recieve all channels since first post.but after watching tv for about 3 mins the screen goes green or white.when i switch button of and then on at back of box the display showes nothing at all.i have to wait for about 3 or 4 mins before i get the station back on,then it just repeats it self all over again.it sounds as if it,s a heat issue but the box is cold and well vented?
|
|
fergusrb
Suspended permanently
|
12. May 2009 @ 07:59 |
Link to this message
|
|
ok take the connectors off the box bot of them going to the main board and reseat them again and see what happens
you are using a full 21 pin both ends scart and its in the correct slot the first one nearest the cable input
|
Senior Member
|
12. May 2009 @ 08:12 |
Link to this message
|
Originally posted by fergusrb:
ok take the connectors off the box bot of them going to the main board and reseat them again and see what happens
you are using a full 21 pin both ends scart and its in the correct slot the first one nearest the cable input
its 20 pins both ends,sorry fergus what connectors,my own arnet is working fine on the set up i have
|
|
fergusrb
Suspended permanently
|
12. May 2009 @ 08:21 |
Link to this message
|
Originally posted by reswob:
Originally posted by reswob:
just downloaded firmware for arnet[download successful]when i go to tv and scan for channells,the box display goes to half a zero and tv picture break,s down to many coloured pixel,s.Ihave did this procedure many times for friends and it has allways worked,is the problem with the box?.im on nthell
just to update,ive opened box,can see no problem,tried different tv,tried different scarts,have since managed to recieve all channels since first post.but after watching tv for about 3 mins the screen goes green or white.when i switch button of and then on at back of box the display showes nothing at all.i have to wait for about 3 or 4 mins before i get the station back on,then it just repeats it self all over again.it sounds as if it,s a heat issue but the box is cold and well vented?
is this not your post saying you have a problem with your scart leads on your box ?? or is it just me going mad lol
This message has been edited since posting. Last time this message was edited on 12. May 2009 @ 08:21
|
Senior Member
|
12. May 2009 @ 08:33 |
Link to this message
|
Originally posted by fergusrb:
Originally posted by reswob:
Originally posted by reswob:
just downloaded firmware for arnet[download successful]when i go to tv and scan for channells,the box display goes to half a zero and tv picture break,s down to many coloured pixel,s.Ihave did this procedure many times for friends and it has allways worked,is the problem with the box?.im on nthell
just to update,ive opened box,can see no problem,tried different tv,tried different scarts,have since managed to recieve all channels since first post.but after watching tv for about 3 mins the screen goes green or white.when i switch button of and then on at back of box the display showes nothing at all.i have to wait for about 3 or 4 mins before i get the station back on,then it just repeats it self all over again.it sounds as if it,s a heat issue but the box is cold and well vented?
thats my post ok fergus;i have two box,s here at the moment one is afriends the other mine.as regards the problem, i dont think its the scart,s.i was trying to eliminate all possibilities by trying all the above.the problem seems to be the box,sorry for confusion
is this not your post saying you have a problem with your scart leads on your box ?? or is it just me going mad lol
|
|
fergusrb
Suspended permanently
|
12. May 2009 @ 08:52 |
Link to this message
|
is it possible the settings are wrong have a look select pal and cvbs or rgb vice versa and see it that is the problem
how is the signal levels press a channel then the info button
|
Senior Member
|
12. May 2009 @ 09:07 |
Link to this message
|
Originally posted by fergusrb:
is it possible the settings are wrong have a look select pal and cvbs or rgb vice versa and see it that is the problem
how is the signal levels press a channel then the info button
did as you asked,signsl level at 70.after a couple of mins display went to half a zero and screen went green?
|
|
fergusrb
Suspended permanently
|
12. May 2009 @ 09:26 |
Link to this message
|
|
ok did you put the other box on that connection as well as 0% means no signal check his cable that its not split anywhere ??
