|
A NEWBIES GUIDE TO SETTING UP A DM500S FOR CARDSHARING
|
|
|
EAMO_TOO
Senior Member
|
10. January 2011 @ 05:13 |
Link to this message
|
Originally posted by fintannl:
eamo i do not support pay servers. i have said it over an over again. such folk are not the people to be sharing your credit card details with. this forum should not been seen as supporting any such threads on the basis it puts users at risk
Take your point Fintanni, it's just I know several people who pay servers without any problem.
|
|
Advertisement
|
 |
|
|
Senior Member
|
11. January 2011 @ 16:06 |
Link to this message
|
|
may be true eamo until they are busted and all the user details are plainly available to our police enforcement folks. hence the reason i will always advise users to stay away from such arrangements
|
Senior Member
|
11. January 2011 @ 16:07 |
Link to this message
|
|
may be true eamo until they are busted and all the user details are plainly available to our police enforcement folks. hence the reason i will always advise users to stay away from such arrangements
|
|
jhammer02
Junior Member
|
11. January 2011 @ 16:11 |
Link to this message
|
Please help - got a new dm800, flashed with gemini 4.2 it worked fine, then ftp the box to find cccam.cfg could not find. Then I flashed it with gemini2 4.7 and after rebooting it it says error er01 no ca found, please help
Thanks
Jhammer
|
Member
|
11. January 2011 @ 16:32 |
Link to this message
|
Originally posted by jhammer02:
Please help - got a new dm800, flashed with gemini 4.2 it worked fine, then ftp the box to find cccam.cfg could not find. Then I flashed it with gemini2 4.7 and after rebooting it it says error er01 no ca found, please help
Right,..the "no ca found" error is because or a bad flash or most likely in your case you flashed an image not suited to the bootloader on your dreambox,..if your box is new it should have bootloader 76 so only use images for that ( but check first.
Following the info below you will have to flash the correct bootloader first then flash an image suitable for that bootloader.
-> ERR01 : NO CA FOUND
Solution:
1) Use DreamUp 1.3.3 with serial (null modem) cable
2) Choose COM1, connect, power ON DM800 and wait
3) After a few seconds the DM800 screen will come back with an IP address
4) Type in that address in IE or firefox
5) Flash a BootLoader (the version that your box came with) reboot DM800 and hold power button
7) Wait for IP to appear on DM800 screen
8)Type in that address in IE
9) Flash your desired image
Dream Elite Black Hole Phoenix Edition Sim2.01 SSL84 DM800HD
|
|
scandalu
Suspended permanently
|
11. January 2011 @ 16:37 |
Link to this message
|
|
its usually less stressful if you are starting off and are new to the setup of things if you know someone with a reliable server who can do the whole package...i.e box plus c/s plus cccam etc for you...
i use a reliable source(non uk server) that has been reliable for past 7 years,and he supplies the whole package at a reasonable price with no headaches for me....but if your savvy with doing your own thing..good on u.....but we're not all that savvy!
|
Senior Member
|
11. January 2011 @ 16:58 |
Link to this message
|
|
jhammer power off the box and power it back on ,then look at the little lcd screen on the front of the box ,it should display your boxes sim and bootloader version .as lenny said if its new its most likely sim 2.01 bootloader76 (BL76) ,but check and then we can point you to a suitable image.
|
|
jhammer02
Junior Member
|
11. January 2011 @ 17:45 |
Link to this message
|
Which is the best image for Dm800? originally it came with bootloader 76. where do I download the bootloader from? thanks
|
Senior Member
|
11. January 2011 @ 18:22 |
Link to this message
|
|
Member
|
11. January 2011 @ 19:03 |
Link to this message
|
Dream Elite Black Hole Phoenix Edition Sim2.01 SSL84 DM800HD
|
|
jhammer02
Junior Member
|
12. January 2011 @ 03:43 |
Link to this message
|
Originally posted by lenny123:
Originally posted by piopat:
reflash your box with this image
http://www.dm800sim2.com/sim2/nabilosat/content/61/20091115/194.html
won't he need to flash the bootloader first ?? also that's a #75 image I think,..although it should be ok.
When I switch on the box it brings the error straight away. It came with bootkoader 76 sim 2.01
Do I have to flash the bootloader first if that is the case where do get the bootloader from and how do I do it. Thanks
|
Member
|
12. January 2011 @ 05:06 |
Link to this message
|
Originally posted by jhammer02:
Originally posted by lenny123:
Originally posted by piopat:
reflash your box with this image
http://www.dm800sim2.com/sim2/nabilosat/content/61/20091115/194.html
won't he need to flash the bootloader first ?? also that's a #75 image I think,..although it should be ok.