|
Senior Member
|
12. May 2009 @ 09:32 |
Link to this message
|
Originally posted by fergusrb:
ok did you put the other box on that connection as well as 0% means no signal check his cable that its not split anywhere ??
all i have is his box in my home on my cables.His settings are the same as mine. mine works his has the problem?
|
|
fergusrb
Suspended permanently
|
12. May 2009 @ 09:34 |
Link to this message
|
|
ok mate best to send it back to supplier make sure you send them an email first as you might need a ref number or something
|
Senior Member
|
12. May 2009 @ 09:42 |
Link to this message
|
Originally posted by fergusrb:
ok mate best to send it back to supplier make sure you send them an email first as you might need a ref number or something
will do fergus,Thanks for your time,sorry for confusion earlier.
|
|
fergusrb
Suspended permanently
|
12. May 2009 @ 10:05 |
Link to this message
|
|
not a bother mate happy to help when i can
|
Newbie
|
12. May 2009 @ 10:47 |
Link to this message
|
|
Hi all.new here.just need some help.
I'm getting a MMDS ariel next week from n*l.
So what would be the best "box" to get?I heard the ky A750 was good.
Also my laptop run's on vista and has no RS232 socket.
I live in Ratoath (Meath)
Oh and were's the best place to buy a box?
Thanks in advance.Tony
Tony
|
|
dubtony
Newbie
|
12. May 2009 @ 17:55 |
Link to this message
|
|
Hi folks
is the kryptview still working in the dublin area, and can anyone let me know where i might be able to get my hands on one
dubtony
|
|
fergusrb
Suspended permanently
|
12. May 2009 @ 18:10 |
Link to this message
|
|
ok at the present time there is no Kryptview boxes anywhere to be had they are all out of stock till the start of June you have missed you chance till then
i have just pm both of you above where to get when back in stock
|
|
TRYCOOL6
Suspended due to non-functional email address
|
13. May 2009 @ 04:30 |
Link to this message
|
|
just got a krypt view box 750, want to flash it , have been looking ttrough the posts and have a fair idea but could any body please send us a basic step by step instruction list,sorry i am only a newbi to all this ,
bob
|
Member
|
13. May 2009 @ 04:51 |
Link to this message
|
Originally posted by TRYCOOL6:
just got a krypt view box 750, want to flash it , have been looking ttrough the posts and have a fair idea but could any body please send us a basic step by step instruction list,sorry i am only a newbi to all this ,
Look at fergusrb post above yours and all the info is at the bottom
of his post by a simple few clicks.
|
|
jazirazi
Suspended due to non-functional email address
|
13. May 2009 @ 06:01 |
Link to this message
|
|
hi,
just wondering where to buy a kryptview in dublin. tx
|
|
fergusrb
Suspended permanently
|
13. May 2009 @ 06:18 |
Link to this message
|
Originally posted by jazirazi:
hi,
just wondering where to buy a kryptview in dublin. tx
all suppliers are out of Stock till June
check your pm messages
|
|
sniper121
Newbie
|
13. May 2009 @ 06:47 |
Link to this message
|
lads i got a USB to serial converter to download the software into the kryptview (via a null modem".
still getting an error "the software not requested"
any ideas?
|
|
sniper121
Newbie
|
13. May 2009 @ 07:56 |
Link to this message
|
|
WHEN I GO INTO PORTS IN DEVICE MANAGER ALL I HAVE IS ONE PRINTER PORT (LPT1)
|
Senior Member
|
13. May 2009 @ 08:01 |
Link to this message
|
Originally posted by sniper121:
WHEN I GO INTO PORTS IN DEVICE MANAGER ALL I HAVE IS ONE PRINTER PORT (LPT1)
Install the software drivers for the USB to serial converter.
-
|
|
Advertisement
|
|
|
|
sniper121
Newbie
|
13. May 2009 @ 08:46 |
Link to this message
|
|
Lads,
I'm up and running!!!! A big thank to you everyone on here esp Fergusrb. you guys are doing a great job.
keep it up.
|