When I switch on the box it brings the error straight away. It came with bootkoader 76 sim 2.01
Do I have to flash the bootloader first if that is the case where do get the bootloader from and how do I do it. Thanks
Just to clarify,..you need to remove the power from the rear & re-insert the power connector whilst holding in the standby button on the front until the display shows an IP address,..if you are doing this & still get the error than you need to flash the bootloader first before you flash the image,...you need to follow the 9 steps in my previous post,..here are the bootloader & image you will need....you will need a null modem serial cable but if your computer does not have a serial port you need to get a usb to serial adaptor to use with the cable.
Dream Elite Black Hole Phoenix Edition Sim2.01 SSL84 DM800HD
|
Senior Member
|
12. January 2011 @ 09:42 |
Link to this message
|
|
the image i posted above will work on a sim 2.01 bl76 box (even tho its bl75) i have given it to a few people with the same issue.
|
Member
|
12. January 2011 @ 10:05 |
Link to this message
|
Originally posted by piopat:
the image i posted above will work on a sim 2.01 bl76 box (even tho its bl75) i have given it to a few people with the same issue.
Point taken,..but he can't flash it without sorting out his bootloader issue first by using dreamup...he initial problem was not being able to find the cccam.cfg file which led him to flash the box,...that would have been an easier task if he had asked here first.
Dream Elite Black Hole Phoenix Edition Sim2.01 SSL84 DM800HD
This message has been edited since posting. Last time this message was edited on 12. January 2011 @ 10:15
|
|
jicjoc
Junior Member
|
12. January 2011 @ 12:15 |
Link to this message
|
Hi Guys,
Same old problem back again.
Dyndns recognises my ip port 12000 as open in its open port tool, but it is not recognising my dns text string i created port 12000 as open.
Any idea's?
It works for a day or so and then breaks... :(
EDIT - I speak too soon. It was an issue here with my dyndns updater. It appeared to be working fine, but then showed a 'critical' fault. Which promptly fixed itself when i clicked the refresh. Strange, but i dont care if it works from now on...
Now, to another problem... How can i conviently run dyndns updater when i am not in the house, and dont want to leave a pc on 24/7? Im thinking about setting up a 'wake on lan' or something jobbie and then vnc in to the pc. Anyone any idea's?
Thanks!
This message has been edited since posting. Last time this message was edited on 12. January 2011 @ 12:20
|
|
jhammer02
Junior Member
|
12. January 2011 @ 12:23 |
Link to this message
|
Originally posted by lenny123:
Originally posted by jhammer02:
Originally posted by lenny123:
Originally posted by piopat:
reflash your box with this image
http://www.dm800sim2.com/sim2/nabilosat/content/61/20091115/194.html
won't he need to flash the bootloader first ?? also that's a #75 image I think,..although it should be ok.
When I switch on the box it brings the error straight away. It came with bootkoader 76 sim 2.01
Do I have to flash the bootloader first if that is the case where do get the bootloader from and how do I do it. Thanks
Just to clarify,..you need to remove the power from the rear & re-insert the power connector whilst holding in the standby button on the front until the display shows an IP address,..if you are doing this & still get the error than you need to flash the bootloader first before you flash the image,...you need to follow the 9 steps in my previous post,..here are the bootloader & image you will need....you will need a null modem serial cable but if your computer does not have a serial port you need to get a usb to serial adaptor to use with the cable.
When I am trying to load the file in dreamup it says file too big, please advise
Thanks
Jhammer
|
Member
|
12. January 2011 @ 16:29 |
Link to this message
|
Originally posted by jhammer02:
Originally posted by lenny123:
Originally posted by jhammer02:
Originally posted by lenny123:
Originally posted by piopat:
reflash your box with this image
http://www.dm800sim2.com/sim2/nabilosat/content/61/20091115/194.html
won't he need to flash the bootloader first ?? also that's a #75 image I think,..although it should be ok.
When I switch on the box it brings the error straight away. It came with bootkoader 76 sim 2.01
Do I have to flash the bootloader first if that is the case where do get the bootloader from and how do I do it. Thanks
Just to clarify,..you need to remove the power from the rear & re-insert the power connector whilst holding in the standby button on the front until the display shows an IP address,..if you are doing this & still get the error than you need to flash the bootloader first before you flash the image,...you need to follow the 9 steps in my previous post,..here are the bootloader & image you will need....you will need a null modem serial cable but if your computer does not have a serial port you need to get a usb to serial adaptor to use with the cable.
When I am trying to load the file in dreamup it says file too big, please advise
Try this,
1. make sure dm800 power not attached
2. put the serial cable from your pc to dm800.
3. click connect button on dreamup
4. now insert the power to the dm800.
5. the dreamup should be responded and start to upload
6. click flash and choose the bootloader which suits to your dm800.
7. after flashing, unplug the power of dm800 and remove the null modem cable.
8. connect your ethernet cable & power on the box again whilst holding in the standby button until you see the box IP then use IE/firefox to flash the image using the web browser.
Here is more helpfull information,..also HERE is a (patched) version of dreamup that works with 800 clones.
Dream Elite Black Hole Phoenix Edition Sim2.01 SSL84 DM800HD
This message has been edited since posting. Last time this message was edited on 12. January 2011 @ 18:09
|
|
4dbox
Account closed as per user's own request
|
12. January 2011 @ 17:15 |
Link to this message
|
|
quote]When I am trying to load the file in dreamup it says file too big, please advise
you then open a web page ie box ip will show in box screen and flash it via on screen
|
|
jhammer02
Junior Member
|
12. January 2011 @ 18:05 |
Link to this message
|
Originally posted by 4dbox:
quote]When I am trying to load the file in dreamup it says file too big, please advise
you then open a web page ie box ip will show in box screen and flash it via on screen
All I have managed to fix my dream box 800 hd for the error no can found & file too big. First of all thank you all for your support & guidance. If anyone needs help do ask me
|
Member
|
12. January 2011 @ 18:10 |
Link to this message
|
Originally posted by jhammer02:
Originally posted by 4dbox:
quote]When I am trying to load the file in dreamup it says file too big, please advise
you then open a web page ie box ip will show in box screen and flash it via on screen
All I have managed to fix my dream box 800 hd for the error no can found & file too big. First of all thank you all for your support & guidance. If anyone needs help do ask me
great,...so tell us what you did,..step by step
Dream Elite Black Hole Phoenix Edition Sim2.01 SSL84 DM800HD
|
|
jhammer02
Junior Member
|
13. January 2011 @ 08:43 |
Link to this message
|
Dreambox 800 HD Problem - ERR01 : NO CA found & file too big
If this is the problem you are experiencing then follow the below steps - guaranteed solution (Make sure you are using a computer with Windows XP, this wont work on Windows Vista) -
1. Get a null modem cable if your computer doesn't have a serial port get a serial to usb adaptor also.
2. Software needed is - Dreamup 1.3.3.2 and Enforcer (this enforcer is the magic software which does the trick).
3. Unplug power cable from the box.
4. Plug the serial cable to the box and the other end should be connected to your computer.
5. Open device manager of your computer and check which port is configured for your serial to usb cable (example - COM1 or COM2 whatever it is)
6. Open dreamup and then start Enforcer
7. Now drag the Enforcer on top of the dreamup and click on Enable (in Enforcer).
8. Then you will notice that the Flash button on Dreamup is enabled now which was greyed out.
9. Now select the port in Dreamup which is configured for your serial cable (Com1 or Com2 whatever it is), then press connect button on Dreamup and plug in the power cable in your box. You should notice that the dreamup is running a flash and the box type is displayed as your box model at the bottom left corner of Dreamup.
10. Now press the Flash button on Dreamup and browse to the image which you want to load (I know which one works the best but I dont know whether I can and how I should provide link to it here.)
11. When you have selected the image it will flash the box with that and take approx 1 hour to complete since the serial cable is slow to transfer data.
12. Once finished unplug the serial cable and power cable from the box wait for 1 minute and then plug in the power cable to the box and connect it to your tv. It will start with the basic setup wizard which I hope you guys know how to set it up and do gemini server then cccam and cccam config. Thats the box should be up and running.
Thanks
|
Senior Member
|
13. January 2011 @ 16:36 |
Link to this message
|
|
jhammer, enforcer download link please
|
Member
|
13. January 2011 @ 16:49 |
Link to this message
|
Originally posted by fintannl:
jhammer, enforcer download link please
here's a link to a collection of dreambox tools including enforcer,..enforcer should only be used when the normal dreamup method fails.
Dreambox Tools
Dream Elite Black Hole Phoenix Edition Sim2.01 SSL84 DM800HD
|
|
jhammer02
Junior Member
|
13. January 2011 @ 17:24 |
Link to this message
|
Originally posted by fintannl:
jhammer, enforcer download link please
Here is the link for enforcer
link
|
|
Advertisement
|
|
|
Senior Member
|
14. January 2011 @ 16:04 |
Link to this message
|
thanks jhammer, can someone give me a brief description of this tool. i have never had a need to use it. jicjoc, please use inadyn plugin which is available for download on your dreambox instead of dyndns updater on your computer. why would you want to have your computer doing the update for you when your dreambox will do it easily
|
